お知らせ

  • 利用規約を守って投稿してください。また、よくある質問および投稿の手引きも参照してください。
  • メッセージの投稿にはアカウントが必要です。未登録の方は、ユーザ登録ページからアカウントを作成することができます。

ページ: 1 2

 

#1 2010-05-13 16:36:05

hiropack
メンバ
登録日: 2009-02-27

10.04LTS ライブCDの立ち上がり時間について

表題の件、私のマシンで電源を入れてから使用できるようになるまで１３分もかかります。　9.10 では3分弱です。
CDがうまく焼けなかったかなと思い数枚焼いてみました。すべてに於いて時間かかってます。

皆さんのマシンでも10.04ではこんなに立ち上がるまで時間かかってるんでしょうか？
インストール後に通常の立ち上がりスピードであればそれでいいんですが、　インストールするのが少し不安になってます。

Opteron クワッド、　2.1 MH,  メモリー２GB　。

オフライン

 

#2 2010-05-13 17:41:11

pc944
メンバ
From: Japan
登録日: 2010-03-03

Re: 10.04LTS ライブCDの立ち上がり時間について

CDはハードディスクにくらべると著しく遅いので普通かと思います。
基本、そのディスクの最高速度とドライブの最高速度によって変わるのと、
メモリが、少ないとそのようになるかもしれません。

オフライン

 

#3 2010-05-13 18:08:22

hmatsue
アドバイザ
登録日: 2009-03-10

Re: 10.04LTS ライブCDの立ち上がり時間について

9.10の起動時間から考えると異常な状態になっているのではないかと思われます。
ちょっと検索してみた感じでは、これというものは見つかりませんでしたが、グラフィックカード/チップなどを元にlauchpadを検索するとなにか見つかるかも知れません。
インストールする前に、しっかりと調査することをお勧めします。

オフライン

 

#4 2010-05-13 18:49:57

hito
管理者
登録日: 2007-03-18

Re: 10.04LTS ライブCDの立ち上がり時間について

pc944 による投稿:

CDはハードディスクにくらべると著しく遅いので普通かと思います。
基本、そのディスクの最高速度とドライブの最高速度によって変わるのと、
メモリが、少ないとそのようになるかもしれません。

読み間違いもあるかなぁ、と思うのですが、
　・13分かかる
　・メモリ2GB
という環境に対するアドバイスとしては、なんだかとてもそぐわないように思います。

オフライン

 

#5 2010-05-13 22:51:31

pc944
メンバ
From: Japan
登録日: 2010-03-03

Re: 10.04LTS ライブCDの立ち上がり時間について

管理者さん＞メモリとCPUの所を見逃していました。きずきませんでした。
ディスクって言うのは、CDとかの16xとかって言われる方です。
100円ショップのCDとかなら、かなり速度が遅かったきがしたので記載しました。
とりあえず、「メモリ少ない」と言う発言は無視してください。私のミスです。

オフライン

 

#6 2010-05-13 23:40:26

gontomo
メンバ
From: 北海道
登録日: 2010-02-17

Re: 10.04LTS ライブCDの立ち上がり時間について

9.10でも、10.04でもそこまでの起動時間の違いはないですね。
ちなみにメディアとドライブの組み合わせにもよりますが、CD-RよりもDVD-Rの方が転送速度という意味での読込速度は速いです。
記録方式の違いによる記録密度の関係でCDは既に頭打ち状態です。
理論上は、DVD x2 = CD x16～x20、 DVD x6 > CD x50

さておきまして。
時間がかかっても起動できるというのであれば、デバイスの認識に時間がかかってるんじゃないかなと思いますがどうでしょ。
起動した後に、/var/log/dmesgを見てみるとどの辺で時間がかかっているか分かるかもしれないですね。

オフライン

 

#7 2010-05-14 11:51:52

hiropack
メンバ
登録日: 2009-02-27

Re: 10.04LTS ライブCDの立ち上がり時間について

やはりこんな時間かかるなんて異常ですよね。。。。いったん立ち上がればストレスなく動作しますが。

追加情報として私のグラフィックカードは　nVidia GeForce7300GT,  PCI x1 タイプです。
Dell のサーバーT１０５で使用してます。

/var/log/dmesg　覗いてみましたが、あまり読み方が分かりません。すみません。結構な量ですが下記に張り付けます。
9.10を含む以前のバージョンではディスクがよく回って情報を読み取っているように感じるのですが、10.04ではディスクの回転も少なく何か小まめに読み取っているような感じです。あくまでディスクのアクセスランプと回転音からの判断ですが。。。

lauchpadの検索は今やっております。今のところ何も見つかってませんが。。。


以下　/var/log/dmesg　の中身です。

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.32-21-generic (buildd@rothera) (gcc version 4.4.3 (Ubuntu 4.4.3-4ubuntu5) ) #32-Ubuntu SMP Fri Apr 16 08:10:02 UTC 2010 (Ubuntu 2.6.32-21.32-generic 2.6.32.11+drm33.2)
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   NSC Geode by NSC
[    0.000000]   Cyrix CyrixInstead
[    0.000000]   Centaur CentaurHauls
[    0.000000]   Transmeta GenuineTMx86
[    0.000000]   Transmeta TransmetaCPU
[    0.000000]   UMC UMC UMC UMC
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
[    0.000000]  BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000007fee0000 (usable)
[    0.000000]  BIOS-e820: 000000007fee0000 - 000000007fee5000 (ACPI data)
[    0.000000]  BIOS-e820: 000000007fee5000 - 000000007ff7f000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved)
[    0.000000]  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[    0.000000] DMI present.
[    0.000000] last_pfn = 0x7fee0 max_arch_pfn = 0x100000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CEFFF write-protect
[    0.000000]   CF000-E3FFF uncachable
[    0.000000]   E4000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000000 mask FFFF80000000 write-back
[    0.000000]   1 disabled
[    0.000000]   2 disabled
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820 update range: 0000000000002000 - 0000000000006000 (usable) ==> (reserved)
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] modified physical RAM map:
[    0.000000]  modified: 0000000000000000 - 0000000000002000 (usable)
[    0.000000]  modified: 0000000000002000 - 0000000000006000 (reserved)
[    0.000000]  modified: 0000000000006000 - 000000000009dc00 (usable)
[    0.000000]  modified: 000000000009dc00 - 00000000000a0000 (reserved)
[    0.000000]  modified: 00000000000ce000 - 0000000000100000 (reserved)
[    0.000000]  modified: 0000000000100000 - 000000007fee0000 (usable)
[    0.000000]  modified: 000000007fee0000 - 000000007fee5000 (ACPI data)
[    0.000000]  modified: 000000007fee5000 - 000000007ff7f000 (ACPI NVS)
[    0.000000]  modified: 000000007ff80000 - 0000000080000000 (reserved)
[    0.000000]  modified: 00000000e0000000 - 00000000f0000000 (reserved)
[    0.000000]  modified: 00000000fec00000 - 00000000fec10000 (reserved)
[    0.000000]  modified: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  modified: 00000000fff80000 - 0000000100000000 (reserved)
[    0.000000] initial memory mapped : 0 - 00c00000
[    0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[    0.000000] Using x86 segment limits to approximate NX protection
[    0.000000]  0000000000 - 0000400000 page 4k
[    0.000000]  0000400000 - 0037400000 page 2M
[    0.000000]  0037400000 - 00377fe000 page 4k
[    0.000000] kernel direct mapping tables up to 377fe000 @ 7000-c000
[    0.000000] RAMDISK: 7f5c1000 - 7feaf970
[    0.000000] Allocated new RAMDISK: 008de000 - 011cc970
[    0.000000] Move RAMDISK from 000000007f5c1000 - 000000007feaf96f to 008de000 - 011cc96f
[    0.000000] ACPI: RSDP 000f79b0 00024 (v02 PTLTD )
[    0.000000] ACPI: XSDT 7fee077b 0009C (v01 DELL   PE_SC3   06040000 DELL 00000000)
[    0.000000] ACPI: FACP 7fee3c87 000F4 (v03 DELL   PE_SC3   06040000 DELL 000F4240)
[    0.000000] ACPI: DSDT 7fee0817 033FC (v01 DELL   PE_SC3   06040000 MSFT 0100000E)
[    0.000000] ACPI: FACS 7fee5fc0 00040
[    0.000000] ACPI: TCPA 7fee3d7b 00032 (v01 Phoeni  x       06040000  TL  00000000)
[    0.000000] ACPI: SLIC 7fee3dad 00024 (v01 DELL   PE_SC3   06040000 PTL  00000001)
[    0.000000] ACPI: SPCR 7fee3dd1 00050 (v01 DELL   PE_SC3   06040000 PTL  00000001)
[    0.000000] ACPI: EINJ 7fee3e21 001B0 (v01 PTL    WHEAPTL  06040000 PTL  00000001)
[    0.000000] ACPI: HEST 7fee3fd1 000A8 (v01 PTL    WHEAPTL  06040000 PTL  00000001)
[    0.000000] ACPI: BERT 7fee4079 00030 (v01 PTL    WHEAPTL  06040000 PTL  00000001)
[    0.000000] ACPI: SSDT 7fee40a9 000E1 (v01 wheaos  wheaosc 06040000 INTL 20050624)
[    0.000000] ACPI: ERST 7fee418a 00270 (v01 PTL    WHEAPTL  06040000 PTL  00000001)
[    0.000000] ACPI: SRAT 7fee43fa 000C0 (v01 AMD    HAMMER   06040000 AMD  00000001)
[    0.000000] ACPI: SSDT 7fee44ba 00A30 (v01 AMD    POWERNOW 06040000 AMD  00000001)
[    0.000000] ACPI: MCFG 7fee4eea 0003C (v01 PTLTD    MCFG   06040000  LTP 00000000)
[    0.000000] ACPI: HPET 7fee4f26 00038 (v01 PTLTD  HPETTBL  06040000  LTP 00000001)
[    0.000000] ACPI: APIC 7fee4f5e 0007A (v01 PTLTD  ? APIC   06040000  LTP 00000000)
[    0.000000] ACPI: BOOT 7fee4fd8 00028 (v01 PTLTD  $SBFTBL$ 06040000  LTP 00000001)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 1158MB HIGHMEM available.
[    0.000000] 887MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 377fe000
[    0.000000]   low ram: 0 - 377fe000
[    0.000000]   node 0 low ram: 00000000 - 377fe000
[    0.000000]   node 0 bootmap 00008000 - 0000ef00
[    0.000000] (9 early reservations) ==> bootmem [0000000000 - 00377fe000]
[    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
[    0.000000]   #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
[    0.000000]   #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
[    0.000000]   #3 [0000100000 - 00008d9e98]    TEXT DATA BSS ==> [0000100000 - 00008d9e98]
[    0.000000]   #4 [000009dc00 - 0000100000]    BIOS reserved ==> [000009dc00 - 0000100000]
[    0.000000]   #5 [00008da000 - 00008dd0e4]              BRK ==> [00008da000 - 00008dd0e4]
[    0.000000]   #6 [0000007000 - 0000008000]          PGTABLE ==> [0000007000 - 0000008000]
[    0.000000]   #7 [00008de000 - 00011cc970]      NEW RAMDISK ==> [00008de000 - 00011cc970]
[    0.000000]   #8 [0000008000 - 000000f000]          BOOTMAP ==> [0000008000 - 000000f000]
[    0.000000] found SMP MP-table at [c00f7a70] f7a70
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000000 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x000377fe
[    0.000000]   HighMem  0x000377fe -> 0x0007fee0
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[3] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00000002
[    0.000000]     0: 0x00000006 -> 0x0000009d
[    0.000000]     0: 0x00000100 -> 0x0007fee0
[    0.000000] On node 0 totalpages: 523897
[    0.000000] free_area_init_node: node 0, pgdat c0798720, node_mem_map c11ce000
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3961 pages, LIFO batch:0
[    0.000000]   Normal zone: 1744 pages used for memmap
[    0.000000]   Normal zone: 221486 pages, LIFO batch:31
[    0.000000]   HighMem zone: 2318 pages used for memmap
[    0.000000]   HighMem zone: 294356 pages, LIFO batch:31
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x8008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
[    0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 24
[    0.000000] PM: Registered nosave memory: 0000000000002000 - 0000000000006000
[    0.000000] PM: Registered nosave memory: 000000000009d000 - 000000000009e000
[    0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000ce000
[    0.000000] PM: Registered nosave memory: 00000000000ce000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:60000000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 14 pages/cpu @c2400000 s36024 r0 d21320 u1048576
[    0.000000] pcpu-alloc: s36024 r0 d21320 u1048576 alloc=1*4194304
[    0.000000] pcpu-alloc: [0] 0 1 2 3
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 519803
[    0.000000] Kernel command line: BOOT_IMAGE=/casper/vmlinuz file=/cdrom/preseed/ubuntu.seed boot=casper initrd=/casper/initrd.lz quiet splash -- debian-installer/language=ja console-setup/layoutcode?=jp console-setup/modelcode?=jp106 maybe-ubiquity
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] allocated 10480000 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Initializing HighMem for node 0 (000377fe:0007fee0)
[    0.000000] Memory: 2049616k/2096000k available (4673k kernel code, 44916k reserved, 2122k data, 656k init, 1186696k highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xfff1d000 - 0xfffff000   ( 904 kB)
[    0.000000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.000000]     vmalloc : 0xf7ffe000 - 0xff7fe000   ( 120 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf77fe000   ( 887 MB)
[    0.000000]       .init : 0xc07a3000 - 0xc0847000   ( 656 kB)
[    0.000000]       .data : 0xc0590613 - 0xc07a2e48   (2122 kB)
[    0.000000]       .text : 0xc0100000 - 0xc0590613   (4673 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:2304 nr_irqs:440
[    0.000000] Extended CMOS year: 2000
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] hpet clockevent registered
[    0.000000] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 2109.364 MHz processor.
[    0.004005] Calibrating delay loop (skipped), value calculated using timer frequency.. 4218.72 BogoMIPS (lpj=8437456)
[    0.004021] Security Framework initialized
[    0.004039] AppArmor: AppArmor initialized
[    0.004046] Mount-cache hash table entries: 512
[    0.004151] Initializing cgroup subsys ns
[    0.004154] Initializing cgroup subsys cpuacct
[    0.004158] Initializing cgroup subsys memory
[    0.004164] Initializing cgroup subsys devices
[    0.004167] Initializing cgroup subsys freezer
[    0.004169] Initializing cgroup subsys net_cls
[    0.004184] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[    0.004187] CPU: L2 Cache: 512K (64 bytes/line)
[    0.004190] CPU: Physical Processor ID: 0
[    0.004191] CPU: Processor Core ID: 0
[    0.004195] mce: CPU supports 6 MCE banks
[    0.004204] using C1E aware idle routine
[    0.004209] Performance Events: AMD PMU driver.
[    0.004215] ... version:                0
[    0.004217] ... bit width:              48
[    0.004219] ... generic registers:      4
[    0.004221] ... value mask:             0000ffffffffffff
[    0.004223] ... max period:             00007fffffffffff
[    0.004225] ... fixed-purpose events:   0
[    0.004227] ... event mask:             000000000000000f
[    0.004231] Checking 'hlt' instruction... OK.
[    0.022158] ACPI: Core revision 20090903
[    0.028008] ftrace: converting mcount calls to 0f 1f 44 00 00
[    0.028013] ftrace: allocating 21771 entries in 43 pages
[    0.032060] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.032341] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.074824] CPU0: Quad-Core AMD Opteron(tm) Processor 1352 stepping 03
[    0.076001] Booting processor 1 APIC 0x1 ip 0x6000
[    0.008000] Initializing CPU#1
[    0.008000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[    0.008000] CPU: L2 Cache: 512K (64 bytes/line)
[    0.008000] CPU: Physical Processor ID: 0
[    0.008000] CPU: Processor Core ID: 1
[    0.160031] CPU1: Quad-Core AMD Opteron(tm) Processor 1352 stepping 03
[    0.160042] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[    0.164067] Booting processor 2 APIC 0x2 ip 0x6000
[    0.008000] Initializing CPU#2
[    0.008000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[    0.008000] CPU: L2 Cache: 512K (64 bytes/line)
[    0.008000] CPU: Physical Processor ID: 0
[    0.008000] CPU: Processor Core ID: 2
[    0.252091] CPU2: Quad-Core AMD Opteron(tm) Processor 1352 stepping 03
[    0.252102] checking TSC synchronization [CPU#0 -> CPU#2]: passed.
[    0.256065] Booting processor 3 APIC 0x3 ip 0x6000
[    0.008000] Initializing CPU#3
[    0.008000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[    0.008000] CPU: L2 Cache: 512K (64 bytes/line)
[    0.008000] CPU: Physical Processor ID: 0
[    0.008000] CPU: Processor Core ID: 3
[    0.344049] CPU3: Quad-Core AMD Opteron(tm) Processor 1352 stepping 03
[    0.344061] checking TSC synchronization [CPU#0 -> CPU#3]: passed.
[    0.348012] Brought up 4 CPUs
[    0.348014] Total of 4 processors activated (16877.39 BogoMIPS).
[    0.349030] CPU0 attaching sched-domain:
[    0.349033]  domain 0: span 0-3 level MC
[    0.349036]   groups: 0 1 2 3
[    0.349042] CPU1 attaching sched-domain:
[    0.349044]  domain 0: span 0-3 level MC
[    0.349047]   groups: 1 2 3 0
[    0.349052] CPU2 attaching sched-domain:
[    0.349054]  domain 0: span 0-3 level MC
[    0.349056]   groups: 2 3 0 1
[    0.349061] CPU3 attaching sched-domain:
[    0.349063]  domain 0: span 0-3 level MC
[    0.349065]   groups: 3 0 1 2
[    0.349168] devtmpfs: initialized
[    0.349168] regulator: core version 0.5
[    0.349168] Time: 11:19:49  Date: 05/14/10
[    0.349168] NET: Registered protocol family 16
[    0.349168] Trying to unpack rootfs image as initramfs...
[    0.349168] EISA bus registered
[    0.349168] ACPI: bus type pci registered
[    0.349168] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 4
[    0.349168] PCI: MCFG area at e0000000 reserved in E820
[    0.349168] PCI: Using MMCONFIG for extended config space
[    0.349168] PCI: Using configuration type 1 for base access
[    0.349168] bio: create slab <bio-0> at 0
[    0.349168] ACPI: EC: Look up EC in DSDT
[    0.352461] ACPI Warning for \_SB_._OSC: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
[    0.352470] \_SB_:_OSC evaluation returned wrong type
[    0.352471] _OSC request data:1 7
[    0.354545] ACPI: Interpreter enabled
[    0.354550] ACPI: (supports S0 S4 S5)
[    0.354565] ACPI: Using IOAPIC for interrupt routing
[    0.358604] ACPI: No dock devices found.
[    0.358698] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.358783] pci 0000:00:01.0: reg 10 io port: [0x8c00-0x8fff]
[    0.358808] pci 0000:00:01.1: reg 10 io port: [0x2080-0x209f]
[    0.358816] pci 0000:00:01.1: reg 20 io port: [0x2040-0x207f]
[    0.358820] pci 0000:00:01.1: reg 24 io port: [0x2000-0x203f]
[    0.358831] pci 0000:00:01.1: PME# supported from D3hot D3cold
[    0.358834] pci 0000:00:01.1: PME# disabled
[    0.358852] pci 0000:00:02.0: reg 10 32bit mmio: [0xc0000000-0xc0000fff]
[    0.358870] pci 0000:00:02.0: supports D1 D2
[    0.358872] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.358875] pci 0000:00:02.0: PME# disabled
[    0.358893] pci 0000:00:02.1: reg 10 32bit mmio: [0xc0001000-0xc00010ff]
[    0.358913] pci 0000:00:02.1: supports D1 D2
[    0.358915] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.358919] pci 0000:00:02.1: PME# disabled
[    0.358944] pci 0000:00:07.0: reg 10 io port: [0x20f0-0x20f7]
[    0.358948] pci 0000:00:07.0: reg 14 io port: [0x20e0-0x20e3]
[    0.358952] pci 0000:00:07.0: reg 18 io port: [0x20d0-0x20d7]
[    0.358956] pci 0000:00:07.0: reg 1c io port: [0x20c0-0x20c3]
[    0.358960] pci 0000:00:07.0: reg 20 io port: [0x20b0-0x20bf]
[    0.358964] pci 0000:00:07.0: reg 24 32bit mmio: [0xc0002000-0xc0002fff]
[    0.358994] pci 0000:00:08.0: reg 10 io port: [0x2440-0x2447]
[    0.358998] pci 0000:00:08.0: reg 14 io port: [0x2430-0x2433]
[    0.359002] pci 0000:00:08.0: reg 18 io port: [0x2420-0x2427]
[    0.359006] pci 0000:00:08.0: reg 1c io port: [0x2410-0x2413]
[    0.359010] pci 0000:00:08.0: reg 20 io port: [0x2400-0x240f]
[    0.359014] pci 0000:00:08.0: reg 24 32bit mmio: [0xc0003000-0xc0003fff]
[    0.359066] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.359069] pci 0000:00:0b.0: PME# disabled
[    0.359101] pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.359104] pci 0000:00:0c.0: PME# disabled
[    0.359134] pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.359137] pci 0000:00:0d.0: PME# disabled
[    0.359167] pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.359170] pci 0000:00:0e.0: PME# disabled
[    0.359282] pci 0000:01:08.0: reg 10 32bit mmio pref: [0xc8000000-0xcfffffff]
[    0.359288] pci 0000:01:08.0: reg 14 io port: [0x3000-0x30ff]
[    0.359293] pci 0000:01:08.0: reg 18 32bit mmio: [0xc0100000-0xc010ffff]
[    0.359307] pci 0000:01:08.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
[    0.359319] pci 0000:01:08.0: supports D1 D2
[    0.359342] pci 0000:00:09.0: bridge io port: [0x3000-0x3fff]
[    0.359345] pci 0000:00:09.0: bridge 32bit mmio: [0xc0100000-0xc01fffff]
[    0.359349] pci 0000:00:09.0: bridge 32bit mmio pref: [0xc8000000-0xcfffffff]
[    0.359391] pci 0000:02:00.0: reg 10 64bit mmio: [0xc0200000-0xc020ffff]
[    0.359440] pci 0000:02:00.0: PME# supported from D3hot D3cold
[    0.359444] pci 0000:02:00.0: PME# disabled
[    0.359481] pci 0000:00:0b.0: bridge 32bit mmio: [0xc0200000-0xc02fffff]
[    0.359507] pci 0000:03:00.0: reg 10 32bit mmio: [0xc2000000-0xc2ffffff]
[    0.359516] pci 0000:03:00.0: reg 14 64bit mmio pref: [0xd0000000-0xdfffffff]
[    0.359524] pci 0000:03:00.0: reg 1c 64bit mmio: [0xc1000000-0xc1ffffff]
[    0.359530] pci 0000:03:00.0: reg 24 io port: [0x4000-0x407f]
[    0.359535] pci 0000:03:00.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
[    0.359584] pci 0000:00:0c.0: bridge io port: [0x4000-0x4fff]
[    0.359586] pci 0000:00:0c.0: bridge 32bit mmio: [0xc1000000-0xc2ffffff]
[    0.359590] pci 0000:00:0c.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
[    0.359653] pci_bus 0000:00: on NUMA node 0
[    0.359657] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.359719] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
[    0.359754] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT]
[    0.359779] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
[    0.359802] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR2._PRT]
[    0.359823] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR3._PRT]
[    0.375701] ACPI: PCI Interrupt Link [LNK1] (IRQs 16 17 18 19) *0
[    0.375844] ACPI: PCI Interrupt Link [LNK2] (IRQs 16 17 18 19) *0
[    0.375982] ACPI: PCI Interrupt Link [LNK3] (IRQs 16 17 18 19) *0, disabled.
[    0.376128] ACPI: PCI Interrupt Link [LNK4] (IRQs 16 17 18 19) *0, disabled.
[    0.376265] ACPI: PCI Interrupt Link [LNK5] (IRQs 16 17 18 19) *0, disabled.
[    0.376403] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *0
[    0.376539] ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22 23) *0
[    0.376676] ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22 23) *0, disabled.
[    0.376813] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled.
[    0.376950] ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0, disabled.
[    0.377089] ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22 23) *0, disabled.
[    0.377229] ACPI: PCI Interrupt Link [LPID] (IRQs 20 21 22 23) *0, disabled.
[    0.377373] ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22 23) *0
[    0.377516] ACPI: PCI Interrupt Link [LSI1] (IRQs 20 21 22 23) *0
[    0.377659] ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
[    0.377750] vgaarb: device added: PCI:0000:01:08.0,decodes=io+mem,owns=none,locks=none
[    0.377756] vgaarb: device added: PCI:0000:03:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.377759] vgaarb: loaded
[    0.377851] SCSI subsystem initialized
[    0.377875] libata version 3.00 loaded.
[    0.377875] usbcore: registered new interface driver usbfs
[    0.377875] usbcore: registered new interface driver hub
[    0.377875] usbcore: registered new device driver usb
[    0.377875] ACPI: WMI: Mapper loaded
[    0.377875] PCI: Using ACPI for IRQ routing
[    0.377875] NetLabel: Initializing
[    0.377875] NetLabel:  domain hash size = 128
[    0.377875] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.377875] NetLabel:  unlabeled traffic allowed by default
[    0.377875] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[    0.377875] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
[    2.284022] Switching to clocksource tsc
[    2.285658] AppArmor: AppArmor Filesystem Enabled
[    2.285672] pnp: PnP ACPI init
[    2.285687] ACPI: bus type pnp registered
[    2.287919] pnp: PnP ACPI: found 12 devices
[    2.287922] ACPI: ACPI bus type pnp unregistered
[    2.287925] PnPBIOS: Disabled by ACPI PNP
[    2.287938] system 00:00: iomem range 0xffc00000-0xffffffff could not be reserved
[    2.287942] system 00:00: iomem range 0xfec00000-0xfec00fff could not be reserved
[    2.287946] system 00:00: iomem range 0xfee00000-0xfeefffff could not be reserved
[    2.287949] system 00:00: iomem range 0xfed00000-0xfed00fff has been reserved
[    2.287955] system 00:02: iomem range 0xe0000000-0xefffffff has been reserved
[    2.287961] system 00:03: ioport range 0x8000-0x807f has been reserved
[    2.287964] system 00:03: ioport range 0x8080-0x80ff has been reserved
[    2.287967] system 00:03: ioport range 0x8400-0x847f has been reserved
[    2.287970] system 00:03: ioport range 0x8480-0x84ff has been reserved
[    2.287973] system 00:03: ioport range 0x8800-0x887f has been reserved
[    2.287976] system 00:03: ioport range 0x8880-0x88ff has been reserved
[    2.287979] system 00:03: ioport range 0x2040-0x207f has been reserved
[    2.287982] system 00:03: ioport range 0x2000-0x203f has been reserved
[    2.287988] system 00:05: ioport range 0x4d0-0x4d1 has been reserved
[    2.287994] system 00:0a: ioport range 0xc00-0xc7f has been reserved
[    2.313089] Freeing initrd memory: 9146k freed
[    2.322696] pci 0000:00:09.0: PCI bridge, secondary bus 0000:01
[    2.322699] pci 0000:00:09.0:   IO window: 0x3000-0x3fff
[    2.322703] pci 0000:00:09.0:   MEM window: 0xc0100000-0xc01fffff
[    2.322706] pci 0000:00:09.0:   PREFETCH window: 0xc8000000-0xcfffffff
[    2.322710] pci 0000:00:0b.0: PCI bridge, secondary bus 0000:02
[    2.322712] pci 0000:00:0b.0:   IO window: disabled
[    2.322715] pci 0000:00:0b.0:   MEM window: 0xc0200000-0xc02fffff
[    2.322718] pci 0000:00:0b.0:   PREFETCH window: disabled
[    2.322724] pci 0000:03:00.0: BAR 6: can't allocate mem resource [0xe0000000-0xdfffffff]
[    2.322727] pci 0000:00:0c.0: PCI bridge, secondary bus 0000:03
[    2.322729] pci 0000:00:0c.0:   IO window: 0x4000-0x4fff
[    2.322733] pci 0000:00:0c.0:   MEM window: 0xc1000000-0xc2ffffff
[    2.322736] pci 0000:00:0c.0:   PREFETCH window: 0x000000d0000000-0x000000dfffffff
[    2.322740] pci 0000:00:0d.0: PCI bridge, secondary bus 0000:04
[    2.322742] pci 0000:00:0d.0:   IO window: disabled
[    2.322744] pci 0000:00:0d.0:   MEM window: disabled
[    2.322747] pci 0000:00:0d.0:   PREFETCH window: disabled
[    2.322750] pci 0000:00:0e.0: PCI bridge, secondary bus 0000:05
[    2.322752] pci 0000:00:0e.0:   IO window: disabled
[    2.322755] pci 0000:00:0e.0:   MEM window: disabled
[    2.322758] pci 0000:00:0e.0:   PREFETCH window: disabled
[    2.322767] pci 0000:00:09.0: setting latency timer to 64
[    2.322772] pci 0000:00:0b.0: setting latency timer to 64
[    2.322777] pci 0000:00:0c.0: setting latency timer to 64
[    2.322782] pci 0000:00:0d.0: setting latency timer to 64
[    2.322786] pci 0000:00:0e.0: setting latency timer to 64
[    2.322790] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
[    2.322793] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[    2.322796] pci_bus 0000:01: resource 0 io:  [0x3000-0x3fff]
[    2.322798] pci_bus 0000:01: resource 1 mem: [0xc0100000-0xc01fffff]
[    2.322801] pci_bus 0000:01: resource 2 pref mem [0xc8000000-0xcfffffff]
[    2.322804] pci_bus 0000:02: resource 1 mem: [0xc0200000-0xc02fffff]
[    2.322807] pci_bus 0000:03: resource 0 io:  [0x4000-0x4fff]
[    2.322810] pci_bus 0000:03: resource 1 mem: [0xc1000000-0xc2ffffff]
[    2.322813] pci_bus 0000:03: resource 2 pref mem [0xd0000000-0xdfffffff]
[    2.322851] NET: Registered protocol family 2
[    2.322961] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    2.323318] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    2.323882] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    2.324174] TCP: Hash tables configured (established 131072 bind 65536)
[    2.324176] TCP reno registered
[    2.324264] NET: Registered protocol family 1
[    2.324342] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324369] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324401] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324407] pci 0000:00:0b.0: Found disabled HT MSI Mapping
[    2.324414] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324419] pci 0000:00:0b.0: Linking AER extended capability
[    2.324454] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324459] pci 0000:00:0c.0: Found disabled HT MSI Mapping
[    2.324467] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324470] pci 0000:00:0c.0: Linking AER extended capability
[    2.324508] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324514] pci 0000:00:0d.0: Found disabled HT MSI Mapping
[    2.324521] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324524] pci 0000:00:0d.0: Linking AER extended capability
[    2.324565] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324570] pci 0000:00:0e.0: Found disabled HT MSI Mapping
[    2.324577] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324580] pci 0000:00:0e.0: Linking AER extended capability
[    2.324599] pci 0000:03:00.0: Boot video device
[    2.324622] Simple Boot Flag at 0x62 set to 0x1
[    2.324985] cpufreq-nforce2: No nForce2 chipset.
[    2.325009] Scanning for low memory corruption every 60 seconds
[    2.325119] audit: initializing netlink socket (disabled)
[    2.325128] type=2000 audit(1273835990.324:1): initialized
[    2.333676] highmem bounce pool size: 64 pages
[    2.333683] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    2.335456] VFS: Disk quotas dquot_6.5.2
[    2.335518] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    2.336126] fuse init (API version 7.13)
[    2.336214] msgmni has been set to 1705
[    2.336477] alg: No test for stdrng (krng)
[    2.336529] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    2.336533] io scheduler noop registered
[    2.336535] io scheduler anticipatory registered
[    2.336537] io scheduler deadline registered
[    2.336582] io scheduler cfq registered (default)
[    2.336693]   alloc irq_desc for 24 on node -1
[    2.336696]   alloc kstat_irqs on node -1
[    2.336704] pcieport 0000:00:0b.0: irq 24 for MSI/MSI-X
[    2.336709] pcieport 0000:00:0b.0: setting latency timer to 64
[    2.336780]   alloc irq_desc for 25 on node -1
[    2.336782]   alloc kstat_irqs on node -1
[    2.336786] pcieport 0000:00:0c.0: irq 25 for MSI/MSI-X
[    2.336790] pcieport 0000:00:0c.0: setting latency timer to 64
[    2.336857]   alloc irq_desc for 26 on node -1
[    2.336858]   alloc kstat_irqs on node -1
[    2.336863] pcieport 0000:00:0d.0: irq 26 for MSI/MSI-X
[    2.336867] pcieport 0000:00:0d.0: setting latency timer to 64
[    2.336932]   alloc irq_desc for 27 on node -1
[    2.336933]   alloc kstat_irqs on node -1
[    2.336938] pcieport 0000:00:0e.0: irq 27 for MSI/MSI-X
[    2.336942] pcieport 0000:00:0e.0: setting latency timer to 64
[    2.337003] aer 0000:00:0b.0:pcie02: AER service couldn't init device: no _OSC support
[    2.337010] aer 0000:00:0c.0:pcie02: AER service couldn't init device: no _OSC support
[    2.337016] aer 0000:00:0d.0:pcie02: AER service couldn't init device: no _OSC support
[    2.337022] aer 0000:00:0e.0:pcie02: AER service couldn't init device: no _OSC support
[    2.337039] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    2.337064] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    2.337151] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[    2.337155] ACPI: Power Button [PWRB]
[    2.337204] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    2.337212] ACPI: Power Button [PWRF]
[    2.337606] processor LNXCPU:00: registered as cooling_device0
[    2.337637] processor LNXCPU:01: registered as cooling_device1
[    2.337670] processor LNXCPU:02: registered as cooling_device2
[    2.337697] processor LNXCPU:03: registered as cooling_device3
[    2.339633] isapnp: Scanning for PnP cards...
[    2.340815] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    2.340902] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    2.341205] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    2.342190] brd: module loaded
[    2.342636] loop: module loaded
[    2.342711] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[    2.343113] ACPI: PCI Interrupt Link [LTID] enabled at IRQ 23
[    2.343118]   alloc irq_desc for 23 on node -1
[    2.343120]   alloc kstat_irqs on node -1
[    2.343126] pata_acpi 0000:00:07.0: PCI INT A -> Link[LTID] -> GSI 23 (level, low) -> IRQ 23
[    2.343154] pata_acpi 0000:00:07.0: setting latency timer to 64
[    2.343164] pata_acpi 0000:00:07.0: PCI INT A disabled
[    2.343430] ACPI: PCI Interrupt Link [LSI1] enabled at IRQ 22
[    2.343433]   alloc irq_desc for 22 on node -1
[    2.343435]   alloc kstat_irqs on node -1
[    2.343439] pata_acpi 0000:00:08.0: PCI INT A -> Link[LSI1] -> GSI 22 (level, low) -> IRQ 22
[    2.343457] pata_acpi 0000:00:08.0: setting latency timer to 64
[    2.343463] pata_acpi 0000:00:08.0: PCI INT A disabled
[    2.343742] Fixed MDIO Bus: probed
[    2.343774] PPP generic driver version 2.4.2
[    2.343802] tun: Universal TUN/TAP device driver, 1.6
[    2.343804] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    2.343883] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.344115] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 21
[    2.344118]   alloc irq_desc for 21 on node -1
[    2.344120]   alloc kstat_irqs on node -1
[    2.344124] ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUS2] -> GSI 21 (level, low) -> IRQ 21
[    2.344134] ehci_hcd 0000:00:02.1: setting latency timer to 64
[    2.344137] ehci_hcd 0000:00:02.1: EHCI Host Controller
[    2.344165] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
[    2.344184] ehci_hcd 0000:00:02.1: debug port 1
[    2.344189] ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
[    2.344203] ehci_hcd 0000:00:02.1: irq 21, io mem 0xc0001000
[    2.356019] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
[    2.356091] usb usb1: configuration #1 chosen from 1 choice
[    2.356116] hub 1-0:1.0: USB hub found
[    2.356126] hub 1-0:1.0: 9 ports detected
[    2.356184] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.356403] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 20
[    2.356406]   alloc irq_desc for 20 on node -1
[    2.356408]   alloc kstat_irqs on node -1
[    2.356412] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 20 (level, low) -> IRQ 20
[    2.356420] ohci_hcd 0000:00:02.0: setting latency timer to 64
[    2.356423] ohci_hcd 0000:00:02.0: OHCI Host Controller
[    2.356448] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[    2.356464] ohci_hcd 0000:00:02.0: irq 20, io mem 0xc0000000
[    2.414071] usb usb2: configuration #1 chosen from 1 choice
[    2.414101] hub 2-0:1.0: USB hub found
[    2.414108] hub 2-0:1.0: 9 ports detected
[    2.414150] uhci_hcd: USB Universal Host Controller Interface driver
[    2.414217] PNP: No PS/2 controller found. Probing ports directly.
[    2.416985] serio: i8042 KBD port at 0x60,0x64 irq 1
[    2.416991] serio: i8042 AUX port at 0x60,0x64 irq 12
[    2.417061] mice: PS/2 mouse device common for all mice
[    2.417156] rtc_cmos 00:08: RTC can wake from S4
[    2.417186] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
[    2.417208] rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[    2.417306] device-mapper: uevent: version 1.0.3
[    2.417394] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    2.417503] device-mapper: multipath: version 1.1.0 loaded
[    2.417506] device-mapper: multipath round-robin: version 1.0.0 loaded
[    2.417617] EISA: Probing bus 0 at eisa.0
[    2.417625] Cannot allocate resource for EISA slot 2
[    2.417628] Cannot allocate resource for EISA slot 3
[    2.417630] Cannot allocate resource for EISA slot 4
[    2.417638] Cannot allocate resource for EISA slot 8
[    2.417640] EISA: Detected 0 cards.
[    2.417821] cpuidle: using governor ladder
[    2.417854] cpuidle: using governor menu
[    2.418316] TCP cubic registered
[    2.418476] NET: Registered protocol family 10
[    2.418977] lo: Disabled Privacy Extensions
[    2.419322] NET: Registered protocol family 17
[    2.419354] powernow-k8: Found 1 Quad-Core AMD Opteron(tm) Processor 1352 processors (4 cpu cores) (version 2.20.00)
[    2.419395] powernow-k8:    0 : pstate 0 (2100 MHz)
[    2.419398] powernow-k8:    1 : pstate 1 (1800 MHz)
[    2.419400] powernow-k8:    2 : pstate 2 (1600 MHz)
[    2.419402] powernow-k8:    3 : pstate 3 (1300 MHz)
[    2.419404] powernow-k8:    4 : pstate 4 (1050 MHz)
[    2.432303] Using IPI No-Shortcut mode
[    2.432387] PM: Resume from disk failed.
[    2.432398] registered taskstats version 1
[    2.432636]   Magic number: 10:481:327
[    2.432700] rtc_cmos 00:08: setting system clock to 2010-05-14 11:19:51 UTC (1273835991)
[    2.432704] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    2.432705] EDD information not available.
[    2.693430] isapnp: No Plug & Play device found
[    2.693453] Freeing unused kernel memory: 656k freed
[    2.693793] Write protecting the kernel text: 4676k
[    2.693834] Write protecting the kernel read-only data: 1840k
[    2.712610] udev: starting version 151
[    2.740654] sata_nv 0000:00:07.0: version 3.5
[    2.740668] sata_nv 0000:00:07.0: PCI INT A -> Link[LTID] -> GSI 23 (level, low) -> IRQ 23
[    2.740708] sata_nv 0000:00:07.0: setting latency timer to 64
[    2.741872] scsi0 : sata_nv
[    2.741989] scsi1 : sata_nv
[    2.742135] ata1: SATA max UDMA/133 cmd 0x20f0 ctl 0x20e0 bmdma 0x20b0 irq 23
[    2.742138] ata2: SATA max UDMA/133 cmd 0x20d0 ctl 0x20c0 bmdma 0x20b8 irq 23
[    2.742177] sata_nv 0000:00:08.0: PCI INT A -> Link[LSI1] -> GSI 22 (level, low) -> IRQ 22
[    2.742208] sata_nv 0000:00:08.0: setting latency timer to 64
[    2.742574] scsi2 : sata_nv
[    2.743537] scsi3 : sata_nv
[    2.743654] ata3: SATA max UDMA/133 cmd 0x2440 ctl 0x2430 bmdma 0x2400 irq 22
[    2.743657] ata4: SATA max UDMA/133 cmd 0x2420 ctl 0x2410 bmdma 0x2408 irq 22
[    2.755717] Linux agpgart interface v0.103
[    2.758984] tg3.c:v3.102 (September 1, 2009)
[    2.759244] ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 19
[    2.759253]   alloc irq_desc for 19 on node -1
[    2.759256]   alloc kstat_irqs on node -1
[    2.759263] tg3 0000:02:00.0: PCI INT A -> Link[LNK2] -> GSI 19 (level, low) -> IRQ 19
[    2.759271] tg3 0000:02:00.0: setting latency timer to 64
[    2.777225] eth0: Tigon3 [partno(BCM95722) rev a200] (PCI Express) MAC address 00:22:19:1b:bc:17
[    2.777229] eth0: attached PHY is 5722/5756 (10/100/1000Base-T Ethernet) (WireSpeed[1])
[    2.777232] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    2.777235] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[    2.780396] [drm] Initialized drm 1.1.0 20060810
[    2.797034] usb 1-5: new high speed USB device using ehci_hcd and address 3
[    2.931656] usb 1-5: configuration #1 chosen from 1 choice
[    2.939665] Initializing USB Mass Storage driver...
[    2.939763] scsi4 : SCSI emulation for USB Mass Storage devices
[    2.939837] usb-storage: device found at 3
[    2.939839] usb-storage: waiting for device to settle before scanning
[    2.939848] usbcore: registered new interface driver usb-storage
[    2.939851] USB Mass Storage support registered.
[    3.208027] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    3.208170] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    3.216249] ata3.00: ATAPI: TSSTcorp DVD+/-RW TS-H653G, DW10, max UDMA/100
[    3.216263] ata3.00: applying bridge limits
[    3.216449] ata1.00: ATA-7: SAMSUNG HE160HJ, JF800-24, max UDMA7
[    3.216453] ata1.00: 312500000 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    3.224240] ata1.00: configured for UDMA/133
[    3.224337] scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HE160HJ  JF80 PQ: 0 ANSI: 5
[    3.224485] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    3.224510] sd 0:0:0:0: [sda] 312500000 512-byte logical blocks: (160 GB/149 GiB)
[    3.224571] sd 0:0:0:0: [sda] Write Protect is off
[    3.224574] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    3.224596] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.224726]  sda: sda1 sda2 <
[    3.233886] ata3.00: configured for UDMA/100
[    3.260051]  sda5 > sda3
[    3.260309] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.292021] usb 2-2: new full speed USB device using ohci_hcd and address 2
[    3.501286] usb 2-2: configuration #1 chosen from 1 choice
[    3.536031] ata2: SATA link down (SStatus 0 SControl 300)
[    3.537153] scsi 2:0:0:0: CD-ROM            TSSTcorp DVD+-RW TS-H653G DW10 PQ: 0 ANSI: 5
[    3.539366] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[    3.539369] Uniform CD-ROM driver Revision: 3.20
[    3.539467] sr 2:0:0:0: Attached scsi CD-ROM sr0
[    3.539517] sr 2:0:0:0: Attached scsi generic sg1 type 5
[    3.808023] usb 2-7: new low speed USB device using ohci_hcd and address 3
[    3.848024] ata4: SATA link down (SStatus 0 SControl 300)
[    3.853418] usbcore: registered new interface driver hiddev
[    3.861356] input: C-Media USB Headphone Set   as /devices/pci0000:00/0000:00:02.0/usb2/2-2/2-2:1.3/input/input3
[    3.861438] generic-usb 0003:0D8C:000C.0001: input,hidraw0: USB HID v1.00 Device [C-Media USB Headphone Set  ] on usb-0000:00:02.0-2/input3
[    3.861467] usbcore: registered new interface driver usbhid
[    3.861470] usbhid: v2.6:USB HID core driver
[    3.895402] [drm] radeon disabling kernel modesetting for known bad device.
[    3.895536] pci 0000:01:08.0: enabling device (0384 -> 0387)
[    3.895818] ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 18
[    3.895824]   alloc irq_desc for 18 on node -1
[    3.895827]   alloc kstat_irqs on node -1
[    3.895835] pci 0000:01:08.0: PCI INT A -> Link[LNK1] -> GSI 18 (level, low) -> IRQ 18
[    3.895981] [drm] Initialized radeon 1.32.0 20080528 for 0000:01:08.0 on minor 0
[    3.912807] nouveau 0000:03:00.0: PCI INT A -> Link[LNK1] -> GSI 18 (level, low) -> IRQ 18
[    3.912813] nouveau 0000:03:00.0: setting latency timer to 64
[    3.914622] vga16fb: initializing
[    3.914626] vga16fb: mapped to 0xc00a0000
[    3.914663] [drm] nouveau 0000:03:00.0: Detected an NV40 generation card (0x04b300b1)
[    3.914675] fb0: VGA16 VGA frame buffer device
[    3.915022] [drm] nouveau 0000:03:00.0: Attempting to load BIOS image from PROM
[    4.022400] usb 2-7: configuration #1 chosen from 1 choice
[    4.034526] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:02.0/usb2/2-7/2-7:1.0/input/input4
[    4.034666] logitech 0003:046D:C517.0002: input,hidraw1: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:02.0-7/input0
[    4.044318] logitech 0003:046D:C517.0003: fixing up Logitech keyboard report descriptor
[    4.044929] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:02.0/usb2/2-7/2-7:1.1/input/input5
[    4.045098] logitech 0003:046D:C517.0003: input,hiddev96,hidraw2: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:02.0-7/input1
[    4.136613] [drm] nouveau 0000:03:00.0: ... appears to be valid
[    4.136616] [drm] nouveau 0000:03:00.0: BIT BIOS found
[    4.136619] [drm] nouveau 0000:03:00.0: Bios version 05.73.22.51
[    4.136622] [drm] nouveau 0000:03:00.0: TMDS table script pointers not stubbed
[    4.136624] [drm] nouveau 0000:03:00.0: BIT table 'd' not found
[    4.136626] [drm] nouveau 0000:03:00.0: Found Display Configuration Block version 3.0
[    4.136630] [drm] nouveau 0000:03:00.0: DCB connector table: VHER 0x30 5 10 2
[    4.136633] [drm] nouveau 0000:03:00.0:   0: 0x00001030: type 0x30 idx 0 tag 0x07
[    4.136635] [drm] nouveau 0000:03:00.0:   1: 0x00002130: type 0x30 idx 1 tag 0x08
[    4.136638] [drm] nouveau 0000:03:00.0:   2: 0x00000210: type 0x10 idx 2 tag 0xff
[    4.136640] [drm] nouveau 0000:03:00.0:   3: 0x00000211: type 0x11 idx 2 tag 0xff
[    4.136642] [drm] nouveau 0000:03:00.0:   4: 0x00000213: type 0x13 idx 2 tag 0xff
[    4.136645] [drm] nouveau 0000:03:00.0: Raw DCB entry 0: 01000300 00000028
[    4.136648] [drm] nouveau 0000:03:00.0: Raw DCB entry 1: 03000302 00000000
[    4.136650] [drm] nouveau 0000:03:00.0: Raw DCB entry 2: 04011310 00000028
[    4.136652] [drm] nouveau 0000:03:00.0: Raw DCB entry 3: 04011312 00000000
[    4.136654] [drm] nouveau 0000:03:00.0: Raw DCB entry 4: 020223f1 00c0c080
[    4.136662] [drm] nouveau 0000:03:00.0: Parsing VBIOS init table 0 at offset 0xCE4D
[    4.136992] [drm] nouveau 0000:03:00.0: Parsing VBIOS init table 1 at offset 0xD4F7
[    4.184037] [drm] nouveau 0000:03:00.0: Parsing VBIOS init table 2 at offset 0xDBFE
[    4.184057] [drm] nouveau 0000:03:00.0: Parsing VBIOS init table 3 at offset 0xDD82
[    4.208024] [drm] nouveau 0000:03:00.0: Parsing VBIOS init table 4 at offset 0xDEFA
[    4.241648] Console: switching to colour frame buffer device 80x30
[    4.264720] [TTM] Zone  kernel: Available graphics memory: 436888 kiB.
[    4.264723] [TTM] Zone highmem: Available graphics memory: 1030236 kiB.
[    4.264732] [drm] nouveau 0000:03:00.0: 128 MiB VRAM
[    4.267938] [drm] nouveau 0000:03:00.0: 64 MiB GART (aperture)
[    4.269370] [drm] nouveau 0000:03:00.0: Allocating FIFO number 0
[    4.273756] [drm] nouveau 0000:03:00.0: nouveau_channel_alloc: initialised FIFO 0
[    4.273765] [drm] nouveau 0000:03:00.0: Initial CRTC_OWNER is 0
[    4.273814] [drm] nouveau 0000:03:00.0: Detected a DVI-I connector
[    4.273875] [drm] nouveau 0000:03:00.0: Detected a DVI-I connector
[    4.273898] [drm] nouveau 0000:03:00.0: Detected a TV connector
[    4.275577] [drm] nouveau 0000:03:00.0: Setting dpms mode 3 on vga encoder (output 0)
[    4.275580] [drm] nouveau 0000:03:00.0: Setting dpms mode 3 on tmds encoder (output 1)
[    4.275583] [drm] nouveau 0000:03:00.0: Setting dpms mode 3 on vga encoder (output 2)
[    4.275586] [drm] nouveau 0000:03:00.0: Setting dpms mode 3 on tmds encoder (output 3)
[    4.275588] [drm] nouveau 0000:03:00.0: Setting dpms mode 3 on TV encoder (output 4)
[    4.464260] [drm] nouveau 0000:03:00.0: allocated 1920x1200 fb: 0x49000, bo f70dae00
[    4.464316] fb1: nouveaufb frame buffer device
[    4.464317] registered panic notifier
[    4.464322] [drm] Initialized nouveau 0.0.15 20090420 for 0000:03:00.0 on minor 1
[    4.668510] xor: automatically using best checksumming function: pIII_sse
[    4.688000]    pIII_sse  :  8623.000 MB/sec
[    4.688003] xor: using function: pIII_sse (8623.000 MB/sec)
[    4.690454] device-mapper: dm-raid45: initialized v0.2594b
[    4.797799] EXT4-fs (sda1): mounted filesystem with ordered data mode
[    4.904921] EXT4-fs (sda3): mounted filesystem with ordered data mode
[    7.936204] usb-storage: device scan complete
[   10.028552] scsi 4:0:0:0: Direct-Access     WDC WD32 00AAKS-00VYA0         PQ: 0 ANSI: 2
[   10.028972] sd 4:0:0:0: Attached scsi generic sg2 type 0
[   10.030415] sd 4:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[   10.033661] sd 4:0:0:0: [sdb] Write Protect is off
[   10.033664] sd 4:0:0:0: [sdb] Mode Sense: 38 00 00 00
[   10.033666] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[   10.037660] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[   10.037664]  sdb: sdb1
[   10.050664] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[   10.050667] sd 4:0:0:0: [sdb] Attached SCSI disk
[   11.351844] sr 2:0:0:0: [sr0] Unhandled sense code
[   11.351848] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   11.351852] sr 2:0:0:0: [sr0] Sense Key : Medium Error [current]
[   11.351857] sr 2:0:0:0: [sr0] Add. Sense: L-EC uncorrectable error
[   11.351862] sr 2:0:0:0: [sr0] CDB: Read(10): 28 00 00 05 76 70 00 00 02 00
[   11.351870] end_request: I/O error, dev sr0, sector 1432000
[   11.351873] Buffer I/O error on device sr0, logical block 179000
[   16.197346] sr 2:0:0:0: [sr0] Unhandled sense code
[   16.197348] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   16.197351] sr 2:0:0:0: [sr0] Sense Key : Medium Error [current]
[   16.197354] sr 2:0:0:0: [sr0] Add. Sense: L-EC uncorrectable error
[   16.197357] sr 2:0:0:0: [sr0] CDB: Read(10): 28 00 00 05 76 70 00 00 02 00
[   16.197364] end_request: I/O error, dev sr0, sector 1432000
[   16.197366] Buffer I/O error on device sr0, logical block 179000
[   21.044053] sr 2:0:0:0: [sr0] Unhandled sense code
[   21.044055] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   21.044058] sr 2:0:0:0: [sr0] Sense Key : Medium Error [current]
[   21.044061] sr 2:0:0:0: [sr0] Add. Sense: L-EC uncorrectable error
[   21.044064] sr 2:0:0:0: [sr0] CDB: Read(10): 28 00 00 05 76 70 00 00 02 00
[   21.044071] end_request: I/O error, dev sr0, sector 1432000
[   21.044073] Buffer I/O error on device sr0, logical block 179000
[   25.890673] sr 2:0:0:0: [sr0] Unhandled sense code
[   25.890675] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   25.890677] sr 2:0:0:0: [sr0] Sense Key : Medium Error [current]
[   25.890680] sr 2:0:0:0: [sr0] Add. Sense: L-EC uncorrectable error
[   25.890684] sr 2:0:0:0: [sr0] CDB: Read(10): 28 00 00 05 76 70 00 00 02 00
[   25.890690] end_request: I/O error, dev sr0, sector 1432000
[   25.890693] Buffer I/O error on device sr0, logical block 179000
[   30.737319] sr 2:0:0:0: [sr0] Unhandled sense code
[   30.737320] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   30.737323] sr 2:0:0:0: [sr0] Sense Key : Medium Error [current]
[   30.737326] sr 2:0:0:0: [sr0] Add. Sense: L-EC uncorrectable error
[   30.737330] sr 2:0:0:0: [sr0] CDB: Read(10): 28 00 00 05 76 70 00 00 02 00
[   30.737336] end_request: I/O error, dev sr0, sector 1432000
[   30.737339] Buffer I/O error on device sr0, logical block 179000
[   35.585208] sr 2:0:0:0: [sr0] Unhandled sense code
[   35.585210] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   35.585213] sr 2:0:0:0: [sr0] Sense Key : Medium Error [current]
[   35.585216] sr 2:0:0:0: [sr0] Add. Sense: L-EC uncorrectable error
[   35.585219] sr 2:0:0:0: [sr0] CDB: Read(10): 28 00 00 05 76 70 00 00 02 00
[   35.585226] end_request: I/O error, dev sr0, sector 1432000
[   35.585231] Buffer I/O error on device sr0, logical block 179000
[   40.430558] sr 2:0:0:0: [sr0] Unhandled sense code
[   40.430560] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   40.430563] sr 2:0:0:0: [sr0] Sense Key : Medium Error [current]
[   40.430566] sr 2:0:0:0: [sr0] Add. Sense: L-EC uncorrectable error
[   40.430569] sr 2:0:0:0: [sr0] CDB: Read(10): 28 00 00 05 76 70 00 00 02 00
[   40.430576] end_request: I/O error, dev sr0, sector 1432000
[   40.430580] Buffer I/O error on device sr0, logical block 179000
[   45.428633] sr 2:0:0:0: [sr0] Unhandled sense code
[   45.428635] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   45.428638] sr 2:0:0:0: [sr0] Sense Key : Medium Error [current]
[   45.428641] sr 2:0:0:0: [sr0] Add. Sense: L-EC uncorrectable error
[   45.428644] sr 2:0:0:0: [sr0] CDB: Read(10): 28 00 00 05 76 70 00 00 02 00
[   45.428651] end_request: I/O error, dev sr0, sector 1432000
[   45.428655] Buffer I/O error on device sr0, logical block 179000
[   50.275199] sr 2:0:0:0: [sr0] Unhandled sense code
[   50.275201] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   50.275204] sr 2:0:0:0: [sr0] Sense Key : Medium Error [current]
[   50.275207] sr 2:0:0:0: [sr0] Add. Sense: L-EC uncorrectable error
[   50.275210] sr 2:0:0:0: [sr0] CDB: Read(10): 28 00 00 05 76 70 00 00 02 00
[   50.275217] end_request: I/O error, dev sr0, sector 1432000
[   50.275222] Buffer I/O error on device sr0, logical block 179000
[   55.159564] sr 2:0:0:0: [sr0] Unhandled sense code
[   55.159566] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   55.159569] sr 2:0:0:0: [sr0] Sense Key : Medium Error [current]
[   55.159572] sr 2:0:0:0: [sr0] Add. Sense: L-EC uncorrectable error
[   55.159575] sr 2:0:0:0: [sr0] CDB: Read(10): 28 00 00 05 76 70 00 00 02 00
[   55.159582] end_request: I/O error, dev sr0, sector 1432000
[   55.159587] Buffer I/O error on device sr0, logical block 179000
[   56.405562] ISO 9660 Extensions: Microsoft Joliet Level 3
[   56.469141] ISO 9660 Extensions: RRIP_1991A
[   56.842864] aufs 2-standalone.tree-20091207
[   56.894830] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[   58.195066] aufs test_add:243:exe[482]: uid/gid/perm //filesystem.squashfs 1000/1000/0755, 0/0/0755
[  187.722504] Adding 6032368k swap on /dev/sda5.  Priority:-1 extents:1 across:6032368k
[  190.994947] udev: starting version 151
[  205.392813] i2c i2c-2: nForce2 SMBus adapter at 0x2040
[  205.392839] i2c i2c-3: nForce2 SMBus adapter at 0x2000
[  206.994630] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[  206.998884] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[  208.950136] dell-wmi: No known WMI GUID found
[  213.303024]   alloc irq_desc for 28 on node -1
[  213.303027]   alloc kstat_irqs on node -1
[  213.303040] tg3 0000:02:00.0: irq 28 for MSI/MSI-X
[  213.348466] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  214.899857] tg3: eth0: Link is up at 100 Mbps, full duplex.
[  214.899861] tg3: eth0: Flow control is on for TX and on for RX.
[  214.900066] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  225.273519] eth0: no IPv6 routers present
[  225.782411] usbcore: registered new interface driver snd-usb-audio　

オフライン

 

#8 2010-05-14 12:11:15

gontomo
メンバ
From: 北海道
登録日: 2010-02-17

Re: 10.04LTS ライブCDの立ち上がり時間について

[   11.351844] sr 2:0:0:0: [sr0] Unhandled sense code
[   11.351848] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   11.351852] sr 2:0:0:0: [sr0] Sense Key : Medium Error [current]
[   11.351857] sr 2:0:0:0: [sr0] Add. Sense: L-EC uncorrectable error
[   11.351862] sr 2:0:0:0: [sr0] CDB: Read(10): 28 00 00 05 76 70 00 00 02 00
[   11.351870] end_request: I/O error, dev sr0, sector 1432000
[   11.351873] Buffer I/O error on device sr0, logical block 179000

CDの読み込みエラーが出てますね。
同じマシンで、9.10の時は速いのであれば、ドライブ側の読み取り問題ではなくて、10.04のメディア側の問題だと思います。
10.04のメディアを焼いたときのドライブか、メディア(ディスク)そのものの問題じゃないでしょうか。

オフライン

 

#9 2010-05-14 12:59:12

hiropack
メンバ
登録日: 2009-02-27

Re: 10.04LTS ライブCDの立ち上がり時間について

今コンビニにて新しいCDーR買ってきて焼いてみたんですが、同じエラーでてます。ただ立ち上がりは１０分に短縮しましたが。

9.10 も 10.04も同じドライブで焼いています、、、ただ時間差はありますので、それまでに壊れたといわれれば何とも言えないのですが。

もう一度ダウンロードし直して焼いてみます。　　もう一大書き込みできるドライブがあればいいんですが。

オフライン

 

#10 2010-05-14 13:43:21

y.n.(beta)
メンバ
From: japan
登録日: 2009-10-21

Re: 10.04LTS ライブCDの立ち上がり時間について

ﾜﾀｸｼは初心者で、似たような経験があります。
（数十枚ほど失敗してます…）

ファイルを焼くソフトにチェックやテストをさせないようにオプションを切っておく、とか。
（データが壊れないように）

.iso ファイルを落とすときは、最上階のフォルダに、とか。
（無関係だと思いますが、日本語ファイル名トラブルを避けて）

.iso ファイルを落としたあと、ファイルを移動させない＆マシン再起動させてから焼く、とか。
（キャッシュが利いていたりして、純粋なファイルの移動ではなかったりしそうなので）

素人のﾜﾀｸｼの焼きの経験ですので、無視して頂いた方が良いかも。
失礼しました。

オフライン

 

#11 2010-05-14 14:16:20

gontomo
メンバ
From: 北海道
登録日: 2010-02-17

Re: 10.04LTS ライブCDの立ち上がり時間について

USBメモリでLiveUSBをつくって起動するっていうのも手だと思います。

オフライン

 

#12 2010-05-14 14:23:29

weyk
メンバ
登録日: 2009-04-03

Re: 10.04LTS ライブCDの立ち上がり時間について

一応、１項目だけ。

ファイルを焼くソフトにチェックやテストをさせないようにオプションを切っておく、とか。
（データが壊れないように）

書き込みテスト(テストやコンペア)は、やっておくことをお勧めします。
もし、これが壊れる原因になるようであれば、おそらく、１度とかの使用で壊れますし。
# アナログレコードのように、再生するたびに大きく磨耗してゆく媒体とか、コアメモリのように読み出すと確実に消えてしまうメディア(?)は別です・・・
事前に行われるチェックであれば、飛ばしても影響は少ないです。そこのチェックでひっかかる内容であれば、書き込みそのものが失敗すると思っています(転送が追いつかない　とか、そういったケースになるかなと)

# 他の要素は、おそらくは関係ないとは思いますが、デメリットも無いと思われるので、好みに応じていろいろ試すのが良いかと思います。


　また、ダウンロードしなおす場合には、そのつど、チェックサム(md5?)により、ファイルが正しいかどうかをチェックすることをお勧めします。事前に個々で１度確認しておけば、その後でうまくゆかない場合でも、その後の作業からを考慮すればすみますから。
# チェックが正しければ、ダウンロードしたファイルは正しい可能性が高いです(100%正しいわけでは有りません)。が、チェックが異なっていれば、確実に壊れていますから、その先の書き込みと起動を試すことなく、再度ダウンロードすればよい　ということになります。

　また、エラーの位置(先頭から700MBytes付近っぽい?)ということを考えると、なんとなく、CD-Rの限界帯付近のような気がします。ひょとすると、びみょーに10.4のほうが総サイズが大きくて、急激に不安定になっている　のかもしれません(サイズは未確認です。10.4のほうが小さければ、この可能性は考慮しなくても良い・・・と思います)
※CD-Rのメディアかもしれませんし、書き込み側のドライブかも知れませんし、読み込み側のドライブかもしれません。CD自体は、最初は、74分(650MBytes)の仕様だった気がしますし。
可能であれば、メディアの大きな容量(700Mか、できれば720M?)を謳っているもので、信頼性の高いメーカのものを用いてください。ドライブが原因だとどーにもなりませんが・・・確認が可能でしたら、書き込み側と読み取り側のドライブの仕様上の最大容量(650/700/720のいずれか?)を確認してみてください(私自身は確認したことが無いので、これらの値が仕様に載っているものなのかどうかも判らないです。)


ただの思いつきなのですが、CD-Rの容量限界の問題だとすると、DVD-Rであれば、回避できるんでしょうか・・・？

オフライン

 

#13 2010-05-14 14:49:16

gontomo
メンバ
From: 北海道
登録日: 2010-02-17

Re: 10.04LTS ライブCDの立ち上がり時間について

10.04日本語Remixで、ギリギリ699MBですね。 オリジナル版のほうが若干小さいですが、ドングリです。
一昔前の粗悪メディアだったら容量限界ギリギリサイズだと焼きミスはよくでましたが、最近はどうなんですかね？
近年もっぱらDVD-Rしか使っていないので分からんです。


CD-Rの容量限界の問題だとすると、DVD-Rであれば、回避できるんでしょうか・・・？

容量限界付近における焼きミスが原因ならDVD-Rであれば問題ないでしょうね。

オフライン

 

#14 2010-05-14 16:28:01

hmatsue
アドバイザ
登録日: 2009-03-10

Re: 10.04LTS ライブCDの立ち上がり時間について

gontomo による投稿:

USBメモリでLiveUSBをつくって起動するっていうのも手だと思います。

gontomoさんの案に一票です。
もし、これでもダメなら、真面目にバグであったりしないか、調べてみる必要があるかと思います。
# ふと思ったのですが、CD-Rに焼くときにセッションのクローズをしていないとかはないでしょうか。
# また、理屈はよく判りませんが、メディアのサイズギリギリの場合、ドライブやライティングソフト
# によっては書き込みに失敗しやくするなるという噂を聞いたことがあります
# (真偽の程は定かではありません)。

オフライン

 

#15 2010-05-14 20:03:26

hiropack
メンバ
登録日: 2009-02-27

Re: 10.04LTS ライブCDの立ち上がり時間について

皆さんはDVDに書き込まれているんでしょうか？自分手持ちの生DVD切らしてますので、後で入手テストしてみます。
USBへのインストールは、私のこのマシンUSBブート未対応でして（今時）、残念ながら対象外なのです。

またこのドライブのダイアグノスティック、DELLよりダウンロードしてかけてみましたが、書き込みテスト項目がなく、切り分けできませんでした。
しかしコントローラーなど他の部分のテストはすべてクリアーしてます。　ですので１００％ではないですが、ドライブが起因の確率は少し減りました。

Ubuntuのデータが壊れている事は考えにくい。
生CD６枚に対して同じ状況である。

ということを踏まえますと

１　データサイズがギリギリすぎる、
２　書き込みドライブの問題。　得に問題はなさそうではありますが。
３　書き込みソフト(Bracero)に問題あり、　　
位しか残らなく一番怪しいのはデータサイズとなってくるんでしょうか？

因みに、焼いた後セッションクローズはしてます。　そして私もメディアのサイズパツンパツンの時、ドライブとライティングソフト
によっては書き込みに失敗しやくするなるという噂を聞いたことがあります。ですのでこれを非常に疑ってます。

バグ情報も調べてみないといけないかもしれません。。。

もう一台あった書き込みのできるPCは先週末、実家に送ってしまい手元になくテストできず。（1週間待てばよかった、ガク！）

オフライン

 

#16 2010-05-14 20:41:03

hito
管理者
登録日: 2007-03-18

Re: 10.04LTS ライブCDの立ち上がり時間について

[   11.351844] sr 2:0:0:0: [sr0] Unhandled sense code
[   11.351848] sr 2:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   11.351852] sr 2:0:0:0: [sr0] Sense Key : Medium Error [current]
[   11.351857] sr 2:0:0:0: [sr0] Add. Sense: L-EC uncorrectable error
[   11.351862] sr 2:0:0:0: [sr0] CDB: Read(10): 28 00 00 05 76 70 00 00 02 00
[   11.351870] end_request: I/O error, dev sr0, sector 1432000

どうも https://bugs.launchpad.net/ubuntu/+source/linux/+bug/577465 に同じものがいるような気がします（ただしsense keyが違うので別の現象の可能性はある）。

「以前にうまく動いていたことが確定しているISOイメージ」を新規に焼いてみて、それで動かなければ何かしらのドライババグを疑ってみる（か、CDなんか使わないから知らないという判断のもと、とりあえずインストールしてしまう）のが良さそうです。一般的なメディアエラーにしては、どうもsense keyがおかしいですし。

オフライン

 

#17 2010-05-14 21:59:33

hiropack
メンバ
登録日: 2009-02-27

Re: 10.04LTS ライブCDの立ち上がり時間について

hitoさん、いつもお世話になります。

今DVDに焼いてみました、そしたところ早いです。約3分３０秒で立ち上がりました。

下に　/var/log/dmesg　張り付けます。　　CDの時に出ていたエラーがDVDの場合では出てません。　

って事は、CDへ焼くときのみのバグって事になるんでしょうか？　７００MBの生ディスク使ってます。論理的にはOKな筈なんでしょうけど。。。他でCDに焼いていらっしゃる方もいると思うんですが、問題なくたちあがってるんでしょうか？　とすれば私のマシン上でのドライブとライティングソフトの組み合わせのみで発生するという訳の分からない状況になってしまうんですが。

教えていたいただバグレポート除いてみましたが、一点気になりました。私のDVDデバイスもこのレポートをあげている人と同じ Samsung 製です。　具体的に起きている現象は少し違うようですが、根底では同じところに原因あるのでしょうかね？


[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.32-21-generic (buildd@rothera) (gcc version 4.4.3 (Ubuntu 4.4.3-4ubuntu5) ) #32-Ubuntu SMP Fri Apr 16 08:10:02 UTC 2010 (Ubuntu 2.6.32-21.32-generic 2.6.32.11+drm33.2)
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   NSC Geode by NSC
[    0.000000]   Cyrix CyrixInstead
[    0.000000]   Centaur CentaurHauls
[    0.000000]   Transmeta GenuineTMx86
[    0.000000]   Transmeta TransmetaCPU
[    0.000000]   UMC UMC UMC UMC
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
[    0.000000]  BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000007fee0000 (usable)
[    0.000000]  BIOS-e820: 000000007fee0000 - 000000007fee5000 (ACPI data)
[    0.000000]  BIOS-e820: 000000007fee5000 - 000000007ff7f000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved)
[    0.000000]  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[    0.000000] DMI present.
[    0.000000] last_pfn = 0x7fee0 max_arch_pfn = 0x100000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CEFFF write-protect
[    0.000000]   CF000-E3FFF uncachable
[    0.000000]   E4000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000000 mask FFFF80000000 write-back
[    0.000000]   1 disabled
[    0.000000]   2 disabled
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820 update range: 0000000000002000 - 0000000000006000 (usable) ==> (reserved)
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] modified physical RAM map:
[    0.000000]  modified: 0000000000000000 - 0000000000002000 (usable)
[    0.000000]  modified: 0000000000002000 - 0000000000006000 (reserved)
[    0.000000]  modified: 0000000000006000 - 000000000009dc00 (usable)
[    0.000000]  modified: 000000000009dc00 - 00000000000a0000 (reserved)
[    0.000000]  modified: 00000000000ce000 - 0000000000100000 (reserved)
[    0.000000]  modified: 0000000000100000 - 000000007fee0000 (usable)
[    0.000000]  modified: 000000007fee0000 - 000000007fee5000 (ACPI data)
[    0.000000]  modified: 000000007fee5000 - 000000007ff7f000 (ACPI NVS)
[    0.000000]  modified: 000000007ff80000 - 0000000080000000 (reserved)
[    0.000000]  modified: 00000000e0000000 - 00000000f0000000 (reserved)
[    0.000000]  modified: 00000000fec00000 - 00000000fec10000 (reserved)
[    0.000000]  modified: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  modified: 00000000fff80000 - 0000000100000000 (reserved)
[    0.000000] initial memory mapped : 0 - 00c00000
[    0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[    0.000000] Using x86 segment limits to approximate NX protection
[    0.000000]  0000000000 - 0000400000 page 4k
[    0.000000]  0000400000 - 0037400000 page 2M
[    0.000000]  0037400000 - 00377fe000 page 4k
[    0.000000] kernel direct mapping tables up to 377fe000 @ 7000-c000
[    0.000000] RAMDISK: 7f5c1000 - 7feaf970
[    0.000000] Allocated new RAMDISK: 008de000 - 011cc970
[    0.000000] Move RAMDISK from 000000007f5c1000 - 000000007feaf96f to 008de000 - 011cc96f
[    0.000000] ACPI: RSDP 000f79b0 00024 (v02 PTLTD )
[    0.000000] ACPI: XSDT 7fee077b 0009C (v01 DELL   PE_SC3   06040000 DELL 00000000)
[    0.000000] ACPI: FACP 7fee3c87 000F4 (v03 DELL   PE_SC3   06040000 DELL 000F4240)
[    0.000000] ACPI: DSDT 7fee0817 033FC (v01 DELL   PE_SC3   06040000 MSFT 0100000E)
[    0.000000] ACPI: FACS 7fee5fc0 00040
[    0.000000] ACPI: TCPA 7fee3d7b 00032 (v01 Phoeni  x       06040000  TL  00000000)
[    0.000000] ACPI: SLIC 7fee3dad 00024 (v01 DELL   PE_SC3   06040000 PTL  00000001)
[    0.000000] ACPI: SPCR 7fee3dd1 00050 (v01 DELL   PE_SC3   06040000 PTL  00000001)
[    0.000000] ACPI: EINJ 7fee3e21 001B0 (v01 PTL    WHEAPTL  06040000 PTL  00000001)
[    0.000000] ACPI: HEST 7fee3fd1 000A8 (v01 PTL    WHEAPTL  06040000 PTL  00000001)
[    0.000000] ACPI: BERT 7fee4079 00030 (v01 PTL    WHEAPTL  06040000 PTL  00000001)
[    0.000000] ACPI: SSDT 7fee40a9 000E1 (v01 wheaos  wheaosc 06040000 INTL 20050624)
[    0.000000] ACPI: ERST 7fee418a 00270 (v01 PTL    WHEAPTL  06040000 PTL  00000001)
[    0.000000] ACPI: SRAT 7fee43fa 000C0 (v01 AMD    HAMMER   06040000 AMD  00000001)
[    0.000000] ACPI: SSDT 7fee44ba 00A30 (v01 AMD    POWERNOW 06040000 AMD  00000001)
[    0.000000] ACPI: MCFG 7fee4eea 0003C (v01 PTLTD    MCFG   06040000  LTP 00000000)
[    0.000000] ACPI: HPET 7fee4f26 00038 (v01 PTLTD  HPETTBL  06040000  LTP 00000001)
[    0.000000] ACPI: APIC 7fee4f5e 0007A (v01 PTLTD  ? APIC   06040000  LTP 00000000)
[    0.000000] ACPI: BOOT 7fee4fd8 00028 (v01 PTLTD  $SBFTBL$ 06040000  LTP 00000001)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 1158MB HIGHMEM available.
[    0.000000] 887MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 377fe000
[    0.000000]   low ram: 0 - 377fe000
[    0.000000]   node 0 low ram: 00000000 - 377fe000
[    0.000000]   node 0 bootmap 00008000 - 0000ef00
[    0.000000] (9 early reservations) ==> bootmem [0000000000 - 00377fe000]
[    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
[    0.000000]   #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
[    0.000000]   #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
[    0.000000]   #3 [0000100000 - 00008d9e98]    TEXT DATA BSS ==> [0000100000 - 00008d9e98]
[    0.000000]   #4 [000009dc00 - 0000100000]    BIOS reserved ==> [000009dc00 - 0000100000]
[    0.000000]   #5 [00008da000 - 00008dd0e4]              BRK ==> [00008da000 - 00008dd0e4]
[    0.000000]   #6 [0000007000 - 0000008000]          PGTABLE ==> [0000007000 - 0000008000]
[    0.000000]   #7 [00008de000 - 00011cc970]      NEW RAMDISK ==> [00008de000 - 00011cc970]
[    0.000000]   #8 [0000008000 - 000000f000]          BOOTMAP ==> [0000008000 - 000000f000]
[    0.000000] found SMP MP-table at [c00f7a70] f7a70
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000000 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x000377fe
[    0.000000]   HighMem  0x000377fe -> 0x0007fee0
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[3] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00000002
[    0.000000]     0: 0x00000006 -> 0x0000009d
[    0.000000]     0: 0x00000100 -> 0x0007fee0
[    0.000000] On node 0 totalpages: 523897
[    0.000000] free_area_init_node: node 0, pgdat c0798720, node_mem_map c11ce000
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3961 pages, LIFO batch:0
[    0.000000]   Normal zone: 1744 pages used for memmap
[    0.000000]   Normal zone: 221486 pages, LIFO batch:31
[    0.000000]   HighMem zone: 2318 pages used for memmap
[    0.000000]   HighMem zone: 294356 pages, LIFO batch:31
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x8008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
[    0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 24
[    0.000000] PM: Registered nosave memory: 0000000000002000 - 0000000000006000
[    0.000000] PM: Registered nosave memory: 000000000009d000 - 000000000009e000
[    0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000ce000
[    0.000000] PM: Registered nosave memory: 00000000000ce000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:60000000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 14 pages/cpu @c2400000 s36024 r0 d21320 u1048576
[    0.000000] pcpu-alloc: s36024 r0 d21320 u1048576 alloc=1*4194304
[    0.000000] pcpu-alloc: [0] 0 1 2 3
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 519803
[    0.000000] Kernel command line: BOOT_IMAGE=/casper/vmlinuz file=/cdrom/preseed/ubuntu.seed boot=casper initrd=/casper/initrd.lz quiet splash -- debian-installer/language=ja console-setup/layoutcode?=jp console-setup/modelcode?=jp106 maybe-ubiquity
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] allocated 10480000 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Initializing HighMem for node 0 (000377fe:0007fee0)
[    0.000000] Memory: 2049616k/2096000k available (4673k kernel code, 44916k reserved, 2122k data, 656k init, 1186696k highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xfff1d000 - 0xfffff000   ( 904 kB)
[    0.000000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.000000]     vmalloc : 0xf7ffe000 - 0xff7fe000   ( 120 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf77fe000   ( 887 MB)
[    0.000000]       .init : 0xc07a3000 - 0xc0847000   ( 656 kB)
[    0.000000]       .data : 0xc0590613 - 0xc07a2e48   (2122 kB)
[    0.000000]       .text : 0xc0100000 - 0xc0590613   (4673 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:2304 nr_irqs:440
[    0.000000] Extended CMOS year: 2000
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] hpet clockevent registered
[    0.000000] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 2109.368 MHz processor.
[    0.004005] Calibrating delay loop (skipped), value calculated using timer frequency.. 4218.73 BogoMIPS (lpj=8437472)
[    0.004021] Security Framework initialized
[    0.004038] AppArmor: AppArmor initialized
[    0.004045] Mount-cache hash table entries: 512
[    0.004149] Initializing cgroup subsys ns
[    0.004153] Initializing cgroup subsys cpuacct
[    0.004157] Initializing cgroup subsys memory
[    0.004163] Initializing cgroup subsys devices
[    0.004165] Initializing cgroup subsys freezer
[    0.004168] Initializing cgroup subsys net_cls
[    0.004183] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[    0.004186] CPU: L2 Cache: 512K (64 bytes/line)
[    0.004188] CPU: Physical Processor ID: 0
[    0.004189] CPU: Processor Core ID: 0
[    0.004193] mce: CPU supports 6 MCE banks
[    0.004202] using C1E aware idle routine
[    0.004207] Performance Events: AMD PMU driver.
[    0.004212] ... version:                0
[    0.004214] ... bit width:              48
[    0.004216] ... generic registers:      4
[    0.004218] ... value mask:             0000ffffffffffff
[    0.004220] ... max period:             00007fffffffffff
[    0.004222] ... fixed-purpose events:   0
[    0.004224] ... event mask:             000000000000000f
[    0.004227] Checking 'hlt' instruction... OK.
[    0.022153] ACPI: Core revision 20090903
[    0.028008] ftrace: converting mcount calls to 0f 1f 44 00 00
[    0.028013] ftrace: allocating 21771 entries in 43 pages
[    0.032061] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.032342] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.074855] CPU0: Quad-Core AMD Opteron(tm) Processor 1352 stepping 03
[    0.076001] Booting processor 1 APIC 0x1 ip 0x6000
[    0.008000] Initializing CPU#1
[    0.008000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[    0.008000] CPU: L2 Cache: 512K (64 bytes/line)
[    0.008000] CPU: Physical Processor ID: 0
[    0.008000] CPU: Processor Core ID: 1
[    0.160035] CPU1: Quad-Core AMD Opteron(tm) Processor 1352 stepping 03
[    0.160046] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[    0.164067] Booting processor 2 APIC 0x2 ip 0x6000
[    0.008000] Initializing CPU#2
[    0.008000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[    0.008000] CPU: L2 Cache: 512K (64 bytes/line)
[    0.008000] CPU: Physical Processor ID: 0
[    0.008000] CPU: Processor Core ID: 2
[    0.252091] CPU2: Quad-Core AMD Opteron(tm) Processor 1352 stepping 03
[    0.252102] checking TSC synchronization [CPU#0 -> CPU#2]: passed.
[    0.256064] Booting processor 3 APIC 0x3 ip 0x6000
[    0.008000] Initializing CPU#3
[    0.008000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[    0.008000] CPU: L2 Cache: 512K (64 bytes/line)
[    0.008000] CPU: Physical Processor ID: 0
[    0.008000] CPU: Processor Core ID: 3
[    0.344049] CPU3: Quad-Core AMD Opteron(tm) Processor 1352 stepping 03
[    0.344061] checking TSC synchronization [CPU#0 -> CPU#3]: passed.
[    0.348012] Brought up 4 CPUs
[    0.348015] Total of 4 processors activated (16877.18 BogoMIPS).
[    0.349034] CPU0 attaching sched-domain:
[    0.349037]  domain 0: span 0-3 level MC
[    0.349039]   groups: 0 1 2 3
[    0.349046] CPU1 attaching sched-domain:
[    0.349048]  domain 0: span 0-3 level MC
[    0.349050]   groups: 1 2 3 0
[    0.349055] CPU2 attaching sched-domain:
[    0.349057]  domain 0: span 0-3 level MC
[    0.349059]   groups: 2 3 0 1
[    0.349064] CPU3 attaching sched-domain:
[    0.349066]  domain 0: span 0-3 level MC
[    0.349068]   groups: 3 0 1 2
[    0.349171] devtmpfs: initialized
[    0.349171] regulator: core version 0.5
[    0.349171] Time: 21:37:28  Date: 05/14/10
[    0.349171] NET: Registered protocol family 16
[    0.349171] Trying to unpack rootfs image as initramfs...
[    0.349171] EISA bus registered
[    0.349171] ACPI: bus type pci registered
[    0.349171] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 4
[    0.349171] PCI: MCFG area at e0000000 reserved in E820
[    0.349171] PCI: Using MMCONFIG for extended config space
[    0.349171] PCI: Using configuration type 1 for base access
[    0.349171] bio: create slab <bio-0> at 0
[    0.349171] ACPI: EC: Look up EC in DSDT
[    0.352467] ACPI Warning for \_SB_._OSC: Return type mismatch - found Integer, expected Buffer (20090903/nspredef-1006)
[    0.352476] \_SB_:_OSC evaluation returned wrong type
[    0.352478] _OSC request data:1 7
[    0.354547] ACPI: Interpreter enabled
[    0.354552] ACPI: (supports S0 S4 S5)
[    0.354567] ACPI: Using IOAPIC for interrupt routing
[    0.358606] ACPI: No dock devices found.
[    0.358698] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.358783] pci 0000:00:01.0: reg 10 io port: [0x8c00-0x8fff]
[    0.358808] pci 0000:00:01.1: reg 10 io port: [0x2080-0x209f]
[    0.358816] pci 0000:00:01.1: reg 20 io port: [0x2040-0x207f]
[    0.358820] pci 0000:00:01.1: reg 24 io port: [0x2000-0x203f]
[    0.358830] pci 0000:00:01.1: PME# supported from D3hot D3cold
[    0.358834] pci 0000:00:01.1: PME# disabled
[    0.358852] pci 0000:00:02.0: reg 10 32bit mmio: [0xc0000000-0xc0000fff]
[    0.358869] pci 0000:00:02.0: supports D1 D2
[    0.358872] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.358875] pci 0000:00:02.0: PME# disabled
[    0.358892] pci 0000:00:02.1: reg 10 32bit mmio: [0xc0001000-0xc00010ff]
[    0.358913] pci 0000:00:02.1: supports D1 D2
[    0.358915] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.358918] pci 0000:00:02.1: PME# disabled
[    0.358944] pci 0000:00:07.0: reg 10 io port: [0x20f0-0x20f7]
[    0.358948] pci 0000:00:07.0: reg 14 io port: [0x20e0-0x20e3]
[    0.358952] pci 0000:00:07.0: reg 18 io port: [0x20d0-0x20d7]
[    0.358956] pci 0000:00:07.0: reg 1c io port: [0x20c0-0x20c3]
[    0.358960] pci 0000:00:07.0: reg 20 io port: [0x20b0-0x20bf]
[    0.358964] pci 0000:00:07.0: reg 24 32bit mmio: [0xc0002000-0xc0002fff]
[    0.358993] pci 0000:00:08.0: reg 10 io port: [0x2440-0x2447]
[    0.358997] pci 0000:00:08.0: reg 14 io port: [0x2430-0x2433]
[    0.359001] pci 0000:00:08.0: reg 18 io port: [0x2420-0x2427]
[    0.359005] pci 0000:00:08.0: reg 1c io port: [0x2410-0x2413]
[    0.359009] pci 0000:00:08.0: reg 20 io port: [0x2400-0x240f]
[    0.359013] pci 0000:00:08.0: reg 24 32bit mmio: [0xc0003000-0xc0003fff]
[    0.359066] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.359069] pci 0000:00:0b.0: PME# disabled
[    0.359100] pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.359103] pci 0000:00:0c.0: PME# disabled
[    0.359134] pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.359137] pci 0000:00:0d.0: PME# disabled
[    0.359166] pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.359169] pci 0000:00:0e.0: PME# disabled
[    0.359282] pci 0000:01:08.0: reg 10 32bit mmio pref: [0xc8000000-0xcfffffff]
[    0.359287] pci 0000:01:08.0: reg 14 io port: [0x3000-0x30ff]
[    0.359293] pci 0000:01:08.0: reg 18 32bit mmio: [0xc0100000-0xc010ffff]
[    0.359306] pci 0000:01:08.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
[    0.359319] pci 0000:01:08.0: supports D1 D2
[    0.359342] pci 0000:00:09.0: bridge io port: [0x3000-0x3fff]
[    0.359345] pci 0000:00:09.0: bridge 32bit mmio: [0xc0100000-0xc01fffff]
[    0.359348] pci 0000:00:09.0: bridge 32bit mmio pref: [0xc8000000-0xcfffffff]
[    0.359391] pci 0000:02:00.0: reg 10 64bit mmio: [0xc0200000-0xc020ffff]
[    0.359440] pci 0000:02:00.0: PME# supported from D3hot D3cold
[    0.359444] pci 0000:02:00.0: PME# disabled
[    0.359481] pci 0000:00:0b.0: bridge 32bit mmio: [0xc0200000-0xc02fffff]
[    0.359507] pci 0000:03:00.0: reg 10 32bit mmio: [0xc2000000-0xc2ffffff]
[    0.359515] pci 0000:03:00.0: reg 14 64bit mmio pref: [0xd0000000-0xdfffffff]
[    0.359524] pci 0000:03:00.0: reg 1c 64bit mmio: [0xc1000000-0xc1ffffff]
[    0.359529] pci 0000:03:00.0: reg 24 io port: [0x4000-0x407f]
[    0.359535] pci 0000:03:00.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
[    0.359583] pci 0000:00:0c.0: bridge io port: [0x4000-0x4fff]
[    0.359586] pci 0000:00:0c.0: bridge 32bit mmio: [0xc1000000-0xc2ffffff]
[    0.359590] pci 0000:00:0c.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
[    0.359652] pci_bus 0000:00: on NUMA node 0
[    0.359656] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.359721] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
[    0.359755] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT]
[    0.359781] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
[    0.359804] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR2._PRT]
[    0.359825] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR3._PRT]
[    0.375536] ACPI: PCI Interrupt Link [LNK1] (IRQs 16 17 18 19) *0
[    0.375678] ACPI: PCI Interrupt Link [LNK2] (IRQs 16 17 18 19) *0
[    0.375817] ACPI: PCI Interrupt Link [LNK3] (IRQs 16 17 18 19) *0, disabled.
[    0.375955] ACPI: PCI Interrupt Link [LNK4] (IRQs 16 17 18 19) *0, disabled.
[    0.376100] ACPI: PCI Interrupt Link [LNK5] (IRQs 16 17 18 19) *0, disabled.
[    0.376238] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *0
[    0.376375] ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22 23) *0
[    0.376512] ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22 23) *0, disabled.
[    0.376650] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled.
[    0.376787] ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0, disabled.
[    0.376924] ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22 23) *0, disabled.
[    0.377063] ACPI: PCI Interrupt Link [LPID] (IRQs 20 21 22 23) *0, disabled.
[    0.377209] ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22 23) *0
[    0.377352] ACPI: PCI Interrupt Link [LSI1] (IRQs 20 21 22 23) *0
[    0.377495] ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
[    0.377583] vgaarb: device added: PCI:0000:01:08.0,decodes=io+mem,owns=none,locks=none
[    0.377588] vgaarb: device added: PCI:0000:03:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.377591] vgaarb: loaded
[    0.377682] SCSI subsystem initialized
[    0.377707] libata version 3.00 loaded.
[    0.377707] usbcore: registered new interface driver usbfs
[    0.377707] usbcore: registered new interface driver hub
[    0.377707] usbcore: registered new device driver usb
[    0.377707] ACPI: WMI: Mapper loaded
[    0.377707] PCI: Using ACPI for IRQ routing
[    0.377707] NetLabel: Initializing
[    0.377707] NetLabel:  domain hash size = 128
[    0.377707] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.377707] NetLabel:  unlabeled traffic allowed by default
[    0.377707] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[    0.377707] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
[    2.284023] Switching to clocksource tsc
[    2.285656] AppArmor: AppArmor Filesystem Enabled
[    2.285670] pnp: PnP ACPI init
[    2.285685] ACPI: bus type pnp registered
[    2.287897] pnp: PnP ACPI: found 12 devices
[    2.287900] ACPI: ACPI bus type pnp unregistered
[    2.287904] PnPBIOS: Disabled by ACPI PNP
[    2.287917] system 00:00: iomem range 0xffc00000-0xffffffff could not be reserved
[    2.287920] system 00:00: iomem range 0xfec00000-0xfec00fff could not be reserved
[    2.287924] system 00:00: iomem range 0xfee00000-0xfeefffff could not be reserved
[    2.287927] system 00:00: iomem range 0xfed00000-0xfed00fff has been reserved
[    2.287933] system 00:02: iomem range 0xe0000000-0xefffffff has been reserved
[    2.287939] system 00:03: ioport range 0x8000-0x807f has been reserved
[    2.287943] system 00:03: ioport range 0x8080-0x80ff has been reserved
[    2.287945] system 00:03: ioport range 0x8400-0x847f has been reserved
[    2.287948] system 00:03: ioport range 0x8480-0x84ff has been reserved
[    2.287951] system 00:03: ioport range 0x8800-0x887f has been reserved
[    2.287954] system 00:03: ioport range 0x8880-0x88ff has been reserved
[    2.287957] system 00:03: ioport range 0x2040-0x207f has been reserved
[    2.287960] system 00:03: ioport range 0x2000-0x203f has been reserved
[    2.287966] system 00:05: ioport range 0x4d0-0x4d1 has been reserved
[    2.287972] system 00:0a: ioport range 0xc00-0xc7f has been reserved
[    2.312593] Freeing initrd memory: 9146k freed
[    2.322671] pci 0000:00:09.0: PCI bridge, secondary bus 0000:01
[    2.322674] pci 0000:00:09.0:   IO window: 0x3000-0x3fff
[    2.322678] pci 0000:00:09.0:   MEM window: 0xc0100000-0xc01fffff
[    2.322681] pci 0000:00:09.0:   PREFETCH window: 0xc8000000-0xcfffffff
[    2.322685] pci 0000:00:0b.0: PCI bridge, secondary bus 0000:02
[    2.322687] pci 0000:00:0b.0:   IO window: disabled
[    2.322690] pci 0000:00:0b.0:   MEM window: 0xc0200000-0xc02fffff
[    2.322693] pci 0000:00:0b.0:   PREFETCH window: disabled
[    2.322699] pci 0000:03:00.0: BAR 6: can't allocate mem resource [0xe0000000-0xdfffffff]
[    2.322701] pci 0000:00:0c.0: PCI bridge, secondary bus 0000:03
[    2.322704] pci 0000:00:0c.0:   IO window: 0x4000-0x4fff
[    2.322707] pci 0000:00:0c.0:   MEM window: 0xc1000000-0xc2ffffff
[    2.322710] pci 0000:00:0c.0:   PREFETCH window: 0x000000d0000000-0x000000dfffffff
[    2.322714] pci 0000:00:0d.0: PCI bridge, secondary bus 0000:04
[    2.322716] pci 0000:00:0d.0:   IO window: disabled
[    2.322719] pci 0000:00:0d.0:   MEM window: disabled
[    2.322722] pci 0000:00:0d.0:   PREFETCH window: disabled
[    2.322725] pci 0000:00:0e.0: PCI bridge, secondary bus 0000:05
[    2.322727] pci 0000:00:0e.0:   IO window: disabled
[    2.322730] pci 0000:00:0e.0:   MEM window: disabled
[    2.322732] pci 0000:00:0e.0:   PREFETCH window: disabled
[    2.322741] pci 0000:00:09.0: setting latency timer to 64
[    2.322746] pci 0000:00:0b.0: setting latency timer to 64
[    2.322751] pci 0000:00:0c.0: setting latency timer to 64
[    2.322756] pci 0000:00:0d.0: setting latency timer to 64
[    2.322760] pci 0000:00:0e.0: setting latency timer to 64
[    2.322764] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
[    2.322767] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[    2.322770] pci_bus 0000:01: resource 0 io:  [0x3000-0x3fff]
[    2.322773] pci_bus 0000:01: resource 1 mem: [0xc0100000-0xc01fffff]
[    2.322775] pci_bus 0000:01: resource 2 pref mem [0xc8000000-0xcfffffff]
[    2.322778] pci_bus 0000:02: resource 1 mem: [0xc0200000-0xc02fffff]
[    2.322781] pci_bus 0000:03: resource 0 io:  [0x4000-0x4fff]
[    2.322784] pci_bus 0000:03: resource 1 mem: [0xc1000000-0xc2ffffff]
[    2.322787] pci_bus 0000:03: resource 2 pref mem [0xd0000000-0xdfffffff]
[    2.322825] NET: Registered protocol family 2
[    2.322933] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    2.323291] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    2.323855] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    2.324149] TCP: Hash tables configured (established 131072 bind 65536)
[    2.324152] TCP reno registered
[    2.324239] NET: Registered protocol family 1
[    2.324314] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324341] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324374] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324379] pci 0000:00:0b.0: Found disabled HT MSI Mapping
[    2.324387] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324391] pci 0000:00:0b.0: Linking AER extended capability
[    2.324427] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324432] pci 0000:00:0c.0: Found disabled HT MSI Mapping
[    2.324439] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324442] pci 0000:00:0c.0: Linking AER extended capability
[    2.324481] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324486] pci 0000:00:0d.0: Found disabled HT MSI Mapping
[    2.324493] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324496] pci 0000:00:0d.0: Linking AER extended capability
[    2.324537] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324543] pci 0000:00:0e.0: Found disabled HT MSI Mapping
[    2.324550] pci 0000:00:00.0: Found enabled HT MSI Mapping
[    2.324552] pci 0000:00:0e.0: Linking AER extended capability
[    2.324571] pci 0000:03:00.0: Boot video device
[    2.324592] Simple Boot Flag at 0x62 set to 0x1
[    2.324968] cpufreq-nforce2: No nForce2 chipset.
[    2.324992] Scanning for low memory corruption every 60 seconds
[    2.325102] audit: initializing netlink socket (disabled)
[    2.325111] type=2000 audit(1273873050.324:1): initialized
[    2.333656] highmem bounce pool size: 64 pages
[    2.333663] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    2.335429] VFS: Disk quotas dquot_6.5.2
[    2.335491] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    2.336088] fuse init (API version 7.13)
[    2.336177] msgmni has been set to 1705
[    2.336435] alg: No test for stdrng (krng)
[    2.336491] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    2.336495] io scheduler noop registered
[    2.336497] io scheduler anticipatory registered
[    2.336499] io scheduler deadline registered
[    2.336544] io scheduler cfq registered (default)
[    2.336653]   alloc irq_desc for 24 on node -1
[    2.336656]   alloc kstat_irqs on node -1
[    2.336664] pcieport 0000:00:0b.0: irq 24 for MSI/MSI-X
[    2.336669] pcieport 0000:00:0b.0: setting latency timer to 64
[    2.336739]   alloc irq_desc for 25 on node -1
[    2.336741]   alloc kstat_irqs on node -1
[    2.336746] pcieport 0000:00:0c.0: irq 25 for MSI/MSI-X
[    2.336750] pcieport 0000:00:0c.0: setting latency timer to 64
[    2.336816]   alloc irq_desc for 26 on node -1
[    2.336818]   alloc kstat_irqs on node -1
[    2.336823] pcieport 0000:00:0d.0: irq 26 for MSI/MSI-X
[    2.336827] pcieport 0000:00:0d.0: setting latency timer to 64
[    2.336891]   alloc irq_desc for 27 on node -1
[    2.336893]   alloc kstat_irqs on node -1
[    2.336897] pcieport 0000:00:0e.0: irq 27 for MSI/MSI-X
[    2.336901] pcieport 0000:00:0e.0: setting latency timer to 64
[    2.336962] aer 0000:00:0b.0:pcie02: AER service couldn't init device: no _OSC support
[    2.336969] aer 0000:00:0c.0:pcie02: AER service couldn't init device: no _OSC support
[    2.336975] aer 0000:00:0d.0:pcie02: AER service couldn't init device: no _OSC support
[    2.336980] aer 0000:00:0e.0:pcie02: AER service couldn't init device: no _OSC support
[    2.336999] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    2.337023] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    2.337111] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[    2.337115] ACPI: Power Button [PWRB]
[    2.337164] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    2.337172] ACPI: Power Button [PWRF]
[    2.337553] processor LNXCPU:00: registered as cooling_device0
[    2.337584] processor LNXCPU:01: registered as cooling_device1
[    2.337617] processor LNXCPU:02: registered as cooling_device2
[    2.337644] processor LNXCPU:03: registered as cooling_device3
[    2.339582] isapnp: Scanning for PnP cards...
[    2.340755] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    2.340841] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    2.341142] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    2.342135] brd: module loaded
[    2.342580] loop: module loaded
[    2.342655] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[    2.343062] ACPI: PCI Interrupt Link [LTID] enabled at IRQ 23
[    2.343067]   alloc irq_desc for 23 on node -1
[    2.343069]   alloc kstat_irqs on node -1
[    2.343075] pata_acpi 0000:00:07.0: PCI INT A -> Link[LTID] -> GSI 23 (level, low) -> IRQ 23
[    2.343102] pata_acpi 0000:00:07.0: setting latency timer to 64
[    2.343113] pata_acpi 0000:00:07.0: PCI INT A disabled
[    2.343376] ACPI: PCI Interrupt Link [LSI1] enabled at IRQ 22
[    2.343379]   alloc irq_desc for 22 on node -1
[    2.343380]   alloc kstat_irqs on node -1
[    2.343384] pata_acpi 0000:00:08.0: PCI INT A -> Link[LSI1] -> GSI 22 (level, low) -> IRQ 22
[    2.343404] pata_acpi 0000:00:08.0: setting latency timer to 64
[    2.343410] pata_acpi 0000:00:08.0: PCI INT A disabled
[    2.343691] Fixed MDIO Bus: probed
[    2.343723] PPP generic driver version 2.4.2
[    2.343751] tun: Universal TUN/TAP device driver, 1.6
[    2.343753] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    2.343826] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.344052] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 21
[    2.344055]   alloc irq_desc for 21 on node -1
[    2.344057]   alloc kstat_irqs on node -1
[    2.344061] ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUS2] -> GSI 21 (level, low) -> IRQ 21
[    2.344071] ehci_hcd 0000:00:02.1: setting latency timer to 64
[    2.344074] ehci_hcd 0000:00:02.1: EHCI Host Controller
[    2.344102] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
[    2.344121] ehci_hcd 0000:00:02.1: debug port 1
[    2.344126] ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
[    2.344140] ehci_hcd 0000:00:02.1: irq 21, io mem 0xc0001000
[    2.356019] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
[    2.356091] usb usb1: configuration #1 chosen from 1 choice
[    2.356116] hub 1-0:1.0: USB hub found
[    2.356125] hub 1-0:1.0: 9 ports detected
[    2.356184] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.356404] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 20
[    2.356406]   alloc irq_desc for 20 on node -1
[    2.356408]   alloc kstat_irqs on node -1
[    2.356412] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 20 (level, low) -> IRQ 20
[    2.356421] ohci_hcd 0000:00:02.0: setting latency timer to 64
[    2.356423] ohci_hcd 0000:00:02.0: OHCI Host Controller
[    2.356449] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[    2.356465] ohci_hcd 0000:00:02.0: irq 20, io mem 0xc0000000
[    2.414071] usb usb2: configuration #1 chosen from 1 choice
[    2.414098] hub 2-0:1.0: USB hub found
[    2.414109] hub 2-0:1.0: 9 ports detected
[    2.414151] uhci_hcd: USB Universal Host Controller Interface driver
[    2.414218] PNP: No PS/2 controller found. Probing ports directly.
[    2.417025] serio: i8042 KBD port at 0x60,0x64 irq 1
[    2.417032] serio: i8042 AUX port at 0x60,0x64 irq 12
[    2.417098] mice: PS/2 mouse device common for all mice
[    2.417192] rtc_cmos 00:08: RTC can wake from S4
[    2.417223] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
[    2.417245] rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[    2.417351] device-mapper: uevent: version 1.0.3
[    2.417440] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    2.417549] device-mapper: multipath: version 1.1.0 loaded
[    2.417552] device-mapper: multipath round-robin: version 1.0.0 loaded
[    2.417663] EISA: Probing bus 0 at eisa.0
[    2.417671] Cannot allocate resource for EISA slot 2
[    2.417673] Cannot allocate resource for EISA slot 3
[    2.417676] Cannot allocate resource for EISA slot 4
[    2.417683] Cannot allocate resource for EISA slot 8
[    2.417685] EISA: Detected 0 cards.
[    2.417861] cpuidle: using governor ladder
[    2.417897] cpuidle: using governor menu
[    2.418357] TCP cubic registered
[    2.418518] NET: Registered protocol family 10
[    2.419015] lo: Disabled Privacy Extensions
[    2.419378] NET: Registered protocol family 17
[    2.419406] powernow-k8: Found 1 Quad-Core AMD Opteron(tm) Processor 1352 processors (4 cpu cores) (version 2.20.00)
[    2.419447] powernow-k8:    0 : pstate 0 (2100 MHz)
[    2.419449] powernow-k8:    1 : pstate 1 (1800 MHz)
[    2.419451] powernow-k8:    2 : pstate 2 (1600 MHz)
[    2.419454] powernow-k8:    3 : pstate 3 (1300 MHz)
[    2.419456] powernow-k8:    4 : pstate 4 (1050 MHz)
[    2.432250] Using IPI No-Shortcut mode
[    2.432333] PM: Resume from disk failed.
[    2.432344] registered taskstats version 1
[    2.432582]   Magic number: 10:853:651
[    2.432616] pci_root PNP0A03:00: hash matches
[    2.432619] processor LNXCPU:04: hash matches
[    2.432652] rtc_cmos 00:08: setting system clock to 2010-05-14 21:37:31 UTC (1273873051)
[    2.432655] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    2.432657] EDD information not available.
[    2.693339] isapnp: No Plug & Play device found
[    2.693365] Freeing unused kernel memory: 656k freed
[    2.693703] Write protecting the kernel text: 4676k
[    2.693744] Write protecting the kernel read-only data: 1840k
[    2.712703] udev: starting version 151
[    2.751925] sata_nv 0000:00:07.0: version 3.5
[    2.751940] sata_nv 0000:00:07.0: PCI INT A -> Link[LTID] -> GSI 23 (level, low) -> IRQ 23
[    2.751984] sata_nv 0000:00:07.0: setting latency timer to 64
[    2.752151] Linux agpgart interface v0.103
[    2.755221] scsi0 : sata_nv
[    2.758715] scsi1 : sata_nv
[    2.758924] ata1: SATA max UDMA/133 cmd 0x20f0 ctl 0x20e0 bmdma 0x20b0 irq 23
[    2.758928] ata2: SATA max UDMA/133 cmd 0x20d0 ctl 0x20c0 bmdma 0x20b8 irq 23
[    2.758955] sata_nv 0000:00:08.0: PCI INT A -> Link[LSI1] -> GSI 22 (level, low) -> IRQ 22
[    2.758997] sata_nv 0000:00:08.0: setting latency timer to 64
[    2.759180] scsi2 : sata_nv
[    2.759258] scsi3 : sata_nv
[    2.759384] ata3: SATA max UDMA/133 cmd 0x2440 ctl 0x2430 bmdma 0x2400 irq 22
[    2.759387] ata4: SATA max UDMA/133 cmd 0x2420 ctl 0x2410 bmdma 0x2408 irq 22
[    2.776870] [drm] Initialized drm 1.1.0 20060810
[    2.781775] tg3.c:v3.102 (September 1, 2009)
[    2.782027] ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 19
[    2.782032]   alloc irq_desc for 19 on node -1
[    2.782034]   alloc kstat_irqs on node -1
[    2.782041] tg3 0000:02:00.0: PCI INT A -> Link[LNK2] -> GSI 19 (level, low) -> IRQ 19
[    2.782048] tg3 0000:02:00.0: setting latency timer to 64
[    2.801075] eth0: Tigon3 [partno(BCM95722) rev a200] (PCI Express) MAC address 00:22:19:1b:bc:17
[    2.801079] eth0: attached PHY is 5722/5756 (10/100/1000Base-T Ethernet) (WireSpeed[1])
[    2.801082] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    2.801084] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[    2.856024] usb 1-5: new high speed USB device using ehci_hcd and address 4
[    2.991594] usb 1-5: configuration #1 chosen from 1 choice
[    3.000371] Initializing USB Mass Storage driver...
[    3.000460] scsi4 : SCSI emulation for USB Mass Storage devices
[    3.000529] usb-storage: device found at 4
[    3.000531] usb-storage: waiting for device to settle before scanning
[    3.000540] usbcore: registered new interface driver usb-storage
[    3.000543] USB Mass Storage support registered.
[    3.224029] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    3.224173] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    3.232242] ata3.00: ATAPI: TSSTcorp DVD+/-RW TS-H653G, DW10, max UDMA/100
[    3.232260] ata3.00: applying bridge limits
[    3.232447] ata1.00: ATA-7: SAMSUNG HE160HJ, JF800-24, max UDMA7
[    3.232450] ata1.00: 312500000 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    3.240251] ata1.00: configured for UDMA/133
[    3.240346] scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HE160HJ  JF80 PQ: 0 ANSI: 5
[    3.240488] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    3.240524] sd 0:0:0:0: [sda] 312500000 512-byte logical blocks: (160 GB/149 GiB)
[    3.240571] sd 0:0:0:0: [sda] Write Protect is off
[    3.240574] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    3.240595] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.240726]  sda:
[    3.248167] ata3.00: configured for UDMA/100
[    3.248591]  sda1 sda2 < sda5 > sda3
[    3.275239] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.352022] usb 2-2: new full speed USB device using ohci_hcd and address 2
[    3.552023] ata2: SATA link down (SStatus 0 SControl 300)
[    3.553106] scsi 2:0:0:0: CD-ROM            TSSTcorp DVD+-RW TS-H653G DW10 PQ: 0 ANSI: 5
[    3.555614] sr0: scsi3-mmc drive: 125x/125x writer dvd-ram cd/rw xa/form2 cdda tray
[    3.555617] Uniform CD-ROM driver Revision: 3.20
[    3.555713] sr 2:0:0:0: Attached scsi CD-ROM sr0
[    3.555774] sr 2:0:0:0: Attached scsi generic sg1 type 5
[    3.561296] usb 2-2: configuration #1 chosen from 1 choice
[    3.864022] ata4: SATA link down (SStatus 0 SControl 300)
[    3.868017] usb 2-3: new low speed USB device using ohci_hcd and address 3
[    3.896842] [drm] radeon disabling kernel modesetting for known bad device.
[    3.897001] pci 0000:01:08.0: enabling device (0384 -> 0387)
[    3.897267] ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 18
[    3.897272]   alloc irq_desc for 18 on node -1
[    3.897274]   alloc kstat_irqs on node -1
[    3.897281] pci 0000:01:08.0: PCI INT A -> Link[LNK1] -> GSI 18 (level, low) -> IRQ 18
[    3.897405] [drm] Initialized radeon 1.32.0 20080528 for 0000:01:08.0 on minor 0
[    3.900464] usbcore: registered new interface driver hiddev
[    3.908361] input: C-Media USB Headphone Set   as /devices/pci0000:00/0000:00:02.0/usb2/2-2/2-2:1.3/input/input3
[    3.908445] generic-usb 0003:0D8C:000C.0001: input,hidraw0: USB HID v1.00 Device [C-Media USB Headphone Set  ] on usb-0000:00:02.0-2/input3
[    3.908477] usbcore: registered new interface driver usbhid
[    3.908480] usbhid: v2.6:USB HID core driver
[    3.916502] nouveau 0000:03:00.0: PCI INT A -> Link[LNK1] -> GSI 18 (level, low) -> IRQ 18
[    3.916508] nouveau 0000:03:00.0: setting latency timer to 64
[    3.918145] vga16fb: initializing
[    3.918149] vga16fb: mapped to 0xc00a0000
[    3.918199] fb0: VGA16 VGA frame buffer device
[    3.918711] [drm] nouveau 0000:03:00.0: Detected an NV40 generation card (0x04b300b1)
[    3.919068] [drm] nouveau 0000:03:00.0: Attempting to load BIOS image from PROM
[    4.082405] usb 2-3: configuration #1 chosen from 1 choice
[    4.092538] input: NOVATEK USB Keyboard as /devices/pci0000:00/0000:00:02.0/usb2/2-3/2-3:1.0/input/input4
[    4.092604] generic-usb 0003:0603:00F2.0002: input,hidraw1: USB HID v1.10 Keyboard [NOVATEK USB Keyboard] on usb-0000:00:02.0-3/input0
[    4.105387] input: NOVATEK USB Keyboard as /devices/pci0000:00/0000:00:02.0/usb2/2-3/2-3:1.1/input/input5
[    4.105474] generic-usb 0003:0603:00F2.0003: input,hiddev96,hidraw2: USB HID v1.10 Device [NOVATEK USB Keyboard] on usb-0000:00:02.0-3/input1
[    4.140670] [drm] nouveau 0000:03:00.0: ... appears to be valid
[    4.140674] [drm] nouveau 0000:03:00.0: BIT BIOS found
[    4.140676] [drm] nouveau 0000:03:00.0: Bios version 05.73.22.51
[    4.140679] [drm] nouveau 0000:03:00.0: TMDS table script pointers not stubbed
[    4.140682] [drm] nouveau 0000:03:00.0: BIT table 'd' not found
[    4.140685] [drm] nouveau 0000:03:00.0: Found Display Configuration Block version 3.0
[    4.140688] [drm] nouveau 0000:03:00.0: DCB connector table: VHER 0x30 5 10 2
[    4.140691] [drm] nouveau 0000:03:00.0:   0: 0x00001030: type 0x30 idx 0 tag 0x07
[    4.140694] [drm] nouveau 0000:03:00.0:   1: 0x00002130: type 0x30 idx 1 tag 0x08
[    4.140697] [drm] nouveau 0000:03:00.0:   2: 0x00000210: type 0x10 idx 2 tag 0xff
[    4.140699] [drm] nouveau 0000:03:00.0:   3: 0x00000211: type 0x11 idx 2 tag 0xff
[    4.140702] [drm] nouveau 0000:03:00.0:   4: 0x00000213: type 0x13 idx 2 tag 0xff
[    4.140705] [drm] nouveau 0000:03:00.0: Raw DCB entry 0: 01000300 00000028
[    4.140708] [drm] nouveau 0000:03:00.0: Raw DCB entry 1: 03000302 00000000
[    4.140710] [drm] nouveau 0000:03:00.0: Raw DCB entry 2: 04011310 00000028
[    4.140712] [drm] nouveau 0000:03:00.0: Raw DCB entry 3: 04011312 00000000
[    4.140715] [drm] nouveau 0000:03:00.0: Raw DCB entry 4: 020223f1 00c0c080
[    4.140722] [drm] nouveau 0000:03:00.0: Parsing VBIOS init table 0 at offset 0xCE4D
[    4.141056] [drm] nouveau 0000:03:00.0: Parsing VBIOS init table 1 at offset 0xD4F7
[    4.188536] [drm] nouveau 0000:03:00.0: Parsing VBIOS init table 2 at offset 0xDBFE
[    4.188558] [drm] nouveau 0000:03:00.0: Parsing VBIOS init table 3 at offset 0xDD82
[    4.212525] [drm] nouveau 0000:03:00.0: Parsing VBIOS init table 4 at offset 0xDEFA
[    4.245221] Console: switching to colour frame buffer device 80x30
[    4.269268] [TTM] Zone  kernel: Available graphics memory: 436888 kiB.
[    4.269271] [TTM] Zone highmem: Available graphics memory: 1030236 kiB.
[    4.269280] [drm] nouveau 0000:03:00.0: 128 MiB VRAM
[    4.272484] [drm] nouveau 0000:03:00.0: 64 MiB GART (aperture)
[    4.273914] [drm] nouveau 0000:03:00.0: Allocating FIFO number 0
[    4.278310] [drm] nouveau 0000:03:00.0: nouveau_channel_alloc: initialised FIFO 0
[    4.278319] [drm] nouveau 0000:03:00.0: Initial CRTC_OWNER is 0
[    4.278362] [drm] nouveau 0000:03:00.0: Detected a DVI-I connector
[    4.278415] [drm] nouveau 0000:03:00.0: Detected a DVI-I connector
[    4.278439] [drm] nouveau 0000:03:00.0: Detected a TV connector
[    4.280120] [drm] nouveau 0000:03:00.0: Setting dpms mode 3 on vga encoder (output 0)
[    4.280124] [drm] nouveau 0000:03:00.0: Setting dpms mode 3 on tmds encoder (output 1)
[    4.280127] [drm] nouveau 0000:03:00.0: Setting dpms mode 3 on vga encoder (output 2)
[    4.280130] [drm] nouveau 0000:03:00.0: Setting dpms mode 3 on tmds encoder (output 3)
[    4.280133] [drm] nouveau 0000:03:00.0: Setting dpms mode 3 on TV encoder (output 4)
[    4.408026] usb 2-7: new low speed USB device using ohci_hcd and address 4
[    4.464293] [drm] nouveau 0000:03:00.0: allocated 1920x1200 fb: 0x49000, bo f6aa6000
[    4.464394] fb1: nouveaufb frame buffer device
[    4.464396] registered panic notifier
[    4.464402] [drm] Initialized nouveau 0.0.15 20090420 for 0000:03:00.0 on minor 1
[    4.625511] usb 2-7: configuration #1 chosen from 1 choice
[    4.636611] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:02.0/usb2/2-7/2-7:1.0/input/input6
[    4.636692] logitech 0003:046D:C517.0004: input,hidraw3: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:02.0-7/input0
[    4.644436] xor: automatically using best checksumming function: pIII_sse
[    4.646407] logitech 0003:046D:C517.0005: fixing up Logitech keyboard report descriptor
[    4.647040] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:02.0/usb2/2-7/2-7:1.1/input/input7
[    4.647174] logitech 0003:046D:C517.0005: input,hiddev97,hidraw4: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:02.0-7/input1
[    4.661504]    pIII_sse  :  8622.000 MB/sec
[    4.661507] xor: using function: pIII_sse (8622.000 MB/sec)
[    4.664596] device-mapper: dm-raid45: initialized v0.2594b
[    4.771187] EXT4-fs (sda1): mounted filesystem with ordered data mode
[    4.878166] EXT4-fs (sda3): mounted filesystem with ordered data mode
[    6.029937] ISO 9660 Extensions: Microsoft Joliet Level 3
[    6.053745] ISO 9660 Extensions: RRIP_1991A
[    6.149210] aufs 2-standalone.tree-20091207
[    6.190956] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    6.352061] aufs test_add:243:exe[507]: uid/gid/perm //filesystem.squashfs 1000/1000/0755, 0/0/0755
[    8.000271] usb-storage: device scan complete
[   10.143502] scsi 4:0:0:0: Direct-Access     WDC WD32 00AAKS-00VYA0         PQ: 0 ANSI: 2
[   10.144007] sd 4:0:0:0: Attached scsi generic sg2 type 0
[   10.145356] sd 4:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[   10.148602] sd 4:0:0:0: [sdb] Write Protect is off
[   10.148605] sd 4:0:0:0: [sdb] Mode Sense: 38 00 00 00
[   10.148608] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[   10.152601] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[   10.152605]  sdb: sdb1
[   10.163612] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[   10.163616] sd 4:0:0:0: [sdb] Attached SCSI disk
[   37.356861] Adding 6032368k swap on /dev/sda5.  Priority:-1 extents:1 across:6032368k
[   37.991863] udev: starting version 151
[   40.477943] i2c i2c-2: nForce2 SMBus adapter at 0x2040
[   40.477965] i2c i2c-3: nForce2 SMBus adapter at 0x2000
[   40.544460] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[   41.033872] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   41.123169] dell-wmi: No known WMI GUID found
[   42.637631]   alloc irq_desc for 28 on node -1
[   42.637635]   alloc kstat_irqs on node -1
[   42.637647] tg3 0000:02:00.0: irq 28 for MSI/MSI-X
[   42.685278] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   44.318338] tg3: eth0: Link is up at 100 Mbps, full duplex.
[   44.318342] tg3: eth0: Flow control is on for TX and on for RX.
[   44.318549] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   44.700593] usbcore: registered new interface driver snd-usb-audio

オフライン

 

#18 2010-05-15 01:58:54

mithril02
メンバ
登録日: 2010-04-17

Re: 10.04LTS ライブCDの立ち上がり時間について

当方ubuntu10.04をCDに焼いてliveCDとして使ってみましたが、起動に13分もかかるようなことはありませんでした。
かかっても大体3～4分くらいです。(でも重いかと言われたらやはり重いレベルです。。。)
環境はCore2 Duo P8600@2.40GHz 2.40GHz,メモリ2.00GB
CDはFMVBIBLOMGC77D1でbraseroを使って焼きました。

オフライン

 

#19 2010-05-15 04:34:31

funatogawa
メンバ
From: 関東
登録日: 2009-02-01

Re: 10.04LTS ライブCDの立ち上がり時間について

こんばんは

CDへ焼くときのみのバグって事になるんでしょうか？　７００MBの生ディスク使ってます。論理的にはOKな筈なんでしょうけど。。。他でCDに焼いていらっしゃる方もいると思うんですが、問題なくたちあがってるんでしょうか？

ということですが、私はCDを使っています。Ubuntuでエラーを起こしたことはありません。ただし、CDブランドによってエラーが多めなのもあるようなので、経験上T？Kのものを使っています。それからCDエラーを起こすときはクリーニングをすることにしています。
　でも、いまだに作ったドライブと読み込みドライブが違うとエラーを起こすことがあります。なるべく同じドライブになるようにしてはいますが。

オフライン

 

#20 2010-05-15 12:02:47

hito
管理者
登録日: 2007-03-18

Re: 10.04LTS ライブCDの立ち上がり時間について

hiropack による投稿:

下に　/var/log/dmesg　張り付けます。　　CDの時に出ていたエラーがDVDの場合では出てません。　

って事は、CDへ焼くときのみのバグって事になるんでしょうか？　７００MBの生ディスク使ってます。論理的にはOKな筈なんでしょうけど。。。他でCDに焼いていらっしゃる方もいると思うんですが、問題なくたちあがってるんでしょうか？　とすれば私のマシン上でのドライブとライティングソフトの組み合わせのみで発生するという訳の分からない状況になってしまうんですが。

というあたりを確定させるには、


仮説としては、↓あたりがあったわけですが、以前のバージョンのUbuntuメディアなら起動できている、ということなのでハードウェア故障のセンは薄そうです。

・ハードウェア故障：　問題のドライブのCD-R読み取りモードが壊れている（DVD読み取りモードは動く）
・焼き込み失敗：　700MB付近へのoverburnが失敗してしまう何かに遭遇している
・読み取り失敗：　（overburnされた or CD-Rの ）メディアの読み込みに失敗する何かに遭遇している
・10.04だけの問題：　10.04だけ特異的に失敗する要素がある

追いかけるとより細かい問題に分岐しそうですが、個人的には以前のUbuntuを新たに焼いて、それでどうなるかを見てみたいところです。原因追及が大変そうなので、気にせず「DVD-Rに焼くなら大丈夫」という理解でブラックボックスにしてしまっても良い気はします。

オフライン

 

#21 2010-05-15 20:07:34

hiropack
メンバ
登録日: 2009-02-27

Re: 10.04LTS ライブCDの立ち上がり時間について

皆様、情報ありがとうございます。

今日多々テストしましたが、ますます分からなくなってきました。

知人のwindows xp を借り、ソニー製新品CRーR700MBに焼いたものを自身マシンで立ち上げた所、やはり当初のメディアエラーにより、13分近く立ち上がりに要しました。またこのCDでは、インストールと途中で選択可能なはずのUBUNTUをテスト使用するか、インストールするかの画面がでず、いきなり Live画面とかなリました。

また別のラップトップ8.04がインストールされているBraseroにてCDーRWへ書き込んだものでは4分弱と通常にブートしました。

知人のマシンを借りていて気づいたのですが、私のマシンの場合、ブート後しばらくしてから表示されるべく
　　　Ubuntu
　　　 . . . . .
が全てのケースにおいてされません。　ライブCD内には対応するドライバーがないのが理由と思われますが。

よって、　理由は　７００MB付近では上手く焼けないドライブと焼き付けソフトの組み合わせがあるのではないでしょうか。
加えて10.04の特異的な問題が私のマシンとの相性がよくないのでしょう。
何か根の深い問題っぽいのでこのままDVDにてインストールをして　9.10 と10.04 のデュアルブートでいきます。

でもちょっと気になりますね。

オフライン

 

#22 2010-05-15 21:48:14

gontomo
メンバ
From: 北海道
登録日: 2010-02-17

Re: 10.04LTS ライブCDの立ち上がり時間について

書き込みに使ったソフトでの品質問題というのは聞いたことないですね。
よくあるのは、メディアの品質、書込・読込ドライブの相性、書込ドライブとメディアの相性、読込・書込ドライブの故障。
とりあえず、正常に起動できる組み合わせがあるということは読込ドライブの故障はなさそうというところですね。

起動画面(Plymouth)が表示されない件ですが、KMSのトラブルを踏んでるんだと思います。
https://wiki.ubuntu.com/LucidLynx/ReleaseNotes/jaの「新しいカーネル・ビデオアーキテクチャでのバグの回避方法」(結構下の方)を確認してみてください。
個人的な印象ですが、ネットで見ていると、Intel, nvidia系で多いみたいです。

オフライン

 

#23 2010-05-15 22:16:34

hiropack
メンバ
登録日: 2009-02-27

Re: 10.04LTS ライブCDの立ち上がり時間について

ありがとうございます。　Playmouth は教えて頂いたところで調べてみます。自分もnvidia ですし。

書き込みソフトとデバイスの組み合わせと言った意味でした。良く調べて見ましたが、overburn できるソフトとできないものがあるようですね。（windows上で）

オフライン

 

#24 2010-05-17 20:58:00

suikan
新しいメンバ
登録日: 2010-01-02

Re: 10.04LTS ライブCDの立ち上がり時間について

hiropack による投稿:

表題の件、私のマシンで電源を入れてから使用できるようになるまで１３分もかかります。　9.10 では3分弱です。
CDがうまく焼けなかったかなと思い数枚焼いてみました。すべてに於いて時間かかってます。

私の手元でも同じ問題が起きます。プラットホームはIntelですが、DVDドライブがおなじ TS-H653Gです。症状としては、アクセス後、すぐに低速アクセスになるというものです。同じ環境でCDに焼いた古いUbuntuでは問題が起きないため、このドライブが影響を受けるような何らかの変更がCD/DVDのデバイスドライバに施されたのではないかと思っています。

10.04LTS発表直後に気づいたのですが、同様のレポートがあがっていなかったため、あきらめてUSBドライブからブートするようにしていました。

オフライン

 

#25 2010-05-18 11:39:53

hiropack
メンバ
登録日: 2009-02-27

Re: 10.04LTS ライブCDの立ち上がり時間について

suikanさん、

ドライブが影響を受けるようなドライバーを含めた変更とともに何か別な複合的要因にあるように見受けられます。
といいますのも知人のWinで焼いてもらったCDでも同様の問題が発生するからです。　
そのCDを別のラップトップにて起動させてみましが、立ち上がりはするものの途中でエラー発生と表示されますし。。。
エラー内容は不明。
　　

それとも　読み込みの際にこのドライブがCDのケースのみ影響を受けているのでしょうかね？？？

今回この情報をいただき感謝して折ります。　消去法でいけばビデオ回りの問題では無いんだろうなと予想できますので。
自分今度時間がある時、別ブランドのドライブを付けてテストしようと思っております。

10.04　まだまだ問題沢山ありそうですね。

オフライン

 

 

ページ: 1 2

Board footer

Powered by FluxBB