ノートパソコン(nec ll350bd)をbuffaloのwli2-cb-g54lというpcカードを使って無線lanに接続させようとしました。
ecolinux10.04（ubuntu10.04の派生）にndiswrapperを入れ、buffaloの公式ドライバを解凍したinfファイルで認識に成功、wicdというのでアクセスポイントの一覧の表示もできました。しかし、そこからの接続ができません。電波もいいのに、「パスワードが間違っています」とでたり、「ipアドレスの取得に失敗しました」とでてしまいます。親機はnecのaterm wr8300nで、暗号化方式はwpa/wpa2-psk(aes)です。wepに変えても同じくだめでした。wicd側の暗号化方式も色々試しましたがダメでした。暗号化が問題なのかと思い、暗号化なしのアクセスポイントに接続を試みましたが同じでした。また、ndiswrapperの公式wikiでを調べたところacerのドライバをつかえと書いてあったのですが変わりませんでした。

解決策があれば回答よろしくお願いいたします。


dmesg,lsmod,lspciの結果を投稿しておきます。

--dmesg--
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.32-45-generic (buildd@aatxe) (gcc version 4.4.3 (Ubuntu 4.4.3-4ubuntu5.1) ) #99-Ubuntu SMP Tue Oct 16 16:31:11 UTC 2012 (Ubuntu 2.6.32-45.99-generic 2.6.32.60+drm33.26)
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   NSC Geode by NSC
[    0.000000]   Cyrix CyrixInstead
[    0.000000]   Centaur CentaurHauls
[    0.000000]   Transmeta GenuineTMx86
[    0.000000]   Transmeta TransmetaCPU
[    0.000000]   UMC UMC UMC UMC
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
[    0.000000]  BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000000def0000 (usable)
[    0.000000]  BIOS-e820: 000000000def0000 - 000000000deff000 (ACPI data)
[    0.000000]  BIOS-e820: 000000000deff000 - 000000000df00000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000000df00000 - 000000000e000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[    0.000000] DMI present.
[    0.000000] last_pfn = 0xdef0 max_arch_pfn = 0x100000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CFFFF write-protect
[    0.000000]   D0000-DEFFF uncachable
[    0.000000]   DF000-DFFFF write-protect
[    0.000000]   E0000-E3FFF write-back
[    0.000000]   E4000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask FF8000000 write-back
[    0.000000]   1 base 008000000 mask FFC000000 write-back
[    0.000000]   2 base 00C000000 mask FFE000000 write-back
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820 update range: 0000000000002000 - 0000000000006000 (usable) ==> (reserved)
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] modified physical RAM map:
[    0.000000]  modified: 0000000000000000 - 0000000000002000 (usable)
[    0.000000]  modified: 0000000000002000 - 0000000000006000 (reserved)
[    0.000000]  modified: 0000000000006000 - 000000000009f400 (usable)
[    0.000000]  modified: 000000000009f400 - 00000000000a0000 (reserved)
[    0.000000]  modified: 00000000000dc000 - 0000000000100000 (reserved)
[    0.000000]  modified: 0000000000100000 - 000000000def0000 (usable)
[    0.000000]  modified: 000000000def0000 - 000000000deff000 (ACPI data)
[    0.000000]  modified: 000000000deff000 - 000000000df00000 (ACPI NVS)
[    0.000000]  modified: 000000000df00000 - 000000000e000000 (reserved)
[    0.000000]  modified: 00000000fff80000 - 0000000100000000 (reserved)
[    0.000000] initial memory mapped : 0 - 00c00000
[    0.000000] init_memory_mapping: 0000000000000000-000000000def0000
[    0.000000] Using x86 segment limits to approximate NX protection
[    0.000000]  0000000000 - 0000400000 page 4k
[    0.000000]  0000400000 - 000dc00000 page 2M
[    0.000000]  000dc00000 - 000def0000 page 4k
[    0.000000] kernel direct mapping tables up to def0000 @ 7000-c000
[    0.000000] RAMDISK: 09fd0000 - 0a773820
[    0.000000] ACPI: RSDP 000f7fe0 00014 (v00 PTLTD )
[    0.000000] ACPI: RSDT 0defbcce 0002C (v01 PTLTD    RSDT   06040000  LTP 00000000)
[    0.000000] ACPI: FACP 0defee74 00074 (v01 NEC    ND000080 06040000 MSTF 0100000E)
[    0.000000] ACPI: DSDT 0defbcfa 0317A (v01    NEC ND000080 06040000 MSFT 0100000E)
[    0.000000] ACPI: FACS 0defffc0 00040
[    0.000000] ACPI: SSDT 0defeee8 00118 (v01 PTLTD  POWERNOW 06040000  LTP 00000001)
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 222MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 0def0000
[    0.000000]   low ram: 0 - 0def0000
[    0.000000]   node 0 low ram: 00000000 - 0def0000
[    0.000000]   node 0 bootmap 00008000 - 00009be0
[    0.000000] (9 early reservations) ==> bootmem [0000000000 - 000def0000]
[    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
[    0.000000]   #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
[    0.000000]   #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
[    0.000000]   #3 [0000100000 - 00008e5ef8]    TEXT DATA BSS ==> [0000100000 - 00008e5ef8]
[    0.000000]   #4 [0009fd0000 - 000a773820]          RAMDISK ==> [0009fd0000 - 000a773820]
[    0.000000]   #5 [000009f400 - 0000100000]    BIOS reserved ==> [000009f400 - 0000100000]
[    0.000000]   #6 [00008e6000 - 00008e91ac]              BRK ==> [00008e6000 - 00008e91ac]
[    0.000000]   #7 [0000007000 - 0000008000]          PGTABLE ==> [0000007000 - 0000008000]
[    0.000000]   #8 [0000008000 - 000000a000]          BOOTMAP ==> [0000008000 - 000000a000]
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000000 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x0000def0
[    0.000000]   HighMem  0x0000def0 -> 0x0000def0
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[3] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00000002
[    0.000000]     0: 0x00000006 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x0000def0
[    0.000000] On node 0 totalpages: 56971
[    0.000000] free_area_init_node: node 0, pgdat c07a0800, node_mem_map c1001000
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3963 pages, LIFO batch:0
[    0.000000]   Normal zone: 414 pages used for memmap
[    0.000000]   Normal zone: 52562 pages, LIFO batch:15
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x8008
[    0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[    0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[    0.000000] APIC: disable apic facility
[    0.000000] nr_irqs_gsi: 16
[    0.000000] PM: Registered nosave memory: 0000000000002000 - 0000000000006000
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000dc000
[    0.000000] PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at e000000 (gap: e000000:f1f80000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1
[    0.000000] PERCPU: Embedded 14 pages/cpu @c1400000 s36056 r0 d21288 u4194304
[    0.000000] pcpu-alloc: s36056 r0 d21288 u4194304 alloc=1*4194304
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 56525
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-45-generic root=UUID=003091f5-b711-4a63-9fe0-3147df196f9a ro quiet splash
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Initializing CPU#0
[    0.000000] allocated 1141440 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Initializing HighMem for node 0 (00000000:00000000)
[    0.000000] Memory: 208420k/228288k available (4702k kernel code, 19140k reserved, 2124k data, 664k init, 0k highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xfff1d000 - 0xfffff000   ( 904 kB)
[    0.000000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.000000]     vmalloc : 0xce6f0000 - 0xff7fe000   ( 785 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xcdef0000   ( 222 MB)
[    0.000000]       .init : 0xc07ab000 - 0xc0851000   ( 664 kB)
[    0.000000]       .data : 0xc0597af7 - 0xc07aadc8   (2124 kB)
[    0.000000]       .text : 0xc0100000 - 0xc0597af7   (4702 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:2304 nr_irqs:256
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 1799.824 MHz processor.
[    0.004009] Calibrating delay loop (skipped), value calculated using timer frequency.. 3599.64 BogoMIPS (lpj=7199296)
[    0.004042] Security Framework initialized
[    0.004090] AppArmor: AppArmor initialized
[    0.004103] Mount-cache hash table entries: 512
[    0.004334] Initializing cgroup subsys ns
[    0.004341] Initializing cgroup subsys cpuacct
[    0.004348] Initializing cgroup subsys memory
[    0.004364] Initializing cgroup subsys devices
[    0.004368] Initializing cgroup subsys freezer
[    0.004372] Initializing cgroup subsys net_cls
[    0.004403] Enabling disabled K7/SSE Support.
[    0.004408] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[    0.004413] CPU: L2 Cache: 512K (64 bytes/line)
[    0.004420] mce: CPU supports 4 MCE banks
[    0.004452] Performance Events: AMD PMU driver.
[    0.004467] ... version:                0
[    0.004469] ... bit width:              48
[    0.004472] ... generic registers:      4
[    0.004475] ... value mask:             0000ffffffffffff
[    0.004478] ... max period:             00007fffffffffff
[    0.004481] ... fixed-purpose events:   0
[    0.004483] ... event mask:             000000000000000f
[    0.004490] Checking 'hlt' instruction... OK.
[    0.020766] SMP alternatives: switching to UP code
[    0.028919] Freeing SMP alternatives: 19k freed
[    0.028964] ACPI: Core revision 20090903
[    0.037454] ACPI: setting ELCR to 0200 (from 06b8)
[    0.038541] ftrace: converting mcount calls to 0f 1f 44 00 00
[    0.038560] ftrace: allocating 21848 entries in 43 pages
[    0.044099] Enabling APIC mode:  Flat.  Using 0 I/O APICs
[    0.044107] weird, boot CPU (#0) not listed by the BIOS.
[    0.044110] SMP motherboard not detected.
[    0.044115] Local APIC not detected. Using dummy APIC emulation.
[    0.044118] SMP disabled
[    0.044613] Brought up 1 CPUs
[    0.044617] Total of 1 processors activated (3599.64 BogoMIPS).
[    0.044646] CPU0 attaching NULL sched-domain.
[    0.044926] devtmpfs: initialized
[    0.045488] regulator: core version 0.5
[    0.045521] Time: 13:26:22  Date: 11/10/12
[    0.045609] NET: Registered protocol family 16
[    0.045827] EISA bus registered
[    0.045852] ACPI: bus type pci registered
[    0.046280] PCI: PCI BIOS revision 2.10 entry at 0xfd9b3, last bus=1
[    0.047617] bio: create slab <bio-0> at 0
[    0.048359] ACPI: EC: Look up EC in DSDT
[    0.051546] ACPI: Interpreter enabled
[    0.051553] ACPI: (supports S0 S3 S4 S5)
[    0.051580] ACPI: Using PIC for interrupt routing
[    0.060061] ACPI: EC: GPE = 0x1b, I/O: command/status = 0x66, data = 0x62
[    0.060129] ACPI: Power Resource [QFAN] (off)
[    0.060278] ACPI: No dock devices found.
[    0.060439] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.060512] pci 0000:00:00.0: reg 10 32bit mmio: [0xe8000000-0xebffffff]
[    0.060744] pci 0000:00:02.0: Enabling SiS 96x SMBus
[    0.060815] pci 0000:00:02.1: reg 20 io port: [0x8100-0x811f]
[    0.060879] pci 0000:00:02.5: reg 10 io port: [0x1f0-0x1f7]
[    0.060889] pci 0000:00:02.5: reg 14 io port: [0x3f4-0x3f7]
[    0.060899] pci 0000:00:02.5: reg 18 io port: [0x170-0x177]
[    0.060909] pci 0000:00:02.5: reg 1c io port: [0x374-0x377]
[    0.060919] pci 0000:00:02.5: reg 20 io port: [0x2800-0x280f]
[    0.060993] pci 0000:00:02.6: reg 10 io port: [0x1000-0x10ff]
[    0.061003] pci 0000:00:02.6: reg 14 io port: [0x2400-0x247f]
[    0.061080] pci 0000:00:02.6: supports D1 D2
[    0.061083] pci 0000:00:02.6: PME# supported from D3hot D3cold
[    0.061090] pci 0000:00:02.6: PME# disabled
[    0.061145] pci 0000:00:02.7: reg 10 io port: [0x1400-0x14ff]
[    0.061156] pci 0000:00:02.7: reg 14 io port: [0x2480-0x24ff]
[    0.061231] pci 0000:00:02.7: supports D1 D2
[    0.061234] pci 0000:00:02.7: PME# supported from D3hot D3cold
[    0.061240] pci 0000:00:02.7: PME# disabled
[    0.061276] pci 0000:00:03.0: reg 10 32bit mmio: [0xec004000-0xec004fff]
[    0.061358] pci 0000:00:03.1: reg 10 32bit mmio: [0xec005000-0xec005fff]
[    0.061455] pci 0000:00:03.2: reg 10 32bit mmio: [0xec006000-0xec006fff]
[    0.061535] pci 0000:00:03.2: PME# supported from D0 D3hot D3cold
[    0.061541] pci 0000:00:03.2: PME# disabled
[    0.061602] pci 0000:00:04.0: reg 10 io port: [0x1800-0x18ff]
[    0.061612] pci 0000:00:04.0: reg 14 32bit mmio: [0xec007000-0xec007fff]
[    0.061650] pci 0000:00:04.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
[    0.061691] pci 0000:00:04.0: supports D1 D2
[    0.061694] pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.061700] pci 0000:00:04.0: PME# disabled
[    0.061763] pci 0000:00:0a.0: reg 10 32bit mmio: [0xec008000-0xec008fff]
[    0.061805] pci 0000:00:0a.0: supports D1 D2
[    0.061808] pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.061814] pci 0000:00:0a.0: PME# disabled
[    0.061866] pci 0000:00:0a.1: reg 10 32bit mmio: [0xec009000-0xec0097ff]
[    0.061877] pci 0000:00:0a.1: reg 14 32bit mmio: [0xec000000-0xec003fff]
[    0.061953] pci 0000:00:0a.1: supports D1 D2
[    0.061956] pci 0000:00:0a.1: PME# supported from D0 D1 D2 D3hot
[    0.061962] pci 0000:00:0a.1: PME# disabled
[    0.062073] pci 0000:01:00.0: reg 10 32bit mmio pref: [0xf0000000-0xf7ffffff]
[    0.062082] pci 0000:01:00.0: reg 14 32bit mmio: [0xec300000-0xec31ffff]
[    0.062090] pci 0000:01:00.0: reg 18 io port: [0xa000-0xa07f]
[    0.062153] pci 0000:01:00.0: supports D1 D2
[    0.062208] pci 0000:00:01.0: bridge io port: [0xa000-0xafff]
[    0.062215] pci 0000:00:01.0: bridge 32bit mmio: [0xec300000-0xec3fffff]
[    0.062223] pci 0000:00:01.0: bridge 32bit mmio pref: [0xf0000000-0xf7ffffff]
[    0.062259] pci_bus 0000:00: on NUMA node 0
[    0.062265] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.073910] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 *7 10)
[    0.074048] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10) *9
[    0.074184] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10)
[    0.074319] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 *4 5 7 10)
[    0.074489] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10) *9
[    0.074625] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 *10)
[    0.074760] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10) *0, disabled.
[    0.074895] ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 7 10)
[    0.075077] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.075081] vgaarb: loaded
[    0.075284] SCSI subsystem initialized
[    0.075401] libata version 3.00 loaded.
[    0.075533] usbcore: registered new interface driver usbfs
[    0.075562] usbcore: registered new interface driver hub
[    0.075611] usbcore: registered new device driver usb
[    0.075818] ACPI: WMI: Mapper loaded
[    0.075820] PCI: Using ACPI for IRQ routing
[    0.076069] NetLabel: Initializing
[    0.076072] NetLabel:  domain hash size = 128
[    0.076075] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.076108] NetLabel:  unlabeled traffic allowed by default
[    0.076165] Switching to clocksource tsc
[    0.079472] AppArmor: AppArmor Filesystem Enabled
[    0.079522] pnp: PnP ACPI init
[    0.079568] ACPI: bus type pnp registered
[    0.082583] pnp: PnP ACPI: found 8 devices
[    0.082586] ACPI: ACPI bus type pnp unregistered
[    0.082593] PnPBIOS: Disabled by ACPI PNP
[    0.082619] system 00:04: ioport range 0x8000-0x808f has been reserved
[    0.082623] system 00:04: ioport range 0x8100-0x811f has been reserved
[    0.082627] system 00:04: ioport range 0x4d0-0x4d1 has been reserved
[    0.082631] system 00:04: ioport range 0xfe00-0xfe00 has been reserved
[    0.082635] system 00:04: ioport range 0x200-0x20f has been reserved
[    0.082639] system 00:04: ioport range 0x481-0x483 has been reserved
[    0.082643] system 00:04: ioport range 0x487-0x487 has been reserved
[    0.082646] system 00:04: ioport range 0x489-0x489 has been reserved
[    0.082650] system 00:04: ioport range 0x48a-0x48b has been reserved
[    0.082654] system 00:04: ioport range 0x48f-0x48f has been reserved
[    0.082660] system 00:04: iomem range 0xfee00000-0xfee00fff has been reserved
[    0.082664] system 00:04: iomem range 0xffee0000-0xffef5fff has been reserved
[    0.082669] system 00:04: iomem range 0xffef6000-0xffefffff has been reserved
[    0.082673] system 00:04: iomem range 0xfec00000-0xfec0ffff has been reserved
[    0.082677] system 00:04: iomem range 0xd0000-0xfffff could not be reserved
[    0.117503] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[    0.117509] pci 0000:00:01.0:   IO window: 0xa000-0xafff
[    0.117520] pci 0000:00:01.0:   MEM window: 0xec300000-0xec3fffff
[    0.117527] pci 0000:00:01.0:   PREFETCH window: 0xf0000000-0xf7ffffff
[    0.117538] pci 0000:00:0a.0: CardBus bridge, secondary bus 0000:02
[    0.117542] pci 0000:00:0a.0:   IO window: 0x001c00-0x001cff
[    0.117549] pci 0000:00:0a.0:   IO window: 0x002000-0x0020ff
[    0.117556] pci 0000:00:0a.0:   PREFETCH window: 0x10000000-0x13ffffff
[    0.117562] pci 0000:00:0a.0:   MEM window: 0x14000000-0x17ffffff
[    0.117815] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
[    0.117819] PCI: setting IRQ 10 as level-triggered
[    0.117826] pci 0000:00:0a.0: PCI INT A -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10
[    0.117838] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
[    0.117842] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[    0.117846] pci_bus 0000:01: resource 0 io:  [0xa000-0xafff]
[    0.117850] pci_bus 0000:01: resource 1 mem: [0xec300000-0xec3fffff]
[    0.117853] pci_bus 0000:01: resource 2 pref mem [0xf0000000-0xf7ffffff]
[    0.117857] pci_bus 0000:02: resource 0 io:  [0x1c00-0x1cff]
[    0.117861] pci_bus 0000:02: resource 1 io:  [0x2000-0x20ff]
[    0.117864] pci_bus 0000:02: resource 2 pref mem [0x10000000-0x13ffffff]
[    0.117868] pci_bus 0000:02: resource 3 mem: [0x14000000-0x17ffffff]
[    0.117932] NET: Registered protocol family 2
[    0.118077] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.118468] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.118664] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.118847] TCP: Hash tables configured (established 8192 bind 8192)
[    0.118851] TCP reno registered
[    0.118950] NET: Registered protocol family 1
[    0.119224] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
[    0.119230] pci 0000:00:03.0: PCI INT A -> Link[LNKE] -> GSI 10 (level, low) -> IRQ 10
[    0.335854] pci 0000:00:03.0: PCI INT A disabled
[    0.336063] ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 10
[    0.336068] pci 0000:00:03.1: PCI INT B -> Link[LNKF] -> GSI 10 (level, low) -> IRQ 10
[    0.551882] pci 0000:00:03.1: PCI INT B disabled
[    0.552095] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 3
[    0.552098] PCI: setting IRQ 3 as level-triggered
[    0.552104] pci 0000:00:03.2: PCI INT D -> Link[LNKH] -> GSI 3 (level, low) -> IRQ 3
[    0.552124] pci 0000:00:03.2: PCI INT D disabled
[    0.552138] pci 0000:01:00.0: Boot video device
[    0.552414] cpufreq-nforce2: No nForce2 chipset.
[    0.552450] Scanning for low memory corruption every 60 seconds
[    0.552675] audit: initializing netlink socket (disabled)
[    0.552695] type=2000 audit(1352553982.000:1): initialized
[    0.563748] Trying to unpack rootfs image as initramfs...
[    0.576231] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.583975] VFS: Disk quotas dquot_6.5.2
[    0.584186] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.585124] fuse init (API version 7.13)
[    0.585249] msgmni has been set to 407
[    0.585639] alg: No test for stdrng (krng)
[    0.585688] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.585694] io scheduler noop registered
[    0.585696] io scheduler anticipatory registered
[    0.585699] io scheduler deadline registered
[    0.585750] io scheduler cfq registered (default)
[    0.585932] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.585966] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.586226] ACPI: AC Adapter [ACAD] (off-line)
[    0.586359] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[    0.592032] ACPI: Lid Switch [LID]
[    0.592219] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[    0.592227] ACPI: Power Button [PWB]
[    0.592305] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[    0.592310] ACPI: Power Button [PWRF]
[    0.592457] fan PNP0C0B:00: registered as cooling_device0
[    0.592466] ACPI: Fan [FAN] (off)
[    0.592646] Marking TSC unstable due to TSC halts in idle
[    0.592693] processor LNXCPU:00: registered as cooling_device1
[    0.594587] Switching to clocksource acpi_pm
[    0.597714] thermal LNXTHERM:01: registered as thermal_zone0
[    0.597726] ACPI: Thermal Zone [THRM] (50 C)
[    0.604890] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.605593] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
[    0.605599] PCI: setting IRQ 5 as level-triggered
[    0.605605] serial 0000:00:02.6: PCI INT C -> Link[LNKC] -> GSI 5 (level, low) -> IRQ 5
[    0.605616] serial 0000:00:02.6: PCI INT C disabled
[    0.607131] brd: module loaded
[    0.607856] loop: module loaded
[    0.608137] isapnp: Scanning for PnP cards...
[    0.615337] input: Macintosh mouse button emulation as /devices/virtual/input/input3
[    0.615619] pata_sis 0000:00:02.5: version 0.5.2
[    0.615965] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 7
[    0.615969] PCI: setting IRQ 7 as level-triggered
[    0.615976] pata_sis 0000:00:02.5: PCI INT A -> Link[LNKA] -> GSI 7 (level, low) -> IRQ 7
[    0.619109] scsi0 : pata_sis
[    0.662935] scsi1 : pata_sis
[    0.664218] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x2800 irq 14
[    0.664222] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x2808 irq 15
[    0.664833] Fixed MDIO Bus: probed
[    0.664890] PPP generic driver version 2.4.2
[    0.665064] tun: Universal TUN/TAP device driver, 1.6
[    0.665067] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[    0.665232] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.665284] ehci_hcd 0000:00:03.2: PCI INT D -> Link[LNKH] -> GSI 3 (level, low) -> IRQ 3
[    0.665333] ehci_hcd 0000:00:03.2: EHCI Host Controller
[    0.665405] ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 1
[    0.665489] ehci_hcd 0000:00:03.2: cache line size of 64 is not supported
[    0.665540] ehci_hcd 0000:00:03.2: irq 3, io mem 0xec006000
[    0.676422] ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00
[    0.676732] usb usb1: configuration #1 chosen from 1 choice
[    0.676786] hub 1-0:1.0: USB hub found
[    0.676813] hub 1-0:1.0: 6 ports detected
[    0.676932] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.676981] ohci_hcd 0000:00:03.0: PCI INT A -> Link[LNKE] -> GSI 10 (level, low) -> IRQ 10
[    0.677022] ohci_hcd 0000:00:03.0: OHCI Host Controller
[    0.677090] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
[    0.677134] ohci_hcd 0000:00:03.0: irq 10, io mem 0xec004000
[    0.754873] usb usb2: configuration #1 chosen from 1 choice
[    0.754932] hub 2-0:1.0: USB hub found
[    0.754962] hub 2-0:1.0: 3 ports detected
[    0.755071] ohci_hcd 0000:00:03.1: PCI INT B -> Link[LNKF] -> GSI 10 (level, low) -> IRQ 10
[    0.755113] ohci_hcd 0000:00:03.1: OHCI Host Controller
[    0.755201] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
[    0.755241] ohci_hcd 0000:00:03.1: irq 10, io mem 0xec005000
[    0.844421] usb usb3: configuration #1 chosen from 1 choice
[    0.844480] hub 3-0:1.0: USB hub found
[    0.844507] hub 3-0:1.0: 3 ports detected
[    0.844629] uhci_hcd: USB Universal Host Controller Interface driver
[    0.844802] PNP: PS/2 Controller [PNP0303:KBC1,PNP0f0e:MSE0] at 0x60,0x64 irq 1,12
[    0.859210] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.859228] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.860402] ata1.00: ATA-6: TOSHIBA MK4025GAS, KA108N, max UDMA/100
[    0.860406] ata1.00: 78140160 sectors, multi 16: LBA
[    0.862008] mice: PS/2 mouse device common for all mice
[    0.862363] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[    0.862391] rtc0: alarms up to one year, y3k, 114 bytes nvram
[    0.864151] device-mapper: uevent: version 1.0.3
[    0.864383] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: [email protected]
[    0.868784] ata1.00: configured for UDMA/100
[    0.868827] device-mapper: multipath: version 1.1.0 loaded
[    0.868859] device-mapper: multipath round-robin: version 1.0.0 loaded
[    0.869222] EISA: Probing bus 0 at eisa.0
[    0.869236] Cannot allocate resource for EISA slot 1
[    0.869240] Cannot allocate resource for EISA slot 2
[    0.869262] Cannot allocate resource for EISA slot 8
[    0.869265] EISA: Detected 0 cards.
[    0.871054] cpuidle: using governor ladder
[    0.871116] cpuidle: using governor menu
[    0.871677] TCP cubic registered
[    0.871924] NET: Registered protocol family 10
[    0.873094] NET: Registered protocol family 17
[    0.873162] powernow-k8: Processor cpuid 6a0 not supported
[    0.873264] powernow: PowerNOW! Technology present. Can scale: frequency and voltage.
[    0.880350] powernow: SGTC: 13333
[    0.880356] powernow: Minimum speed 533 MHz. Maximum speed 1799 MHz.
[    0.880451] Using IPI No-Shortcut mode
[    0.880654] PM: Resume from disk failed.
[    0.880697] registered taskstats version 1
[    0.881042]   Magic number: 4:534:432
[    0.882328] rtc_cmos 00:02: setting system clock to 2012-11-10 13:26:23 UTC (1352553983)
[    0.882335] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.882337] EDD information not available.
[    0.966651] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[    1.075320] ACPI: Battery Slot [BAT1] (battery present)
[    1.234255] Freeing initrd memory: 7822k freed
[    1.298540] isapnp: No Plug & Play device found
[    1.298867] scsi 0:0:0:0: Direct-Access     ATA      TOSHIBA MK4025GA KA10 PQ: 0 ANSI: 5
[    1.299216] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.299530] sd 0:0:0:0: [sda] 78140160 512-byte logical blocks: (40.0 GB/37.2 GiB)
[    1.299617] sd 0:0:0:0: [sda] Write Protect is off
[    1.299622] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.299666] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.299915]  sda: sda1 sda2
[    1.392758] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.460449] ata2.00: ATAPI: UJDA760eDVD/CDRW, 1.03, max UDMA/33
[    1.476433] ata2.00: configured for UDMA/33
[    1.478172] scsi 1:0:0:0: CD-ROM            MATSHITA UJDA760eDVD/CDRW 1.03 PQ: 0 ANSI: 5
[    1.481344] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[    1.481350] Uniform CD-ROM driver Revision: 3.20
[    1.481476] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.481562] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    1.481640] Freeing unused kernel memory: 664k freed
[    1.483029] Write protecting the kernel text: 4704k
[    1.483069] Write protecting the kernel read-only data: 1848k
[    1.514989] udev: starting version 151
[    1.830627] sis900.c: v1.08.10 Apr. 2 2006
[    1.831044] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 4
[    1.831050] PCI: setting IRQ 4 as level-triggered
[    1.831057] sis900 0000:00:04.0: PCI INT A -> Link[LNKD] -> GSI 4 (level, low) -> IRQ 4
[    1.832514] 0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1.
[    1.844279] 0000:00:04.0: Using transceiver found at address 1 as default
[    1.852439] eth0: SiS 900 PCI Fast Ethernet at 0x1800, IRQ 4, 00:0d:5e:3c:f8:dc
[    1.852505] ohci1394 0000:00:0a.1: PCI INT B -> Link[LNKC] -> GSI 5 (level, low) -> IRQ 5
[    1.908108] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[5]  MMIO=[ec009000-ec0097ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[    2.081229] EXT4-fs (sda1): mounted filesystem with ordered data mode
[    3.180272] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00004ce0363cf8dc]
[    5.173333] Adding 984056k swap on /dev/sda2.  Priority:-1 extents:1 across:984056k
[    5.629630] udev: starting version 151
[    7.167953] Linux agpgart interface v0.103
[    7.329115] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x8100
[    7.397457] yenta_cardbus 0000:00:0a.0: CardBus bridge found [1033:8218]
[    7.397493] yenta_cardbus 0000:00:0a.0: Enabling burst memory read transactions
[    7.397500] yenta_cardbus 0000:00:0a.0: Using CSCINT to route CSC interrupts to PCI
[    7.397504] yenta_cardbus 0000:00:0a.0: Routing CardBus interrupts to PCI
[    7.397512] yenta_cardbus 0000:00:0a.0: TI: mfunc 0x002c1222, devctl 0x66
[    7.636497] yenta_cardbus 0000:00:0a.0: ISA IRQ mask 0x0840, PCI irq 10
[    7.636505] yenta_cardbus 0000:00:0a.0: Socket status: 30000086
[    7.637867] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    7.638229] agpgart-sis 0000:00:00.0: SiS chipset [1039/0740]
[    7.648754] lp: driver loaded but no devices found
[    7.658107] agpgart-sis 0000:00:00.0: AGP aperture is 64M @ 0xe8000000
[    7.764241] input: PS/2 Mouse as /devices/platform/i8042/serio1/input/input5
[    7.781398] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input6
[    7.885238] vga16fb: initializing
[    7.885250] vga16fb: mapped to 0xc00a0000
[    7.885526] fb0: VGA16 VGA frame buffer device
[    8.513923] Console: switching to colour frame buffer device 80x30
[    8.685676] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
[    8.687460] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean.
[    8.688296] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[    8.688957] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[    8.689853] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[    9.521829] Intel ICH 0000:00:02.7: PCI INT C -> Link[LNKC] -> GSI 5 (level, low) -> IRQ 5
[   10.448057] intel8x0_measure_ac97_clock: measured 55264 usecs (2658 samples)
[   10.448066] intel8x0: clocking to 48000
[   14.547074] eth0: Media Link Off
[   14.547193] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  115.546933] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  119.816063] ------------[ cut here ]------------
[  119.816115] WARNING: at /build/buildd/linux-2.6.32/net/sched/sch_generic.c:261 dev_watchdog+0x1fe/0x210()
[  119.816127] Hardware name: PC-LL350BD
[  119.816137] NETDEV WATCHDOG: eth0 (sis900): transmit queue 0 timed out
[  119.816146] Modules linked in: binfmt_misc snd_intel8x0 snd_ac97_codec ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy snd_seq_oss snd_seq_midi fbcon snd_rawmidi tileblit font bitblit softcursor snd_seq_midi_event pcmcia joydev snd_seq vga16fb vgastate snd_timer snd_seq_device lp snd soundcore sis_agp psmouse shpchp yenta_socket rsrc_nonstatic snd_page_alloc i2c_sis96x agpgart serio_raw parport pcmcia_core ohci1394 sis900 mii ieee1394
[  119.816284] Pid: 0, comm: swapper Not tainted 2.6.32-45-generic #99-Ubuntu
[  119.816295] Call Trace:
[  119.816324]  [<c014d2c2>] warn_slowpath_common+0x72/0xa0
[  119.816341]  [<c04dea0e>] ? dev_watchdog+0x1fe/0x210
[  119.816357]  [<c04dea0e>] ? dev_watchdog+0x1fe/0x210
[  119.816373]  [<c014d33b>] warn_slowpath_fmt+0x2b/0x30
[  119.816389]  [<c04dea0e>] dev_watchdog+0x1fe/0x210
[  119.816414]  [<c0164c60>] ? insert_work+0x60/0xb0
[  119.816438]  [<c012aa28>] ? default_spin_lock_flags+0x8/0x10
[  119.816461]  [<c0592a4f>] ? _spin_lock_irqsave+0x2f/0x50
[  119.816477]  [<c0164f26>] ? __queue_work+0x36/0x50
[  119.816493]  [<c015c6ae>] run_timer_softirq+0x13e/0x2c0
[  119.816510]  [<c04de810>] ? dev_watchdog+0x0/0x210
[  119.816526]  [<c01540a8>] __do_softirq+0x98/0x1b0
[  119.816542]  [<c012aa28>] ? default_spin_lock_flags+0x8/0x10
[  119.816558]  [<c0592a4f>] ? _spin_lock_irqsave+0x2f/0x50
[  119.816579]  [<c0106c87>] ? enable_8259A_irq+0x47/0x70
[  119.816621]  [<c0154205>] do_softirq+0x45/0x50
[  119.816634]  [<c0154355>] irq_exit+0x65/0x70
[  119.816650]  [<c0596ef5>] do_IRQ+0x55/0xc0
[  119.816667]  [<c016e855>] ? sched_clock_local+0xa5/0x180
[  119.816683]  [<c0103a30>] common_interrupt+0x30/0x40
[  119.816707]  [<c03a20bf>] ? acpi_idle_enter_simple+0x11a/0x148
[  119.816732]  [<c04a690a>] cpuidle_idle_call+0x7a/0x100
[  119.816746]  [<c01021c4>] cpu_idle+0x94/0xd0
[  119.816760]  [<c05800d2>] rest_init+0x62/0x70
[  119.816777]  [<c07ab8fb>] start_kernel+0x356/0x35c
[  119.816792]  [<c07ab3d1>] ? unknown_bootoption+0x0/0x19e
[  119.816808]  [<c07ab0aa>] i386_start_kernel+0xaa/0xb1
[  119.816819] ---[ end trace e965addd958d7956 ]---
[  119.816833] eth0: Transmit timeout, status 00000004 00000000
[  120.545258] eth0: Media Link On 100mbps full-duplex
[  126.528082] eth0: no IPv6 routers present
[ 1215.852126] usb 1-2: new high speed USB device using ehci_hcd and address 2
[ 1215.986491] usb 1-2: configuration #1 chosen from 1 choice
[ 1217.406238] Initializing USB Mass Storage driver...
[ 1217.407046] scsi2 : SCSI emulation for USB Mass Storage devices
[ 1217.408292] usbcore: registered new interface driver usb-storage
[ 1217.408301] USB Mass Storage support registered.
[ 1217.414955] usb-storage: device found at 2
[ 1217.414967] usb-storage: waiting for device to settle before scanning
[ 1222.412500] usb-storage: device scan complete
[ 1222.413441] scsi 2:0:0:0: Direct-Access     ELECOM   MF-LSU2          0.00 PQ: 0 ANSI: 2
[ 1222.420486] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 1222.422375] sd 2:0:0:0: [sdb] 7826551 512-byte logical blocks: (4.00 GB/3.73 GiB)
[ 1222.422978] sd 2:0:0:0: [sdb] Write Protect is off
[ 1222.422993] sd 2:0:0:0: [sdb] Mode Sense: 00 00 00 00
[ 1222.423004] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 1222.441740] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 1222.441768]  sdb: sdb1
[ 1222.590111] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 1222.590136] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 1287.995077] Disabling lock debugging due to kernel taint
[ 1288.008841] ndiswrapper version 1.55 loaded (smp=yes, preempt=no)
[ 1288.079543] usbcore: registered new interface driver ndiswrapper
[ 1343.288111] pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0
[ 1343.288233] pci 0000:02:00.0: reg 10 io port: [0x00-0x1f]
[ 1343.288258] pci 0000:02:00.0: reg 14 32bit mmio: [0x000000-0x00001f]
[ 1343.288283] pci 0000:02:00.0: reg 18 32bit mmio: [0x000000-0x0007ff]
[ 1343.288418] pci 0000:02:00.0: supports D2
[ 1343.380185] ndiswrapper: driver net2g54l (BUFFALO INC.,09/08/2004,2.27.09.2004) loaded
[ 1343.381135] ndiswrapper 0000:02:00.0: enabling device (0000 -> 0003)
[ 1343.381177] ndiswrapper 0000:02:00.0: PCI INT A -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10
[ 1343.388126] ndiswrapper 0000:02:00.0: setting latency timer to 64
[ 1343.588665] ndiswrapper: using IRQ 10
[ 1343.791468] wlan0: ethernet device 00:00:00:00:00:00 using NDIS driver: net2g54l, version: 0x2001b, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 17FE:2220.5.conf
[ 1343.791546] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK
[ 1347.579359] ADDRCONF(NETDEV_UP): wlan0: link is not ready


--lsmod--
Module                  Size  Used by
ndiswrapper           184709  0
usb_storage            40033  1
binfmt_misc             6587  1
snd_intel8x0           25652  0
snd_ac97_codec        100646  1 snd_intel8x0
ac97_bus                1002  1 snd_ac97_codec
snd_pcm_oss            35308  0
snd_mixer_oss          13746  1 snd_pcm_oss
snd_pcm                70694  3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_seq_dummy           1338  0
snd_seq_oss            26722  0
snd_seq_midi            4557  0
fbcon                  35102  71
snd_rawmidi            19056  1 snd_seq_midi
tileblit                1999  1 fbcon
font                    7557  1 fbcon
bitblit                 4707  1 fbcon
softcursor              1189  1 bitblit
snd_seq_midi_event      6003  2 snd_seq_oss,snd_seq_midi
pcmcia                 30784  0
joydev                  8740  0
snd_seq                47263  6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
vga16fb                11385  1
vgastate                8961  1 vga16fb
snd_timer              19130  2 snd_pcm,snd_seq
snd_seq_device          5700  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
lp                      7028  0
snd                    54244  10 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore               6620  1 snd
sis_agp                 4015  1
psmouse                63677  0
shpchp                 28835  0
yenta_socket           20408  2
rsrc_nonstatic         10015  1 yenta_socket
snd_page_alloc          7076  2 snd_intel8x0,snd_pcm
i2c_sis96x              3024  0
agpgart                31724  1 sis_agp
serio_raw               3978  0
parport                32635  1 lp
pcmcia_core            32964  3 pcmcia,yenta_socket,rsrc_nonstatic
ohci1394               26950  0
sis900                 17048  0
mii                     4381  1 sis900
ieee1394               81181  1 ohci1394


--lspci--
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 740 Host (rev 01)
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual PCI-to-PCI bridge (AGP)
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS962 [MuTIOL Media IO] (rev 25)
00:02.1 SMBus: Silicon Integrated Systems [SiS] SiS961/2 SMBus Controller
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE]
00:02.6 Modem: Silicon Integrated Systems [SiS] AC'97 Modem Controller (rev a0)
00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] AC'97 Sound Controller (rev a0)
00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller
00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet (rev 91)
00:0a.0 CardBus bridge: Texas Instruments PCI4510 PC card Cardbus Controller (rev 02)
00:0a.1 FireWire (IEEE 1394): Texas Instruments PCI4510 IEEE-1394 Controller
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 65x/M650/740 PCI/AGP VGA Display Adapter
02:00.0 Ethernet controller: Linksys, A Division of Cisco Systems [AirConn] INPROCOMM IPN 2220 Wireless LAN Adapter (rev 01)


02:00.0 Ethernet controller [0200]: Linksys, A Division of Cisco Systems [AirConn] INPROCOMM IPN 2220 Wireless LAN Adapter (rev 01) [17fe:2220]
    Subsystem: Melco Inc Device [1154:0334]
    Flags: bus master, medium devsel, latency 64, IRQ 10
    I/O ports at 1c00 [size=32]
    Memory at 14000800 (32-bit, non-prefetchable) [size=32]
    Memory at 14000000 (32-bit, non-prefetchable) [size=2K]
    Capabilities: <access denied>
    Kernel driver in use: ndiswrapper