Ubuntu日本語フォーラム

Aomapesu · 2007-08-31 19:18:12

Eigo de kaite moushiwakegozaimasen.

I am having problem to install the ISDN modem Aterm IT21L in USB on my Dapper Drake.

I leave in Kobuchizawa, Yamanashiken, and the only internet access available is ISDN at 64kbps.

I have installed the modem on my XP but I really need to use Ubuntu !

So I have 2 problems:
1 - When I use Ubuntu the modem doesn't seem to be recognized (no red light on)

2 - I went through System->Administration->Network to setup the connexion but I don't know how to go further than that when the modem will be recognized..

I would be very grateful if someone could help me ?

Osewani narimasu.

hito · 2007-08-31 22:08:01

Please give us your lsusb output on terminal..

コード:

$ sudo lsusb -v

Aomapesu · 2007-08-31 23:21:19

lsusb -v command gives:

コード:

Bus 001 Device 002: ID 0409:0012 NEC Corp. ATerm IT75DSU ISDN TA
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.00
  bDeviceClass          255 Vendor Specific Class
  bDeviceSubClass         0
  bDeviceProtocol       255
  bMaxPacketSize0         8
  idVendor           0x0409 NEC Corp.
  idProduct          0x0012 ATerm IT75DSU ISDN TA
  bcdDevice            1.00
  iManufacturer           0
  iProduct                0
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           83
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0x60
      (Missing must-be-set bit!)
      Self Powered
      Remote Wakeup
    MaxPower               10mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           4
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass      0
      bInterfaceProtocol    255
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x03  EP 3 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x84  EP 4 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       1
      bNumEndpoints           4
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass      0
      bInterfaceProtocol    255
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x03  EP 3 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x84  EP 4 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval               0
Device Status:     0x0001
  Self Powered

Bus 001 Device 001: ID 0000:0000
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x0000
  idProduct          0x0000
  bcdDevice            2.06
  iManufacturer           3 Linux 2.6.15-28-386 uhci_hcd
  iProduct                2 UHCI Host Controller
  iSerial                 1 0000:00:05.2
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xc0
      Self Powered
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             2
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood        1 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x60
  PortPwrCtrlMask    0xc1
 Hub Port Status:
   Port 1: 0000.0103 power enable connect
   Port 2: 0000.0100 power
Device Status:     0x0001
  Self Powered

Aomapesu · 2007-09-01 23:32:56

NIHONGO DEMO II DESU YO !

a, wasuretan dakedo, moshi nihongode kotaetai no dattara, zenzen kamawanainode, zehi nihongo demo, eigo demo onegaishimasu.
Ware ware no mondai o nihongo de setsumei shitehoshii no de areba, mata nihongo de kakinaoshimasu node, yoroshiku onegai shimasu !!!!

(nihongo no môji ga yomemasu ga, kompyuta de ha kakenai no desu)

hito · 2007-09-02 17:24:11

It might not go well...

1) install gnome-ppp
sudo aptitude install gnome-ppp

2) execute gnome-ppp
sudo gnome-ppp

3) setup
Click [Setup] button. and click "Detect". If gnome-ppp not detect automatic,
please check your dmesg output(/var/log/dmesg).

4) change device type
"Type:" combobox require "USB Modem" or "IDSN Modem",
but I dont know ATerm's device type.
Please test both settings.

5) fill ISP settings
fill "Username", "Password", "Phone number".

6) test
Click [Connect] button.

When you cant connect, please paset your "Connection Log".

Aomapesu · 2007-09-02 22:40:44

Dear hito,

I have followed your instructions and installed gnome-ppp.
When I go in gnome-ppp and try to detect either a regular modem, USB modem or ISDN modem, nothing is detected...

Althought the Aterm is detected as an USB device (as shown in lsusb) it apparently is not recognized as a modem...

Here is my /var/log/dmesg/ and it does not show the Aterm at all... :(

コード:

[17179569.184000] Linux version 2.6.15-28-386 (buildd@terranova) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 PREEMPT Wed Jul 18 22:50:32 UTC 2007
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[17179569.184000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[17179569.184000]  BIOS-e820: 00000000000e8000 - 00000000000e8640 (reserved)
[17179569.184000]  BIOS-e820: 00000000000e8640 - 00000000000e8840 (ACPI NVS)
[17179569.184000]  BIOS-e820: 00000000000e8840 - 00000000000ec000 (reserved)
[17179569.184000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[17179569.184000]  BIOS-e820: 0000000000100000 - 0000000013fe0000 (usable)
[17179569.184000]  BIOS-e820: 0000000013fe0000 - 0000000013ff0000 (ACPI data)
[17179569.184000]  BIOS-e820: 0000000013ff0000 - 0000000014000000 (reserved)
[17179569.184000]  BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[17179569.184000] 0MB HIGHMEM available.
[17179569.184000] 319MB LOWMEM available.
[17179569.184000] On node 0 totalpages: 81888
[17179569.184000]   DMA zone: 4096 pages, LIFO batch:0
[17179569.184000]   DMA32 zone: 0 pages, LIFO batch:0
[17179569.184000]   Normal zone: 77792 pages, LIFO batch:15
[17179569.184000]   HighMem zone: 0 pages, LIFO batch:0
[17179569.184000] DMI 2.3 present.
[17179569.184000] ACPI: RSDP (v000 TOSHIB                                ) @ 0x000f01a0
[17179569.184000] ACPI: RSDT (v001 TOSHIB 750      0x00970814 TASM 0x04010000) @ 0x13fe0000
[17179569.184000] ACPI: FADT (v001 TOSHIB 750      0x00970814 TASM 0x04010000) @ 0x13fe0054
[17179569.184000] ACPI: DSDT (v001 TOSHIB 4220     0x19991106 MSFT 0x0100000a) @ 0x00000000
[17179569.184000] ACPI: BIOS age (1999) fails cutoff (2000), acpi=force is required to enable ACPI
[17179569.184000] ACPI: Disabling ACPI support
[17179569.184000] Allocating PCI resources starting at 20000000 (gap: 14000000:ebf80000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: root=/dev/hda2 ro quiet splash vga=791
[17179569.184000] Local APIC disabled by BIOS (or by default) -- you can enable it with "lapic"
[17179569.184000] mapped APIC to ffffd000 (01282000)
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 2048 (order: 11, 32768 bytes)
[    0.000000] Detected 746.440 MHz processor.
[ 1141.366427] Using tsc for high-res timesource
[ 1141.366489] Console: colour dummy device 80x25
[ 1141.367923] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 1141.369650] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 1141.409773] Memory: 314036k/327552k available (1977k kernel code, 12888k reserved, 605k data, 288k init, 0k highmem)
[ 1141.409784] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 1141.486388] Calibrating delay using timer specific routine.. 1494.63 BogoMIPS (lpj=2989264)
[ 1141.486464] Security Framework v1.0.0 initialized
[ 1141.486484] SELinux:  Disabled at boot.
[ 1141.486517] Mount-cache hash table entries: 512
[ 1141.486731] CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
[ 1141.486748] CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
[ 1141.486769] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 1141.486776] CPU: L2 cache: 256K
[ 1141.486783] CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000
[ 1141.486819] mtrr: v2.0 (20020519)
[ 1141.486831] CPU: Intel Pentium III (Coppermine) stepping 0a
[ 1141.486841] Enabling fast FPU save and restore... done.
[ 1141.486847] Enabling unmasked SIMD FPU exception support... done.
[ 1141.486857] Checking 'hlt' instruction... OK.
[ 1141.502807] checking if image is initramfs... it is
[ 1143.534955] Freeing initrd memory: 6617k freed
[ 1143.579095] NET: Registered protocol family 16
[ 1143.579178] EISA bus registered
[ 1143.580614] PCI: PCI BIOS revision 2.10 entry at 0xfedcd, last bus=21
[ 1143.580632] PCI: Using configuration type 1
[ 1143.581651] ACPI: Subsystem revision 20051216
[ 1143.581658] ACPI: Interpreter disabled.
[ 1143.581666] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 1143.581683] pnp: PnP ACPI: disabled
[ 1143.581692] PnPBIOS: Scanning system for PnP BIOS support...
[ 1143.581796] PnPBIOS: Found PnP BIOS installation structure at 0xc00f90b0
[ 1143.581805] PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x9520, dseg 0x0
[ 1143.666515] PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
[ 1143.666555] PCI: Probing PCI hardware
[ 1143.666565] PCI: Probing PCI hardware (bus 00)
[ 1143.666932] PCI quirk: region fe00-fe3f claimed by PIIX4 ACPI
[ 1143.666942] PCI quirk: region fe70-fe7f claimed by PIIX4 SMB
[ 1143.666952] PIIX4 devres B PIO at 006c-006f
[ 1143.667324] Boot video device is 0000:01:00.0
[ 1143.668920] PCI: Using IRQ router PIIX/ICH [8086/7110] at 0000:00:05.0
[ 1143.668948] PCI: IRQ 0 for device 0000:00:0b.0 doesn't match PIRQ mask - try pci=usepirqmask
[ 1143.668958] PCI: Found IRQ 11 for device 0000:00:0b.0
[ 1143.668979] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 1143.668988] PCI: IRQ 0 for device 0000:00:0b.1 doesn't match PIRQ mask - try pci=usepirqmask
[ 1143.668997] PCI: Found IRQ 11 for device 0000:00:0b.1
[ 1143.669016] PCI: Sharing IRQ 11 with 0000:00:0c.0
[ 1143.683485] PCI: Bridge: 0000:00:01.0
[ 1143.683492]   IO window: disabled.
[ 1143.683501]   MEM window: fec00000-ff7fffff
[ 1143.683510]   PREFETCH window: 28000000-280fffff
[ 1143.683519] PCI: Bus 2, cardbus bridge: 0000:00:0b.0
[ 1143.683525]   IO window: 00001000-000010ff
[ 1143.683533]   IO window: 00001400-000014ff
[ 1143.683542]   PREFETCH window: 20000000-21ffffff
[ 1143.683550]   MEM window: 22000000-23ffffff
[ 1143.683558] PCI: Bus 6, cardbus bridge: 0000:00:0b.1
[ 1143.683564]   IO window: 00001800-000018ff
[ 1143.683572]   IO window: 00001c00-00001cff
[ 1143.683581]   PREFETCH window: 24000000-25ffffff
[ 1143.683589]   MEM window: 26000000-27ffffff
[ 1143.683621] PCI: Found IRQ 11 for device 0000:00:0b.0
[ 1143.683642] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 1143.683664] PCI: Found IRQ 11 for device 0000:00:0b.1
[ 1143.683683] PCI: Sharing IRQ 11 with 0000:00:0c.0
[ 1143.684719] audit: initializing netlink socket (disabled)
[ 1143.684744] audit(1188745519.288:1): initialized
[ 1143.685012] VFS: Disk quotas dquot_6.5.1
[ 1143.685071] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1143.685197] Initializing Cryptographic API
[ 1143.685208] io scheduler noop registered
[ 1143.685223] io scheduler anticipatory registered
[ 1143.685238] io scheduler deadline registered
[ 1143.685261] io scheduler cfq registered
[ 1143.685272] Limiting direct PCI/PCI transfers.
[ 1143.685670] isapnp: Scanning for PnP cards...
[ 1144.038287] isapnp: No Plug & Play device found
[ 1144.079079] PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
[ 1144.081416] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1144.081626] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1144.081718] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
[ 1144.081918] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1144.087957] 00:0e: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1144.089291] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 1144.089406] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 1144.089416] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 1144.089758] mice: PS/2 mouse device common for all mice
[ 1144.090211] EISA: Probing bus 0 at eisa.0
[ 1144.090226] Cannot allocate resource for EISA slot 1
[ 1144.090253] EISA: Detected 0 cards.
[ 1144.090355] NET: Registered protocol family 2
[ 1144.114090] input: AT Translated Set 2 keyboard as /class/input/input0
[ 1144.132666] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 1144.133003] TCP established hash table entries: 16384 (order: 4, 65536 bytes)
[ 1144.133241] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 1144.133488] TCP: Hash tables configured (established 16384 bind 16384)
[ 1144.133496] TCP reno registered
[ 1144.133703] TCP bic registered
[ 1144.133728] NET: Registered protocol family 1
[ 1144.133745] NET: Registered protocol family 8
[ 1144.133751] NET: Registered protocol family 20
[ 1144.133799] Using IPI Shortcut mode
[ 1144.133895] Freeing unused kernel memory: 288k freed
[ 1144.263677] vesafb: framebuffer at 0xff400000, mapped to 0xd4880000, using 2560k, total 2560k
[ 1144.263690] vesafb: mode is 1024x768x16, linelength=2048, pages=0
[ 1144.263698] vesafb: protected mode interface info at c000:6edc
[ 1144.263703] vesafb: scrolling: redraw
[ 1144.263710] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 1144.263718] vesafb: Mode is VGA compatible
[ 1144.330282] Console: switching to colour frame buffer device 128x48
[ 1144.330295] fb0: VESA VGA frame buffer device
[ 1145.449844] Capability LSM initialized
[ 1146.753130] PIIX4: IDE controller at PCI slot 0000:00:05.1
[ 1146.753164] PIIX4: chipset revision 1
[ 1146.753171] PIIX4: not 100% native mode: will probe irqs later
[ 1146.753191]     ide0: BM-DMA at 0xfff0-0xfff7, BIOS settings: hda:DMA, hdb:pio
[ 1146.753225]     ide1: BM-DMA at 0xfff8-0xffff, BIOS settings: hdc:DMA, hdd:pio
[ 1146.753246] Probing IDE interface ide0...
[ 1147.038643] hda: SAMSUNG MP0402H, ATA DISK drive
[ 1147.710282] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 1147.710655] Probing IDE interface ide1...
[ 1148.445651] hdc: TOSHIBA DVD-ROM SD-C2502, ATAPI CD/DVD-ROM drive
[ 1149.137132] ide1 at 0x170-0x177,0x376 on irq 15
[ 1149.153823] hda: max request size: 1024KiB
[ 1149.610559] hda: 78242976 sectors (40060 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(33)
[ 1149.611001] hda: cache flushes supported
[ 1149.611404]  hda: hda1 hda2 hda3 < hda5 >
[ 1149.665903] hdc: ATAPI 24X DVD-ROM drive, 128kB Cache, UDMA(33)
[ 1149.665926] Uniform CD-ROM driver Revision: 3.20
[ 1150.057039] usbcore: registered new driver usbfs
[ 1150.057872] usbcore: registered new driver hub
[ 1150.063124] USB Universal Host Controller Interface driver v2.3
[ 1150.063978] PCI: Found IRQ 11 for device 0000:00:05.2
[ 1150.064025] uhci_hcd 0000:00:05.2: UHCI Host Controller
[ 1150.065054] uhci_hcd 0000:00:05.2: new USB bus registered, assigned bus number 1
[ 1150.065079] uhci_hcd 0000:00:05.2: irq 11, io base 0x0000ff80
[ 1150.065782] hub 1-0:1.0: USB hub found
[ 1150.065819] hub 1-0:1.0: 2 ports detected
[ 1150.261234] Attempting manual resume
[ 1150.313847] EXT3-fs: mounted filesystem with ordered data mode.
[ 1150.340368] kjournald starting.  Commit interval 5 seconds
[ 1150.408184] usb 1-1: new full speed USB device using uhci_hcd and address 2
[ 1166.104410] PCI: Found IRQ 11 for device 0000:00:0b.0
[ 1166.104442] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 1166.104461] Yenta: CardBus bridge found at 0000:00:0b.0 [1179:0001]
[ 1166.148314] Linux agpgart interface v0.101 (c) Dave Jones
[ 1166.166739] piix4_smbus 0000:00:05.3: Found 0000:00:05.3 device
[ 1166.178341] agpgart: Detected an Intel 440BX Chipset.
[ 1166.194371] agpgart: AGP aperture is 256M @ 0xe0000000
[ 1166.229893] Yenta: ISA IRQ mask 0x04b8, PCI irq 11
[ 1166.229905] Socket status: 30000007
[ 1166.230430] PCI: Found IRQ 11 for device 0000:00:0b.1
[ 1166.230455] PCI: Sharing IRQ 11 with 0000:00:0c.0
[ 1166.230484] Yenta: CardBus bridge found at 0000:00:0b.1 [1179:0001]
[ 1166.357905] Yenta: ISA IRQ mask 0x04b8, PCI irq 11
[ 1166.357916] Socket status: 30000020
[ 1166.449452] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1166.460398] input: PC Speaker as /class/input/input1
[ 1166.500345] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 1166.559161] irda_init()
[ 1166.559197] NET: Registered protocol family 23
[ 1166.588723] PCI: Found IRQ 11 for device 0000:00:09.0
[ 1166.588905] IrDA: Registered device irda0
[ 1166.588912] toshoboe: Using multiple tasks, version $Id: donauboe.c V2.18 ven jan 10 03:14:16 2003$
[ 1166.904659] spurious 8259A interrupt: IRQ7.
[ 1167.008546] pccard: CardBus card inserted into slot 1
[ 1167.273367] Real Time Clock Driver v1.12
[ 1167.569231] Floppy drive(s): fd0 is 1.44M
[ 1167.587347] FDC 0 is an 8272A
[ 1167.785930] input: ImPS/2 Generic Wheel Mouse as /class/input/input2
[ 1168.191402] PCI: Found IRQ 11 for device 0000:00:0c.0
[ 1168.191431] PCI: Sharing IRQ 11 with 0000:00:0b.1
[ 1168.205879] parport: PnPBIOS parport detected.
[ 1168.205940] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 1168.530352] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[ 1168.650580] cs: IO port probe 0x100-0x3af: clean.
[ 1168.651439] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 1168.651809] cs: IO port probe 0x820-0x8ff: clean.
[ 1168.652129] cs: IO port probe 0xc00-0xcf7: clean.
[ 1168.652636] cs: IO port probe 0xa00-0xaff: clean.
[ 1168.654628] cs: IO port probe 0x100-0x3af: clean.
[ 1168.655489] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 1168.655857] cs: IO port probe 0x820-0x8ff: clean.
[ 1168.656177] cs: IO port probe 0xc00-0xcf7: clean.
[ 1168.656685] cs: IO port probe 0xa00-0xaff: clean.
[ 1169.054351] PCI: Enabling device 0000:06:00.0 (0000 -> 0002)
[ 1169.054397] PCI: Setting latency timer of device 0000:06:00.0 to 64
[ 1169.054406] ohci_hcd 0000:06:00.0: OHCI Host Controller
[ 1169.054828] ohci_hcd 0000:06:00.0: new USB bus registered, assigned bus number 2
[ 1169.054850] ohci_hcd 0000:06:00.0: irq 11, io mem 0x26000000
[ 1169.137585] hub 2-0:1.0: USB hub found
[ 1169.137616] hub 2-0:1.0: 1 port detected
[ 1169.200103] ts: Compaq touchscreen protocol output
[ 1169.239251] PCI: Enabling device 0000:06:00.1 (0000 -> 0002)
[ 1169.239297] PCI: Setting latency timer of device 0000:06:00.1 to 64
[ 1169.239306] ohci_hcd 0000:06:00.1: OHCI Host Controller
[ 1169.239397] ohci_hcd 0000:06:00.1: new USB bus registered, assigned bus number 3
[ 1169.239419] ohci_hcd 0000:06:00.1: irq 11, io mem 0x26001000
[ 1169.325071] hub 3-0:1.0: USB hub found
[ 1169.325101] hub 3-0:1.0: 1 port detected
[ 1170.136978] PCI: Enabling device 0000:06:00.2 (0000 -> 0002)
[ 1170.137025] ehci_hcd 0000:06:00.2: EHCI Host Controller
[ 1170.158768] ehci_hcd 0000:06:00.2: new USB bus registered, assigned bus number 4
[ 1170.158795] ehci_hcd 0000:06:00.2: irq 11, io mem 0x26002000
[ 1170.158816] ehci_hcd 0000:06:00.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 1170.159420] hub 4-0:1.0: USB hub found
[ 1170.159451] hub 4-0:1.0: 2 ports detected
[ 1171.124003] lp0: using parport0 (interrupt-driven).
[ 1171.270571] Adding 939760k swap on /dev/hda5.  Priority:-1 extents:1 across:939760k
[ 1171.398054] EXT3 FS on hda2, internal journal
[ 1171.744341] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[ 1171.744353] md: bitmap version 4.39
[ 1172.410325] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [email protected]
[ 1173.252731] cdrom: open failed.
[ 1174.013175] NTFS driver 2.1.25 [Flags: R/O MODULE].
[ 1174.102722] NTFS volume version 3.1.
[ 1176.372657] NET: Registered protocol family 17

Since with lsusb we know where my modem is do you think there is a way to force Ubuntu to recognized an USB device as an ISDN modem ?

Thank you very much for your help !

hito · 2007-09-03 20:24:03

Dear Aomapesu,

lsusb said:

コード:

      bInterfaceClass       255 Vendor Specific Class

and, dmesg does not detect ATerm, so I think that this is the "winmodem" in USB-mode.
It require vendor specific driver. But I cant found it.

Since with lsusb we know where my modem is do you think there is a way to force Ubuntu to recognized
an USB device as an ISDN modem ?

I think that it is impossible or too dificulty.

However, this modem has RS-232C port, it is generic device(maybe).
http://121ware.com/product/atermstation/product/terminal/it31l/index.html

Please test with RS-232C port....

Aomapesu · 2007-09-03 23:13:54

Hito you really are great.

The modem is detected in RS-232C port as shown by a magnificent green light next to the "ready" sign on the Aterm.

BUT it still cannot connect to the internet although I have specified correctly my ISP settings

Here is how it goes under gnome-ppp:
Detecting (ready light turns green on modem)

コード:

WVCONF: /root/.wvdial.conf
GNOME PPP: STDOUT: Editing `/dev/null'.
GNOME PPP: STDOUT:
GNOME PPP: STDOUT: Scanning your serial ports for a modem.
GNOME PPP: STDOUT:
GNOME PPP: STDERR: ttyS0<*1>: ATQ0 V1 E1 -- OK
GNOME PPP: STDERR: ttyS0<*1>: ATQ0 V1 E1 Z -- OK
GNOME PPP: STDERR: ttyS0<*1>: ATQ0 V1 E1 S0=0 -- OK
GNOME PPP: STDERR: ttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
GNOME PPP: STDERR: ttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
GNOME PPP: STDERR: ttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- ERROR
GNOME PPP: STDERR: ttyS0<*1>: Modem Identifier: ATI -- 960
GNOME PPP: STDERR: ttyS0<*1>: Speed 4800: AT -- OK
GNOME PPP: STDERR: ttyS0<*1>: Speed 9600: AT -- OK
GNOME PPP: STDERR: ttyS0<*1>: Speed 19200: AT -- OK
GNOME PPP: STDERR: ttyS0<*1>: Speed 38400: AT -- OK
GNOME PPP: STDERR: ttyS0<*1>: Speed 57600: AT -- OK
GNOME PPP: STDERR: ttyS0<*1>: Speed 115200: AT -- OK
GNOME PPP: STDERR: ttyS0<*1>: Max speed is 115200; that should be safe.
GNOME PPP: STDERR: ttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
GNOME PPP: STDOUT:
GNOME PPP: STDERR: Modem Port Scan<*1>: S2   S3   S4   S5   S6   S7   S8   S9
GNOME PPP: STDOUT: Found a modem on /dev/ttyS0.
GNOME PPP: STDERR: Modem Port Scan<*1>: S10  S11  S12  S13  S14  S15  S16  S17
GNOME PPP: STDOUT: Modem configuration written to /dev/null.
GNOME PPP: STDERR: Modem Port Scan<*1>: S18  S19  S20  S21  S22  S23  S24  S25
GNOME PPP: STDERR: Modem Port Scan<*1>: S26  S27  S28  S29  S30  S31  S32  S33
GNOME PPP: STDERR: Modem Port Scan<*1>: S34  S35  S36  S37  S38  S39  S40  S41
GNOME PPP: STDERR: Modem Port Scan<*1>: S42  S43  S44  S45  S46  S47
GNOME PPP: STDERR: ttyS0<Info>: Speed 115200; init "ATQ0 V1 E1 S0=0 &C1 &D2"

But it does not connect (here is the connection log)

コード:

GNOME PPP: Connexion en cours...
GNOME PPP: STDERR: --> Ignoring malformed input line: ";Do NOT edit this file by hand!"
GNOME PPP: STDERR: --> WvDial: Internet dialer version 1.55
GNOME PPP: STDERR: --> Initializing modem.
GNOME PPP: STDERR: --> Sending: ATZ
GNOME PPP: STDERR: ATZ
GNOME PPP: STDERR: OK
GNOME PPP: STDERR: --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
GNOME PPP: STDERR: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
GNOME PPP: STDERR: ERROR
GNOME PPP: STDERR: --> Bad init string.
GNOME PPP: STDERR: --> Initializing modem.
GNOME PPP: STDERR: --> Sending: ATZ
GNOME PPP: STDERR: ATZ
GNOME PPP: STDERR: OK
GNOME PPP: STDERR: --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
GNOME PPP: STDERR: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
GNOME PPP: STDERR: ERROR
GNOME PPP: STDERR: --> Bad init string.
GNOME PPP: STDERR: --> Initializing modem.
GNOME PPP: STDERR: --> Sending: ATZ
GNOME PPP: STDERR: ATZ
GNOME PPP: STDERR: OK
GNOME PPP: STDERR: --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
GNOME PPP: STDERR: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
GNOME PPP: STDERR: ERROR
GNOME PPP: STDERR: --> Bad init string.

One weird thing though it keeps detecting the modem as a regular one and does not take it as an ISDN device.

And although we see that in the detecting process it comes to an error in the following line

GNOME PPP: STDERR: ttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- ERROR

it is surprising that it still tries to send that particular string to the modem rather than sending the seemingly safe one

GNOME PPP: STDERR: ttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2

without the +FCLASS ending...

I am very grateful to you for all the effort you put in here. Hopefully we will get through it soon !

最後の編集者: Aomapesu (2007-09-04 19:19:24)

Aomapesu · 2007-09-06 02:50:57

Konbanha...

I finally found how to change the init chain in gnome-ppp (parameters->Init Chain) back to the one that can initialize the Aterm.

The problem know is that I can not connect to the internet.
It tells me that there is an "Invalid dial command":

コード:

WVCONF: /root/.wvdial.conf
GNOME PPP: Connexion en cours...
GNOME PPP: STDERR: --> Ignoring malformed input line: ";Do NOT edit this file by hand!"
GNOME PPP: STDERR: --> WvDial: Internet dialer version 1.55
GNOME PPP: STDERR: --> Initializing modem.
GNOME PPP: STDERR: --> Sending: ATZ
GNOME PPP: STDERR: ATZ
GNOME PPP: STDERR: OK
GNOME PPP: STDERR: --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2
GNOME PPP: STDERR: ATQ0 V1 E1 S0=0 &C1 &D2
GNOME PPP: STDERR: OK
GNOME PPP: STDERR: --> Modem initialized.
GNOME PPP: STDERR: --> Sending: AT1492
GNOME PPP: STDERR: --> Waiting for carrier.
GNOME PPP: STDERR: AT1492
GNOME PPP: STDERR: ERROR
GNOME PPP: STDERR: --> Invalid dial command.
GNOME PPP: STDERR: --> Disconnecting at Wed Sep  6 03:24:49 2007

1492 is the correct phone number that has been given to me by my ISP and it is the number that is getting me on the internet through windows...

If you have any idea how to solve that problem, I would be glad to read from you.

Dewa matta...

hito · 2007-09-07 10:20:52

Dear Aomapesu

I guess that this is AT commands problem.

The Aterm said "Invalid dial command", because it could not understood
generic AT commands. We have to send valid specified commands.

Can you check your TA's manuals or CD-ROMs?
If you found a AT commands commandset lists, please input them.

When you cant find these items, please wait several days, I'l seek
ATerm's AT commands in vendor's web page (I found manual PDF.
But Im in busy, so it is not possible to promise...).

Aomapesu · 2007-09-08 18:44:17

Hito san,

I think I found the AT command for this modem BUT a NEW problem arose ... :(

As you can see from this connection log (here with gnome-ppp):

コード:

~$ sudo gnome-ppp
WVCONF: /root/.wvdial.conf
GNOME PPP: Connexion en cours...
GNOME PPP: STDERR: --> Ignoring malformed input line: ";Do NOT edit this file by hand!"
GNOME PPP: STDERR: --> WvDial: Internet dialer version 1.55
GNOME PPP: STDERR: --> Initializing modem.
GNOME PPP: STDERR: --> Sending: ATZ
GNOME PPP: STDERR: ATZ
GNOME PPP: STDERR: OK
GNOME PPP: STDERR: --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2
GNOME PPP: STDERR: ATQ0 V1 E1 S0=0 &C1 &D2
GNOME PPP: STDERR: OK
GNOME PPP: STDERR: --> Sending: ATW
GNOME PPP: STDERR: ATW
GNOME PPP: STDERR: OK
GNOME PPP: STDERR: --> Modem initialized.
GNOME PPP: STDERR: --> Sending: ATDT1492
GNOME PPP: STDERR: --> Waiting for carrier.
GNOME PPP: STDERR: ATDT1492
GNOME PPP: STDERR: CONNECT 64000
GNOME PPP: STDERR: --> Carrier detected.  Starting PPP immediately.
GNOME PPP: STDERR: --> Starting pppd at Sat Sep  8 10:46:39 2007
GNOME PPP: STDERR: --> Pid of pppd: 6252
GNOME PPP: STDERR: --> Using interface ppp0
GNOME PPP: STDERR: --> pppd: ï¿½ï¿½[05][08]Xï¿½[05][08]xï¿½[05][08]ï¿½[12][06][08]Pï¿½[05][08]pï¿½[05][08]ï¿½ï¿½[05][08]

(gnome-ppp:6247): Gtk-CRITICAL **: gtk_text_buffer_emit_insert: assertion `g_utf8_validate (text, len, NULL)' failed
GNOME PPP: STDERR: --> pppd: ï¿½ï¿½[05][08]Xï¿½[05][08]xï¿½[05][08]ï¿½[12][06][08]Pï¿½[05][08]pï¿½[05][08]ï¿½ï¿½[05][08]

(gnome-ppp:6247): Gtk-CRITICAL **: gtk_text_buffer_emit_insert: assertion `g_utf8_validate (text, len, NULL)' failed
GNOME PPP: STDERR: --> pppd: ï¿½ï¿½[05][08]Xï¿½[05][08]xï¿½[05][08]ï¿½[12][06][08]Pï¿½[05][08]pï¿½[05][08]ï¿½ï¿½[05][08]

(gnome-ppp:6247): Gtk-CRITICAL **: gtk_text_buffer_emit_insert: assertion `g_utf8_validate (text, len, NULL)' failed
GNOME PPP: STDERR: --> pppd: ï¿½ï¿½[05][08]Xï¿½[05][08]xï¿½[05][08]ï¿½[12][06][08]Pï¿½[05][08]pï¿½[05][08]ï¿½ï¿½[05][08]

(gnome-ppp:6247): Gtk-CRITICAL **: gtk_text_buffer_emit_insert: assertion `g_utf8_validate (text, len, NULL)' failed
GNOME PPP: STDERR: --> Disconnecting at Sat Sep  8 10:46:41 2007
GNOME PPP: STDERR: --> The PPP daemon has died: A modem hung up the phone (exit code = 16)
GNOME PPP: STDERR: --> man pppd explains pppd error codes in more detail.
GNOME PPP: STDERR: --> Try again and look into /var/log/messages and the wvdial and pppd man pages for more information.

and here with wvdial:

コード:

~$ sudo wvdial
Password:
--> Ignoring malformed input line: ";Do NOT edit this file by hand!"
--> Ignoring malformed input line: ";Do NOT edit this file by hand!"
--> WvDial: Internet dialer version 1.55
--> Initializing modem.
--> Sending: ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2
ATQ0 V1 E1 S0=0 &C1 &D2
OK
--> Sending: ATW
ATW
OK
--> Modem initialized.
--> Sending: ATDT1492
--> Waiting for carrier.
ATDT1492
CONNECT 64000
--> Carrier detected.  Starting PPP immediately.
--> Starting pppd at Sat Sep  8 10:29:45 2007
--> Pid of pppd: 5310
--> Using interface ppp0
--> pppd: ï¿½ï¿½[05][08]
--> pppd: ï¿½ï¿½[05][08]
--> pppd: ï¿½ï¿½[05][08]
--> pppd: ï¿½ï¿½[05][08]
--> Disconnecting at Sat Sep  8 10:29:49 2007
--> The PPP daemon has died: A modem hung up the phone (exit code = 16)
--> man pppd explains pppd error codes in more detail.
--> Try again and look into /var/log/messages and the wvdial and pppd man pages for more information.

It connects and then hangs up almost immediately (exit code=16).

I also noticed that every time I use gnome-ppp it changes my /root/.wvdial.conf file and inputs some corrupted data (it changes my ATDT setting to AT, it turns the modem password on from off, and it erases my login password). This is not too bothering a problem though and I think I could live with this tiny hassle as long as I could get to the internet with my dapper.

Is there a way to record or to see the exchange going on between my Aterm and the ISP while connecting under Windows ? I think that would be most useful don't you think ?

I here again thank you for the time and effort you are investing in this problem.

O sewa ni narimashita.

Ubuntu日本語フォーラム

お知らせ

#1 2007-08-31 19:18:12

ISDN modem Aterm IT21 L installation help needed

#2 2007-08-31 22:08:01

Re: ISDN modem Aterm IT21 L installation help needed

コード:

#3 2007-08-31 23:21:19

Re: ISDN modem Aterm IT21 L installation help needed

コード:

#4 2007-09-01 23:32:56

Re: ISDN modem Aterm IT21 L installation help needed

#5 2007-09-02 17:24:11

Re: ISDN modem Aterm IT21 L installation help needed

#6 2007-09-02 22:40:44

Re: ISDN modem Aterm IT21 L installation help needed

コード:

#7 2007-09-03 20:24:03

Re: ISDN modem Aterm IT21 L installation help needed

コード:

#8 2007-09-03 23:13:54

Re: ISDN modem Aterm IT21 L installation help needed

コード:

コード:

#9 2007-09-06 02:50:57

Re: ISDN modem Aterm IT21 L installation help needed

コード:

#10 2007-09-07 10:20:52

Re: ISDN modem Aterm IT21 L installation help needed

#11 2007-09-08 18:44:17

Re: ISDN modem Aterm IT21 L installation help needed

コード:

コード:

Board footer