Ubuntu日本語フォーラム

RxOrca · 2008-02-12 20:27:41

ノート PCに CardBusな eSATAインターフェースカードを挿して使ってみたです。
I-O DATAの CBESAで, チップは Sil3512 … なのカモ。

だけど, 自動マウントができなかったりするです。
なので gnome-mount -d /dev/sdb1 とか指定してみたです。

自動マウント以外は大丈夫っぽくて, 速度は約 65 MB/sec (時々 72とか 73とか)
ローカル HDDの倍くらいだったり。

んで, ログです。

コード:

$ dmesg | grep -i -e cardbus -e pcmcia -e sata
[    5.169504] PCI: Bus 3, cardbus bridge: 0000:02:00.0
[    5.169532] PCI: Bus 7, cardbus bridge: 0000:02:00.1
[   19.444000] Yenta: CardBus bridge found at 0000:02:00.0 [1014:023b]
[   19.444000] Yenta: Routing CardBus interrupts to PCI
[   19.676000] pcmcia: parent PCI bridge I/O window: 0x2000 - 0x6fff
[   19.676000] pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff
[   19.676000] pcmcia: parent PCI bridge Memory window: 0xf0000000 - 0xf7ffffff
[   19.676000] Yenta: CardBus bridge found at 0000:02:00.1 [1014:023b]
[   19.676000] Yenta: Routing CardBus interrupts to PCI
[   19.908000] pcmcia: parent PCI bridge I/O window: 0x2000 - 0x6fff
[   19.908000] pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff
[   19.908000] pcmcia: parent PCI bridge Memory window: 0xf0000000 - 0xf7ffffff
[   20.544000] pccard: CardBus card inserted into slot 1
[   22.024000] sata_sil 0000:07:00.0: version 2.2
[   22.024000] sata_sil 0000:07:00.0: cache line size not set.  Driver may not function
[   22.024000] sata_sil 0000:07:00.0: Applying R_ERR on DMA activate FIS errata fix
[   22.024000] scsi2 : sata_sil
[   22.024000] scsi3 : sata_sil
[   22.024000] ata3: SATA max UDMA/100 cmd 0xf09b4080 ctl 0xf09b408a bmdma 0xf09b4000 irq 11
[   22.024000] ata4: SATA max UDMA/100 cmd 0xf09b40c0 ctl 0xf09b40ca bmdma 0xf09b4008 irq 11
[   22.336000] ata3: SATA link down (SStatus 0 SControl 310)
[   22.688000] ata4: SATA link down (SStatus 0 SControl 310)

で, 最後の方 (接続したとき)

コード:

[ 2164.888000] ata3: exception Emask 0x10 SAct 0x0 SErr 0x50000 action 0x2 frozen
[ 2164.888000] ata3: hard resetting port
[ 2165.768000] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2165.788000] ata3.00: ATA-8: WDC WD5000AAKS-00YGA0, 12.01C02, max UDMA/133
[ 2165.788000] ata3.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 2165.804000] ata3.00: configured for UDMA/100
[ 2165.804000] ata3: EH complete
[ 2165.804000] scsi 2:0:0:0: Direct-Access     ATA      WDC WD5000AAKS-0 12.0 PQ: 0 ANSI: 5
[ 2165.808000] sd 2:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
[ 2165.808000] sd 2:0:0:0: [sdb] Write Protect is off
[ 2165.808000] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2165.808000] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2165.808000] sd 2:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
[ 2165.808000] sd 2:0:0:0: [sdb] Write Protect is off
[ 2165.808000] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2165.808000] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2165.808000]  sdb: sdb1
[ 2165.816000] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 2165.816000] sd 2:0:0:0: Attached scsi generic sg1 type 0

Ubuntu日本語フォーラム

お知らせ

#1 2008-02-12 20:27:41

CardBusの eSATAインターフェースカード

コード:

コード:

Board footer