Ubuntu日本語フォーラム

TosaOTAK · 2009-01-19 21:49:10

ある日突然Xが起動しなくなり、CUIしか使えません。
環境は
Intel Pentium iii 866MHz
i686
512Mibyte RAM
NVIDIA GeForce2 MX
Ubuntu8.10
2.6.27-11-generic
です
Sambaが動くのでXorg.0.logをWinに飛ばして見ましたが、私にはお手上げです。
Googleで検索してみましたが、必要な情報が見つかりませんでした。
何か知恵を貸していただけないでしょうか

hir0 · 2009-01-20 01:39:32

ある日突然Xが起動しなくなり、CUIしか使えません。

突然、何があったか分れば良いのですが。

Googleで検索してみましたが、必要な情報が見つかりませんでした。
何か知恵を貸していただけないでしょうか

他の方の助けが来るまでに私の思い当たる（いろいろなパターン）事を書きます。
他の人がそれを見て解決策が分かるかも知れません。

$ startx
$ xinit gunome-session

$ runlevel　の結果はどうでしょうか。

NVIDIA GeForce2 MXと有りますが最近ドライバを変更、更新したことは？　ドライバをvesaにしてみます。
起動時grubのＯＳ選択画面で（無ければＥｓｃキーを）Ｅキーを押して編集モードにしてカーソルで２番目のKernel行に移り
もう一度Ｅキーを押す。
カーソルが点滅しているので１文字空白を入れてxforcevesaを追加、Enterキーを押してＢキーで起動させます。

$ sudo nano /etc/X11/xorg.conf の内容はどうでしょうか？

とりあえずのオマジナイ
$ sudo apt-get update
$ sudo apt-get upgrade

$ sudo sysv-rc-conf sysv-rc-confがインストールされているかどうか？

ライブＣＤではどうでしょうか？　ハードの面か、設定なのかの判断として。

思いつくのはこれぐらいです、すみません。
後は別のアプローチをアドバイスしてくれる方に期待を。

kiyoshi · 2009-01-20 07:12:07

※規約違反により追放されたユーザの投稿は、ログインユーザにのみ表示されます。

最後の編集者: kiyoshi (2009-01-20 12:13:00)

koisan1949 · 2009-01-20 08:04:49

TosaOTAKさん　横からすみません。マザーボードは何を使用されてますか。

それから、8.10の場合は私も遭遇したのですが、古いNVIDIA Geforceのカードを利用するとX画面に問題あります。
そのため、下記内容を決め打ちですがコマンド・モードで実行してください。参考になるかも。。。
　(的外れなら、ごめんなさいです)
カーネルとdisplay driverとの相性の様な気もします。
$ dmesg　で表示されるドライバーの部分をcopy & pastしてください。
　note: ズラズラと表示されるので、ハード回りが自動的にどう解釈されたか分かります。
$ uname -r　でカーネルを再確認してください。

カーネルのダウングレードを実施してください。その訳は、こちらを参照してください。私も識者に教えてもらいました。
http://forums.ubuntulinux.jp/viewtopic. … 282#p24282

ps. hir0さんの提示されたものに、アレンジしました。この方法を試されるのが先です。。。。
「起動時grubのＯＳ選択画面で（無ければＥｓｃキーを）押し、カーソルで３番目のKernel行に移りEnterキーを押す」
これで、カーネル2.6.27-9-generic　で起動しますので、以前の状態に復帰しませんか。。。

最後の編集者: koisan1949 (2009-01-20 08:59:17)

TosaOTAK · 2009-01-20 17:46:27

Xorg.0.logの内容です

X.Org X Server 1.5.2
Release Date: 10 October 2008
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.24-19-server i686 Ubuntu
Current Operating System: Linux fairy-desktop 2.6.27-11-generic #1 SMP Thu Jan 15 11:03:58 UTC 2009 i686
Build Date: 24 October 2008 08:00:16AM
xorg-server 2:1.5.2-2ubuntu3 ([email protected])
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Mon Jan 19 19:04:28 2009
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "Default Layout"
(**) |-->Screen "Default Screen" (0)
(**) | |-->Monitor "Configured Monitor"
(**) | |-->Device "Configured Video Device"
(==) Automatically adding devices
(==) Automatically enabling devices
(==) No FontPath specified. Using compiled-in default.
(WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
Entry deleted from font path.
(==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/100dpi/:unscaled,
/usr/share/fonts/X11/75dpi/:unscaled,
/usr/share/fonts/X11/Type1,
/usr/share/fonts/X11/100dpi,
/usr/share/fonts/X11/75dpi,
/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on HAL to provide the list of input devices.
If no devices become available, reconfigure HAL or disable AllowEmptyInput.
(II) Open ACPI successful (/var/run/acpid.socket)
(II) Loader magic: 0x81d9a40
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 4.1
X.Org XInput driver : 2.1
X.Org Server Extension : 1.1
X.Org Font Renderer : 0.6
(II) Loader running on linux
(--) using VT number 9

(--) PCI:*(0@1:0:0) nVidia Corporation NV11 [GeForce2 MX/MX 400] rev 161, Mem @ 0xd6000000/0, 0xd8000000/0, BIOS @ 0x????????/65536
(II) System resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) "extmod" will be loaded by default.
(II) "dbe" will be loaded by default.
(II) "glx" will be loaded. This was enabled by default and also specified in the config file.
(II) "freetype" will be loaded by default.
(II) "record" will be loaded by default.
(II) "dri" will be loaded by default.
(II) LoadModule: "glx"

(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 7.4.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 1.1
(**) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "v4l"

(II) Loading /usr/lib/xorg/modules/drivers//v4l_drv.so
(II) Module v4l: vendor="X.Org Foundation"
compiled for 1.5.0, module version = 0.1.1
ABI class: X.Org Video Driver, version 4.1
(II) LoadModule: "extmod"

(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"

(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "freetype"

(II) Loading /usr/lib/xorg/modules//fonts/libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 1.5.2, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.6
(II) Loading font FreeType
(II) LoadModule: "record"

(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension RECORD
(II) LoadModule: "dri"

(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 7.4.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension XFree86-DRI
(II) LoadModule: "nv"

(II) Loading /usr/lib/xorg/modules/drivers//nv_drv.so
(II) Module nv: vendor="X.Org Foundation"
compiled for 1.5.0, module version = 2.1.10
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 4.1
(II) v4l driver for Video4Linux
(II) NV: driver for NVIDIA chipsets: RIVA 128, RIVA TNT, RIVA TNT2,
Unknown TNT2, Vanta, RIVA TNT2 Ultra, RIVA TNT2 Model 64,
Aladdin TNT2, GeForce 256, GeForce DDR, Quadro, GeForce2 MX/MX 400,
GeForce2 MX 100/200, GeForce2 Go, Quadro2 MXR/EX/Go,
GeForce2 Integrated GPU, GeForce2 GTS, GeForce2 Ti, GeForce2 Ultra,
Quadro2 Pro, GeForce4 MX 460, GeForce4 MX 440, GeForce4 MX 420,
GeForce4 MX 440-SE, GeForce4 440 Go, GeForce4 420 Go,
GeForce4 420 Go 32M, GeForce4 460 Go, Quadro4 550 XGL,
GeForce4 440 Go 64M, Quadro NVS, Quadro4 500 GoGL,
GeForce4 410 Go 16M, GeForce4 MX 440 with AGP8X,
GeForce4 MX 440SE with AGP8X, GeForce4 MX 420 with AGP8X,
GeForce4 MX 4000, GeForce4 448 Go, GeForce4 488 Go, Quadro4 580 XGL,
Quadro4 NVS 280 SD, Quadro4 380 XGL, Quadro NVS 50 PCI,
GeForce4 448 Go, GeForce4 MX Integrated GPU, GeForce3,
GeForce3 Ti 200, GeForce3 Ti 500, Quadro DCC, GeForce4 Ti 4600,
GeForce4 Ti 4400, GeForce4 Ti 4200, Quadro4 900 XGL, Quadro4 750 XGL,
Quadro4 700 XGL, GeForce4 Ti 4800, GeForce4 Ti 4200 with AGP8X,
GeForce4 Ti 4800 SE, GeForce4 4200 Go, Quadro4 700 GoGL,
Quadro4 980 XGL, Quadro4 780 XGL, GeForce FX 5800 Ultra,
GeForce FX 5800, Quadro FX 2000, Quadro FX 1000,
GeForce FX 5600 Ultra, GeForce FX 5600, GeForce FX 5600XT,
GeForce FX Go5600, GeForce FX Go5650, Quadro FX Go700,
GeForce FX 5200, GeForce FX 5200 Ultra, GeForce FX 5200,
GeForce FX 5200LE, GeForce FX Go5200, GeForce FX Go5250,
GeForce FX 5500, GeForce FX 5100, GeForce FX Go5200 32M/64M,
Quadro NVS 55/280 PCI, Quadro FX 500/600 PCI,
GeForce FX Go53xx Series, GeForce FX Go5100, GeForce FX 5900 Ultra,
GeForce FX 5900, GeForce FX 5900XT, GeForce FX 5950 Ultra,
GeForce FX 5900ZT, Quadro FX 3000, Quadro FX 700,
GeForce FX 5700 Ultra, GeForce FX 5700, GeForce FX 5700LE,
GeForce FX 5700VE, GeForce FX Go5700, GeForce FX Go5700,
Quadro FX Go1000, Quadro FX 1100, GeForce 6800 Ultra, GeForce 6800,
GeForce 6800 LE, GeForce 6800 XE, GeForce 6800 XT, GeForce 6800 GT,
GeForce 6800 GT, GeForce 6800 GS, GeForce 6800 XT, Quadro FX 4000,
GeForce 6800 GS, GeForce 6800, GeForce 6800 LE, GeForce 6800 XT,
GeForce Go 6800, GeForce Go 6800 Ultra, Quadro FX Go1400,
Quadro FX 3450/4000 SDI, Quadro FX 1400, GeForce 6600 GT,
GeForce 6600, GeForce 6600 LE, GeForce 6600 VE, GeForce Go 6600,
GeForce 6610 XL, GeForce Go 6600 TE/6200 TE, GeForce 6700 XL,
GeForce Go 6600, GeForce Go 6600 GT, Quadro FX 550, Quadro FX 550,
Quadro FX 540, GeForce 6200, GeForce 6500,
GeForce 6200 TurboCache(TM), GeForce 6200SE TurboCache(TM),
GeForce 6200 LE, GeForce Go 6200, Quadro NVS 285, GeForce Go 6400,
GeForce Go 6200, GeForce Go 6400, GeForce 6250, GeForce 6800,
GeForce 6800 LE, GeForce 6800 GT, GeForce 6800 XT, GeForce 6200,
GeForce 6200 A-LE, GeForce 7800 GTX, GeForce 7800 GTX,
GeForce 7800 GT, GeForce 7800 GS, GeForce 7800 SLI, GeForce Go 7800,
GeForce Go 7800 GTX, Quadro FX 4500, GeForce 7300 LE,
GeForce 7300 SE, GeForce Go 7200, GeForce Go 7300, GeForce Go 7400,
GeForce Go 7400 GS, Quadro NVS 110M, Quadro NVS 120M, Quadro FX 350M,
GeForce 7500 LE, Quadro FX 350, GeForce 7300 GS, GeForce 7600 GT,
GeForce 7600 GS, GeForce 7300 GT, GeForce 7600 LE, GeForce 7300 GT,
GeForce Go 7700, GeForce Go 7600, GeForce Go 7600 GT,
Quadro NVS 300M, GeForce Go 7900 SE, Quadro FX 550M, Quadro FX 560,
GeForce 7900 GTX, GeForce 7900 GT, GeForce 7900 GS,
GeForce Go 7900 GS, GeForce Go 7900 GTX, Quadro FX 2500M,
Quadro FX 1500M, Quadro FX 5500, Quadro FX 3500, Quadro FX 1500,
Quadro FX 4500 X2, GeForce 6150, GeForce 6150 LE, GeForce 6100,
GeForce Go 6150, GeForce Go 6100, GeForce 8800 GTX, GeForce 8800 GTS,
GeForce 8800 Ultra, Quadro FX 5600, Quadro FX 4600, GeForce 8600 GTS,
GeForce 8600 GT, GeForce 8600 GT, GeForce 8400 GS, GeForce 9500M GS,
GeForce 8600M GT, GeForce 9650M GS, GeForce 8700M GT, Quadro FX 370,
Quadro NVS 320M, Quadro FX 570M, Quadro FX 1600M, Quadro FX 570,
Quadro FX 1700, GeForce 8400 SE, GeForce 8500 GT, GeForce 8400 GS,
GeForce 8300 GS, GeForce 8400 GS, GeForce 8600M GS, GeForce 8400M GT,
GeForce 8400M GS, GeForce 8400M G, Quadro NVS 140M, Quadro NVS 130M,
Quadro NVS 135M, Quadro FX 360M, GeForce 9300M G, Quadro NVS 290,
GeForce GTX 280, GeForce GTX 260, GeForce 8800 GTS 512,
GeForce 8800 GT, GeForce 9800 GX2, GeForce 8800 GS,
GeForce 8800M GTS, GeForce 8800M GTX, GeForce 8800 GS,
GeForce 9600 GSO, GeForce 8800 GT, GeForce 9800 GTX, Quadro FX 3700,
Quadro FX 3600M, GeForce 9600 GT, GeForce 9600M GT, GeForce 9600M GS,
GeForce 9600M GT, GeForce 9500M G, GeForce 8400 GS, GeForce 9300M GS,
GeForce 9200M GS, GeForce 9300M GS

Backtrace:
0: X(xf86SigHandler+0x79) [0x80c3009]
1: [0xb8057400]
2: X(initPciBusState+0x8a) [0x80d973a]
3: X(xf86AccessInit+0x1c) [0x80ba2dc]
4: X(InitOutput+0x660) [0x80aa990]
5: X(main+0x279) [0x8071b19]
6: /lib/tls/i686/cmov/libc.so.6(__libc_start_main+0xe5) [0xb7c47685]
7: X [0x8071101]
Saw signal 11. Server aborting.

hir0 · 2009-01-20 20:27:34

いや〜はずかしい。始めて見ました。　ログがあるんですね！
素人の戯言として聞いてください。初めにxorg.confのデフォルト設定を読み込みグラフィックドライバを読み込んでるみたいですが、
途中で一ヶ所、警告warningがでていてキリル文字cyrillicを適用せず、デフォルトの設定を読み込んだみたいです。
ですが、その後エラーや警告は無いと思います。

分からないのに口を出すなと言うのは無にしてもらって（スミマセン）
原因がXの設定の読み込み時、変更時のエラーだとログを解析出来る人が現れればいいのですが、原因を絞り込むためにも
もしお時間があれば、他の情報や操作の結果があれば良いと思います。

koisan1949 · 2009-01-20 20:38:44

私のPCで、現在は普通に問題なく画面表示されていますGeforce4におけるXorg.0.logを比較のため、参考に提示します。

コード:

X.Org X Server 1.5.2
Release Date: 10 October 2008
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.24-19-server i686 Ubuntu
Current Operating System: Linux Koike-Ubuntu 2.6.27-9-server #1 SMP Thu Nov 20 22:53:41 UTC 2008 i686
Build Date: 24 October 2008  08:00:16AM
xorg-server 2:1.5.2-2ubuntu3 ([email protected]) 
    Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Tue Jan 20 20:07:48 2009
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "Layout0"
(**) |-->Screen "Screen0" (0)
(**) |   |-->Monitor "Monitor0"
(**) |   |-->Device "Device0"
(**) |-->Input Device "Keyboard0"
(**) |-->Input Device "Mouse0"
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
    Entry deleted from font path.
(==) FontPath set to:
    /usr/share/fonts/X11/misc,
    /usr/share/fonts/X11/100dpi/:unscaled,
    /usr/share/fonts/X11/75dpi/:unscaled,
    /usr/share/fonts/X11/Type1,
    /usr/share/fonts/X11/100dpi,
    /usr/share/fonts/X11/75dpi,
    /var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Open ACPI successful (/var/run/acpid.socket)
(II) Loader magic: 0x81d9a40
(II) Module ABI versions:
    X.Org ANSI C Emulation: 0.4
    X.Org Video Driver: 4.1
    X.Org XInput driver : 2.1
    X.Org Server Extension : 1.1
    X.Org Font Renderer : 0.6
(II) Loader running on linux
(++) using VT number 7

(--) PCI:*(0@1:0:0) nVidia Corporation NV17 [GeForce4 MX 420] rev 163, Mem @ 0xdc000000/0, 0xd4000000/0, 0xd8000000/0, BIOS @ 0x????????/131072
(II) System resource ranges:
    [0] -1    0    0xffffffff - 0xffffffff (0x1) MX[b]
    [1] -1    0    0x000f0000 - 0x000fffff (0x10000) MX[b]
    [2] -1    0    0x000c0000 - 0x000effff (0x30000) MX[b]
    [3] -1    0    0x00000000 - 0x0009ffff (0xa0000) MX[b]
    [4] -1    0    0x0000ffff - 0x0000ffff (0x1) IX[b]
    [5] -1    0    0x00000000 - 0x00000000 (0x1) IX[b]
(II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
(II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
(II) "glx" will be loaded. This was enabled by default and also specified in the config file.
(II) "freetype" will be loaded. This was enabled by default and also specified in the config file.
(II) "record" will be loaded by default.
(II) "dri" will be loaded by default.
(II) LoadModule: "dbe"

(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
    compiled for 1.5.2, module version = 1.0.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 1.1
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "extmod"

(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
    compiled for 1.5.2, module version = 1.0.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 1.1
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "type1"

(WW) Warning, couldn't open module type1
(II) UnloadModule: "type1"
(EE) Failed to load module "type1" (module does not exist, 0)
(II) LoadModule: "freetype"

(II) Loading /usr/lib/xorg/modules//fonts/libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
    compiled for 1.5.2, module version = 2.1.0
    Module class: X.Org Font Renderer
    ABI class: X.Org Font Renderer, version 0.6
(II) Loading font FreeType
(II) LoadModule: "glx"

(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="NVIDIA Corporation"
    compiled for 4.0.2, module version = 1.0.0
    Module class: X.Org Server Extension
(II) NVIDIA GLX Module  96.43.09  Mon Oct 27 14:37:08 PST 2008
(II) Loading extension GLX
(II) LoadModule: "record"

(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
    compiled for 1.5.2, module version = 1.13.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 1.1
(II) Loading extension RECORD
(II) LoadModule: "dri"

(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
    compiled for 1.5.2, module version = 1.0.0
    ABI class: X.Org Server Extension, version 1.1
(II) Loading extension XFree86-DRI
(II) LoadModule: "nvidia"

(II) Loading /usr/lib/xorg/modules/drivers//nvidia_drv.so
(II) Module nvidia: vendor="NVIDIA Corporation"
    compiled for 4.0.2, module version = 1.0.0
    Module class: X.Org Video Driver
(II) LoadModule: "kbd"

(II) Loading /usr/lib/xorg/modules/input//kbd_drv.so
(II) Module kbd: vendor="X.Org Foundation"
    compiled for 1.4.99.905, module version = 1.3.1
    Module class: X.Org XInput Driver
    ABI class: X.Org XInput driver, version 2.1
(II) LoadModule: "mouse"

(II) Loading /usr/lib/xorg/modules/input//mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
    compiled for 1.4.99.905, module version = 1.3.0
    Module class: X.Org XInput Driver
    ABI class: X.Org XInput driver, version 2.1
(II) NVIDIA dlloader X Driver  96.43.09  Mon Oct 27 14:25:40 PST 2008
(II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
(II) Primary Device is: PCI 01@00:00:0
(II) Loading sub module "fb"
(II) LoadModule: "fb"

(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
    compiled for 1.5.2, module version = 1.0.0
    ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"

(II) Loading /usr/lib/xorg/modules//libxaa.so
(II) Module xaa: vendor="X.Org Foundation"
    compiled for 1.5.2, module version = 1.2.0
    ABI class: X.Org Video Driver, version 4.1
(II) resource ranges after probing:
    [0] -1    0    0xffffffff - 0xffffffff (0x1) MX[b]
    [1] -1    0    0x000f0000 - 0x000fffff (0x10000) MX[b]
    [2] -1    0    0x000c0000 - 0x000effff (0x30000) MX[b]
    [3] -1    0    0x00000000 - 0x0009ffff (0xa0000) MX[b]
    [4] -1    0    0x0000ffff - 0x0000ffff (0x1) IX[b]
    [5] -1    0    0x00000000 - 0x00000000 (0x1) IX[b]
(**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32
(==) NVIDIA(0): RGB weight 888
(==) NVIDIA(0): Default visual is TrueColor
(==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
(**) NVIDIA(0): Enabling RENDER acceleration
(II) NVIDIA(0): Support for GLX with the Damage and Composite X extensions is
(II) NVIDIA(0):     enabled.
(WW) NVIDIA(GPU-0): The EDID read for display device CRT-0 is invalid
(II) NVIDIA(0): NVIDIA GPU GeForce4 MX 420 at PCI:1:0:0 (GPU-0)
(--) NVIDIA(0): Memory: 65536 kBytes
(--) NVIDIA(0): VideoBIOS: 04.17.00.45.af
(II) NVIDIA(0): Detected AGP rate: 4X
(--) NVIDIA(0): Interlaced video modes are supported on this GPU
(--) NVIDIA(0): Connected display device(s) on GeForce4 MX 420 at PCI:1:0:0:
(--) NVIDIA(0):     CRT-0
(--) NVIDIA(0): CRT-0: 350.0 MHz maximum pixel clock
(II) NVIDIA(0): Assigned Display Device: CRT-0
(II) NVIDIA(0): Validated modes:
(II) NVIDIA(0):     "1280x1024"
(II) NVIDIA(0):     "1024x768"
(II) NVIDIA(0):     "800x600"
(II) NVIDIA(0):     "640x480"
(II) NVIDIA(0): Virtual screen size determined to be 1280 x 1024
(WW) NVIDIA(0): Unable to get display device CRT-0's EDID; cannot compute DPI
(WW) NVIDIA(0):     from CRT-0's EDID.
(==) NVIDIA(0): DPI set to (75, 75); computed from built-in default
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC?  No, I don't.
(II) resource ranges after preInit:
    [0] -1    0    0xffffffff - 0xffffffff (0x1) MX[b]
    [1] -1    0    0x000f0000 - 0x000fffff (0x10000) MX[b]
    [2] -1    0    0x000c0000 - 0x000effff (0x30000) MX[b]
    [3] -1    0    0x00000000 - 0x0009ffff (0xa0000) MX[b]
    [4] -1    0    0x0000ffff - 0x0000ffff (0x1) IX[b]
    [5] -1    0    0x00000000 - 0x00000000 (0x1) IX[b]
(II) NVIDIA(0): Initialized GART.
(II) NVIDIA(0): Setting mode "1280x1024"
(II) Loading extension NV-GLX
(II) NVIDIA(0): NVIDIA 3D Acceleration Architecture Initialized
(II) NVIDIA(0): Using the NVIDIA 2D acceleration architecture
(==) NVIDIA(0): Backing store disabled
(==) NVIDIA(0): Silken mouse enabled
(**) Option "dpms"
(**) NVIDIA(0): DPMS enabled
(II) Loading extension NV-CONTROL
(==) RandR enabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(II) Initializing extension GLX
(**) Option "CoreKeyboard"
(**) Keyboard0: always reports core events
(**) Option "Protocol" "standard"
(**) Keyboard0: Protocol: standard
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xorg"
(**) Keyboard0: XkbRules: "xorg"
(**) Option "XkbModel" "pc105"
(**) Keyboard0: XkbModel: "pc105"
(**) Option "XkbLayout" "us"
(**) Keyboard0: XkbLayout: "us"
(**) Option "CustomKeycodes" "off"
(**) Keyboard0: CustomKeycodes disabled
(**) Option "Protocol" "auto"
(**) Option "Device" "/dev/psaux"
(II) Mouse0: Setting mouse protocol to "ExplorerPS/2"
(**) Mouse0: Device: "/dev/psaux"
(**) Mouse0: Protocol: "auto"
(**) Option "CorePointer"
(**) Mouse0: always reports core events
(**) Option "Device" "/dev/psaux"
(**) Option "Emulate3Buttons" "no"
(**) Option "ZAxisMapping" "4 5"
(**) Mouse0: ZAxisMapping: buttons 4 and 5
(**) Mouse0: Buttons: 9
(**) Mouse0: Sensitivity: 1
(II) evaluating device (Keyboard0)
(II) XINPUT: Adding extended input device "Keyboard0" (type: KEYBOARD)
(II) evaluating device (Mouse0)
(II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE)
(II) Mouse0: Setting mouse protocol to "ExplorerPS/2"
(II) Mouse0: ps2EnableDataReporting: succeeded
(II) config/hal: Adding input device Macintosh mouse button emulation
(II) LoadModule: "evdev"

(II) Loading /usr/lib/xorg/modules/input//evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
    compiled for 1.5.2, module version = 2.0.99
    Module class: X.Org XInput Driver
    ABI class: X.Org XInput driver, version 2.1
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Configuring as mouse
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) config/hal: Adding input device ImExPS/2 Logitech Explorer Mouse
(**) ImExPS/2 Logitech Explorer Mouse: always reports core events
(**) ImExPS/2 Logitech Explorer Mouse: Device: "/dev/input/event5"
(II) ImExPS/2 Logitech Explorer Mouse: Found x and y relative axes
(II) ImExPS/2 Logitech Explorer Mouse: Found 5 mouse buttons
(II) ImExPS/2 Logitech Explorer Mouse: Configuring as mouse
(II) XINPUT: Adding extended input device "ImExPS/2 Logitech Explorer Mouse" (type: MOUSE)
(**) ImExPS/2 Logitech Explorer Mouse: YAxisMapping: buttons 4 and 5
(**) ImExPS/2 Logitech Explorer Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event1"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) AT Translated Set 2 keyboard: xkb_rules: "evdev"
(**) Option "xkb_model" "jp106"
(**) AT Translated Set 2 keyboard: xkb_model: "jp106"
(**) Option "xkb_layout" "jp,jp"
(**) AT Translated Set 2 keyboard: xkb_layout: "jp,jp"
(**) Option "xkb_variant" "106,kana"
(**) AT Translated Set 2 keyboard: xkb_variant: "106,kana"
(**) Option "xkb_options" "grp:alt_shift_toggle,grp_led:scroll"
(**) AT Translated Set 2 keyboard: xkb_options: "grp:alt_shift_toggle,grp_led:scroll"
AUDIT: Tue Jan 20 20:07:59 2009: 5122 X: client 4 rejected from local host ( uid=0 gid=0 pid=5421 )
AUDIT: Tue Jan 20 20:08:17 2009: 5122 X: client 4 rejected from local host ( uid=1000 gid=1000 pid=5427 )
AUDIT: Tue Jan 20 20:08:17 2009: 5122 X: client 4 rejected from local host ( uid=1000 gid=1000 pid=5428 )
AUDIT: Tue Jan 20 20:08:17 2009: 5122 X: client 4 rejected from local host ( uid=1000 gid=1000 pid=5429 )
(II) NVIDIA(0): Setting mode "1152x864_60"

カーネルを2.6.27-9にダウングレードすれば直ると思います。
ディスプレイ・ドライバーが開発途上の2.6.27-11にマッチングしてないのが原因と考えられます。

他の回避策としては、NVIDIAからmodule作成用のシェル・プログラクムをダウンロードして、実行します。
カーネル・ソース2.6.27-11に合ったモジュールを生成して入れ替えてくれます。

最後の編集者: koisan1949 (2009-01-21 12:24:58)

hir0 · 2009-01-20 22:19:04

Current Operating System: Linux fairy-desktop 2.6.27-11-generic

とりあえず、現時点で、koisan19492さんと同じ考えに行き着きました。

カーネルを2.6.27-9にダウングレードすれば直ると思います。

他の回避策としては、NVIDIAからmodule作成用のシェル・プログラクムをダウンロードして、実行します。
カーネル・ソース2.6.27-11に合ったモジュールを生成して入れ替えてくれます。

あと GeForce2MXのドライバについて参考になりそうなページです。
http://wikiwiki.jp/pico/?Kubuntu_Linux%2FGeForce2%20MX%A4%C7NVIDIA%A5%D7%A5%ED%A5%D7%A5%E9%A5%A4%A5%A8%A5%BF%A5%EA%A5%C9%A5%E9%A5%A4%A5%D0%A4%F2%BB%C8%CD%D1%A4%B9%A4%EB
＃４も合わせて検討してみて下さい。
http://forums.ubuntulinux.jp/viewtopic. … 282#p24282

TosaOTAK · 2009-01-21 20:52:23

一応2.6.27-8（2.6.27-9無いので）で起動してみましたが、
同じでした。他のカーネルも試しましたが変わりませんでした
一応dmesgの出力です

コード:

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.27-11-generic (buildd@palmer) (gcc version 4.3.2 (Ubuntu 4.3.2-1ubuntu11) ) #1 SMP Thu Jan 15 11:03:58 UTC 2009 (Ubuntu 2.6.27-11.24-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000001fffc000 (usable)
[    0.000000]  BIOS-e820: 000000001fffc000 - 000000001ffff000 (ACPI data)
[    0.000000]  BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[    0.000000] DMI 2.3 present.
[    0.000000] last_pfn = 0x1fffc max_arch_pfn = 0x100000
[    0.000000] kernel direct mapping tables up to 1fffc000 @ 7000-d000
[    0.000000] RAMDISK: 1f7d3000 - 1ffeb9e1
[    0.000000] ACPI: RSDP 000F5B30, 0014 (r0 ASUS  )
[    0.000000] ACPI: RSDT 1FFFC000, 002C (r1 ASUS   CUSL-LX  30303031 MSFT 31313031)
[    0.000000] ACPI: FACP 1FFFC080, 0074 (r1 ASUS   CUSL-LX  30303031 MSFT 31313031)
[    0.000000] ACPI: DSDT 1FFFC100, 2CDD (r1   ASUS CUSL-LX      1000 MSFT  100000B)
[    0.000000] ACPI: FACS 1FFFF000, 0040
[    0.000000] ACPI: BOOT 1FFFC040, 0028 (r1 ASUS   CUSL-LX  30303031 MSFT 31313031)
[    0.000000] ACPI: DMI detected: Sony
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 511MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 1fffc000
[    0.000000]   low ram: 00000000 - 1fffc000
[    0.000000]   bootmap 00002000 - 00006000
[    0.000000] (9 early reservations) ==> bootmem [0000000000 - 001fffc000]
[    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
[    0.000000]   #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
[    0.000000]   #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
[    0.000000]   #3 [0000100000 - 00005c29e0]    TEXT DATA BSS ==> [0000100000 - 00005c29e0]
[    0.000000]   #4 [001f7d3000 - 001ffeb9e1]          RAMDISK ==> [001f7d3000 - 001ffeb9e1]
[    0.000000]   #5 [00005c3000 - 00005c6000]    INIT_PG_TABLE ==> [00005c3000 - 00005c6000]
[    0.000000]   #6 [000009fc00 - 0000100000]    BIOS reserved ==> [000009fc00 - 0000100000]
[    0.000000]   #7 [0000007000 - 0000009000]          PGTABLE ==> [0000007000 - 0000009000]
[    0.000000]   #8 [0000002000 - 0000006000]          BOOTMAP ==> [0000002000 - 0000006000]
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000000 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x0001fffc
[    0.000000]   HighMem  0x0001fffc -> 0x0001fffc
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[2] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x0001fffc
[    0.000000] On node 0 totalpages: 130971
[    0.000000] free_area_init_node: node 0, pgdat c048c680, node_mem_map c1000000
[    0.000000]   DMA zone: 3963 pages, LIFO batch:0
[    0.000000]   Normal zone: 125856 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0xe408
[    0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[    0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[    0.000000] mapped APIC to ffffb000 (01482000)
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[    0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:dfff0000)
[    0.000000] PERCPU: Allocating 41628 bytes of per cpu data
[    0.000000] NR_CPUS: 64, nr_cpu_ids: 1, nr_node_ids 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 129819
[    0.000000] Kernel command line: root=UUID=c37edaac-b301-442f-b31c-d380289566de ro splash vga=794
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[    0.000000] TSC: PIT calibration confirmed by PMTIMER.
[    0.000000] TSC: using PMTIMER calibration value
[    0.000000] Detected 868.631 MHz processor.
[    0.004000] Console: colour dummy device 80x25
[    0.004000] console [tty0] enabled
[    0.004000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.004000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.004000] Memory: 505404k/524272k available (2576k kernel code, 18280k reserved, 1165k data, 424k init, 0k highmem)
[    0.004000] virtual kernel memory layout:
[    0.004000]     fixmap  : 0xffc77000 - 0xfffff000   (3616 kB)
[    0.004000]     pkmap   : 0xff400000 - 0xff800000   (4096 kB)
[    0.004000]     vmalloc : 0xe0800000 - 0xff3fe000   ( 491 MB)
[    0.004000]     lowmem  : 0xc0000000 - 0xdfffc000   ( 511 MB)
[    0.004000]       .init : 0xc04ad000 - 0xc0517000   ( 424 kB)
[    0.004000]       .data : 0xc03840da - 0xc04a7680   (1165 kB)
[    0.004000]       .text : 0xc0100000 - 0xc03840da   (2576 kB)
[    0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[    0.004000] SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.004018] Calibrating delay loop (skipped), value calculated using timer frequency.. 1737.26 BogoMIPS (lpj=3474524)
[    0.004078] Security Framework initialized
[    0.004102] SELinux:  Disabled at boot.
[    0.004163] AppArmor: AppArmor initialized
[    0.004191] Mount-cache hash table entries: 512
[    0.004594] Initializing cgroup subsys ns
[    0.004613] Initializing cgroup subsys cpuacct
[    0.004627] Initializing cgroup subsys memory
[    0.004669] CPU: L1 I cache: 16K, L1 D cache: 16K
[    0.004684] CPU: L2 cache: 256K
[    0.004697] CPU serial number disabled.
[    0.004734] Checking 'hlt' instruction... OK.
[    0.020741] SMP alternatives: switching to UP code
[    0.028050] Freeing SMP alternatives: 11k freed
[    0.028081] ACPI: Core revision 20080609
[    0.033027] ACPI: Checking initramfs for custom DSDT
[    0.847712] ACPI: setting ELCR to 0200 (from 0000)
[    0.848013] weird, boot CPU (#0) not listedby the BIOS.
[    0.848039] SMP motherboard not detected.
[    0.848053] Local APIC not detected. Using dummy APIC emulation.
[    0.848066] SMP disabled
[    0.848257] Brought up 1 CPUs
[    0.848270] Total of 1 processors activated (1737.26 BogoMIPS).
[    0.848307] CPU0 attaching NULL sched-domain.
[    0.848959] net_namespace: 840 bytes
[    0.848996] Booting paravirtualized kernel on bare hardware
[    0.849612] Time: 20:32:46  Date: 01/21/09
[    0.849701] NET: Registered protocol family 16
[    0.850707] EISA bus registered
[    0.850776] ACPI: bus type pci registered
[    0.852281] PCI: PCI BIOS revision 2.10 entry at 0xf0900, last bus=2
[    0.852306] PCI: Using configuration type 1 for base access
[    0.856526] ACPI: EC: Look up EC in DSDT
[    0.868781] ACPI: Interpreter enabled
[    0.868818] ACPI: (supports S0 S1 S4 S5)
[    0.868870] ACPI: Using PIC for interrupt routing
[    0.884157] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.884380] PCI: 0000:00:00.0 reg 10 32bit mmio: [e4000000, e7ffffff]
[    0.884591] pci 0000:00:1f.0: quirk: region e400-e47f claimed by ICH4 ACPI/GPIO/TCO
[    0.884614] pci 0000:00:1f.0: quirk: region ec00-ec3f claimed by ICH4 GPIO
[    0.884674] PCI: 0000:00:1f.1 reg 20 io port: [b800, b80f]
[    0.884749] PCI: 0000:00:1f.2 reg 20 io port: [b400, b41f]
[    0.884818] PCI: 0000:00:1f.3 reg 20 io port: [e800, e80f]
[    0.884865] PCI: 0000:00:1f.5 reg 10 io port: [e000, e0ff]
[    0.884878] PCI: 0000:00:1f.5 reg 14 io port: [e100, e13f]
[    0.884965] PCI: 0000:01:00.0 reg 10 32bit mmio: [d6000000, d6ffffff]
[    0.884977] PCI: 0000:01:00.0 reg 14 32bit mmio: [d8000000, dfffffff]
[    0.885006] PCI: 0000:01:00.0 reg 30 32bit mmio: [d7ff0000, d7ffffff]
[    0.885071] PCI: bridge 0000:00:01.0 32bit mmio: [d6000000, d7efffff]
[    0.885080] PCI: bridge 0000:00:01.0 32bit mmio pref: [d7f00000, e3ffffff]
[    0.885142] PCI: 0000:02:0a.0 reg 10 32bit mmio: [d5800000, d5800fff]
[    0.885193] pci 0000:02:0a.0: supports D1
[    0.885199] pci 0000:02:0a.0: supports D2
[    0.885205] pci 0000:02:0a.0: PME# supported from D0 D1 D2 D3hot
[    0.885222] pci 0000:02:0a.0: PME# disabled
[    0.885265] PCI: 0000:02:0a.1 reg 10 32bit mmio: [d5000000, d5000fff]
[    0.885317] pci 0000:02:0a.1: supports D1
[    0.885322] pci 0000:02:0a.1: supports D2
[    0.885328] pci 0000:02:0a.1: PME# supported from D0 D1 D2 D3hot
[    0.885344] pci 0000:02:0a.1: PME# disabled
[    0.885386] PCI: 0000:02:0a.2 reg 10 32bit mmio: [d4800000, d48000ff]
[    0.885438] pci 0000:02:0a.2: supports D1
[    0.885443] pci 0000:02:0a.2: supports D2
[    0.885449] pci 0000:02:0a.2: PME# supported from D0 D1 D2 D3hot
[    0.885464] pci 0000:02:0a.2: PME# disabled
[    0.885514] PCI: 0000:02:0b.0 reg 10 32bit mmio: [0, fff]
[    0.885534] pci 0000:02:0b.0: supports D1
[    0.885539] pci 0000:02:0b.0: supports D2
[    0.885545] pci 0000:02:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.885562] pci 0000:02:0b.0: PME# disabled
[    0.885608] PCI: 0000:02:0b.1 reg 10 32bit mmio: [0, fff]
[    0.885629] pci 0000:02:0b.1: supports D1
[    0.885634] pci 0000:02:0b.1: supports D2
[    0.885640] pci 0000:02:0b.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.885657] pci 0000:02:0b.1: PME# disabled
[    0.885710] PCI: 0000:02:0d.0 reg 10 io port: [d800, d8ff]
[    0.885723] PCI: 0000:02:0d.0 reg 14 32bit mmio: [d4000000, d40000ff]
[    0.885770] pci 0000:02:0d.0: supports D1
[    0.885775] pci 0000:02:0d.0: supports D2
[    0.885781] pci 0000:02:0d.0: PME# supported from D1 D2 D3hot D3cold
[    0.885797] pci 0000:02:0d.0: PME# disabled
[    0.885842] PCI: 0000:02:0e.0 reg 10 32bit mmio: [d3800000, d38007ff]
[    0.885856] PCI: 0000:02:0e.0 reg 14 32bit mmio: [d3000000, d3003fff]
[    0.885906] pci 0000:02:0e.0: PME# supported from D3hot
[    0.885921] pci 0000:02:0e.0: PME# disabled
[    0.885956] pci 0000:00:1e.0: transparent bridge
[    0.885971] PCI: bridge 0000:00:1e.0 io port: [d000, dfff]
[    0.885981] PCI: bridge 0000:00:1e.0 32bit mmio: [d3000000, d5ffffff]
[    0.886040] bus 00 -> node 0
[    0.886062] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.886476] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[    0.886718] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT]
[    0.893089] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.893389] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.893663] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.893937] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.894417] Linux Plug and Play Support v0.97 (c) Adam Belay
[    0.894549] pnp: PnP ACPI init
[    0.894585] ACPI: bus type pnp registered
[    0.904752] pnp: PnP ACPI: found 15 devices
[    0.904782] ACPI: ACPI bus type pnp unregistered
[    0.904801] PnPBIOS: Disabled by ACPI PNP
[    0.905960] PCI: Using ACPI for IRQ routing
[    0.906293] NET: Registered protocol family 8
[    0.906293] NET: Registered protocol family 20
[    0.906293] NetLabel: Initializing
[    0.906293] NetLabel:  domain hash size = 128
[    0.906293] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.906293] NetLabel:  unlabeled traffic allowed by default
[    0.906293] tracer: 772 pages allocated for 65536 entries of 48 bytes
[    0.906293]    actual entries 65620
[    0.906293] AppArmor: AppArmor Filesystem Enabled
[    0.908097] ACPI: RTC can wake from S4
[    0.908296] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[    0.908319] system 00:00: iomem range 0xf0000-0xfffff could not be reserved
[    0.908336] system 00:00: iomem range 0x100000-0x1fffffff could not be reserved
[    0.908355] system 00:00: iomem range 0xffb80000-0xffbfffff has been reserved
[    0.908372] system 00:00: iomem range 0xfff80000-0xffffffff could not be reserved
[    0.908409] system 00:02: ioport range 0x3f0-0x3f1 has been reserved
[    0.908426] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[    0.908455] system 00:03: ioport range 0xe400-0xe47f has been reserved
[    0.908472] system 00:03: ioport range 0xec00-0xec3f has been reserved
[    0.908488] system 00:03: ioport range 0x290-0x297 has been reserved
[    0.944978] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[    0.945006] pci 0000:00:01.0:   IO window: disabled
[    0.945024] pci 0000:00:01.0:   MEM window: 0xd6000000-0xd7efffff
[    0.945041] pci 0000:00:01.0:   PREFETCH window: 0x000000d7f00000-0x000000e3ffffff
[    0.945084] pci 0000:02:0b.0: CardBus bridge, secondary bus 0000:03
[    0.945098] pci 0000:02:0b.0:   IO window: 0x00d000-0x00d0ff
[    0.945114] pci 0000:02:0b.0:   IO window: 0x00d400-0x00d4ff
[    0.945130] pci 0000:02:0b.0:   PREFETCH window: 0x30000000-0x33ffffff
[    0.945147] pci 0000:02:0b.0:   MEM window: 0x38000000-0x3bffffff
[    0.945164] pci 0000:02:0b.1: CardBus bridge, secondary bus 0000:07
[    0.945178] pci 0000:02:0b.1:   IO window: 0x00dc00-0x00dcff
[    0.945194] pci 0000:02:0b.1:   IO window: 0x001000-0x0010ff
[    0.945210] pci 0000:02:0b.1:   PREFETCH window: 0x34000000-0x37ffffff
[    0.945226] pci 0000:02:0b.1:   MEM window: 0x3c000000-0x3fffffff
[    0.945243] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
[    0.945258] pci 0000:00:1e.0:   IO window: 0xd000-0xdfff
[    0.945275] pci 0000:00:1e.0:   MEM window: 0xd3000000-0xd5ffffff
[    0.945292] pci 0000:00:1e.0:   PREFETCH window: 0x00000030000000-0x00000037ffffff
[    0.945332] pci 0000:00:01.0: setting latency timer to 64
[    0.945346] pci 0000:00:1e.0: setting latency timer to 64
[    0.945361] pci 0000:02:0b.0: enabling device (0005 -> 0007)
[    0.946440] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[    0.946457] PCI: setting IRQ 11 as level-triggered
[    0.946468] pci 0000:02:0b.0: PCI INT A -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
[    0.946490] pci 0000:02:0b.0: setting latency timer to 64
[    0.946505] pci 0000:02:0b.1: enabling device (0005 -> 0007)
[    0.947432] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[    0.947450] pci 0000:02:0b.1: PCI INT B -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[    0.947471] pci 0000:02:0b.1: setting latency timer to 64
[    0.947482] bus: 00 index 0 io port: [0, ffff]
[    0.947494] bus: 00 index 1 mmio: [0, ffffffff]
[    0.947506] bus: 01 index 0 mmio: [0, 0]
[    0.947517] bus: 01 index 1 mmio: [d6000000, d7efffff]
[    0.947530] bus: 01 index 2 mmio: [d7f00000, e3ffffff]
[    0.947542] bus: 01 index 3 mmio: [0, 0]
[    0.947554] bus: 02 index 0 io port: [d000, dfff]
[    0.947566] bus: 02 index 1 mmio: [d3000000, d5ffffff]
[    0.947578] bus: 02 index 2 mmio: [30000000, 37ffffff]
[    0.947591] bus: 02 index 3 io port: [0, ffff]
[    0.947603] bus: 02 index 4 mmio: [0, ffffffff]
[    0.947615] bus: 03 index 0 io port: [d000, d0ff]
[    0.947627] bus: 03 index 1 io port: [d400, d4ff]
[    0.947639] bus: 03 index 2 mmio: [30000000, 33ffffff]
[    0.947652] bus: 03 index 3 mmio: [38000000, 3bffffff]
[    0.947665] bus: 07 index 0 io port: [dc00, dcff]
[    0.947677] bus: 07 index 1 io port: [1000, 10ff]
[    0.947689] bus: 07 index 2 mmio: [34000000, 37ffffff]
[    0.947702] bus: 07 index 3 mmio: [3c000000, 3fffffff]
[    0.947741] NET: Registered protocol family 2
[    0.948217] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.948938] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.949296] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[    0.949715] TCP: Hash tables configured (established 16384 bind 16384)
[    0.949740] TCP reno registered
[    0.950144] NET: Registered protocol family 1
[    0.950543] checking if image is initramfs...<7>Switched to high resolution mode on CPU 0
[    1.764569]  it is
[    2.779727] Freeing initrd memory: 8290k freed
[    2.780406] Simple Boot Flag at 0x3a set to 0x1
[    2.781697] audit: initializing netlink socket (disabled)
[    2.781758] type=2000 audit(1232569967.780:1): initialized
[    2.796749] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    2.804609] VFS: Disk quotas dquot_6.5.1
[    2.804979] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    2.805877] msgmni has been set to 1003
[    2.806397] io scheduler noop registered
[    2.806415] io scheduler anticipatory registered
[    2.806427] io scheduler deadline registered
[    2.806490] io scheduler cfq registered (default)
[    2.806586] pci 0000:01:00.0: Boot video device
[    2.807617] isapnp: Scanning for PnP cards...
[    3.161548] isapnp: No Plug & Play device found
[    3.314927] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[    3.315185] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    3.317801] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    3.323548] brd: module loaded
[    3.323816] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[    3.324296] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    3.326648] serio: i8042 KBD port at 0x60,0x64 irq 1
[    3.326679] serio: i8042 AUX port at 0x60,0x64 irq 12
[    3.328106] mice: PS/2 mouse device common for all mice
[    3.328618] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[    3.328667] rtc0: alarms up to one month
[    3.329051] EISA: Probing bus 0 at eisa.0
[    3.329077] Cannot allocate resource for EISA slot 1
[    3.329121] EISA: Detected 0 cards.
[    3.329135] cpuidle: using governor ladder
[    3.329147] cpuidle: using governor menu
[    3.330832] TCP cubic registered
[    3.330942] Using IPI No-Shortcut mode
[    3.331759] registered taskstats version 1
[    3.332155]   Magic number: 9:147:549
[    3.332436] pci_link PNP0C0F:00: hash matches
[    3.332490] rtc_cmos 00:05: setting system clock to 2009-01-21 20:32:48 UTC (1232569968)
[    3.332510] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    3.332524] EDD information not available.
[    3.333870] Freeing unused kernel memory: 424k freed
[    3.334061] Write protecting the kernel text: 2580k
[    3.334163] Write protecting the kernel read-only data: 940k
[    3.349315] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[    3.557418] vesafb: framebuffer at 0xd8000000, mapped to 0xe0880000, using 5120k, total 16384k
[    3.557456] vesafb: mode is 1280x1024x16, linelength=2560, pages=1
[    3.557471] vesafb: protected mode interface info at c000:0eb9
[    3.557485] vesafb: pmi: set display start = c00c0ef2, set palette = c00c0f68
[    3.557499] vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da 
[    3.557556] vesafb: scrolling: redraw
[    3.557569] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[    3.558269] Console: switching to colour frame buffer device 160x64
[    3.599577] fb0: VESA VGA frame buffer device
[    3.982230] fuse init (API version 7.9)
[    4.187382] ACPI: Invalid PBLK length [5]
[    4.187589] processor ACPI0007:00: registered as cooling_device0
[    4.261244] md: linear personality registered for level -1
[    4.278714] md: multipath personality registered for level -4
[    4.293823] md: raid0 personality registered for level 0
[    4.317138] md: raid1 personality registered for level 1
[    4.330559] xor: automatically using best checksumming function: pIII_sse
[    4.348026]    pIII_sse  :  1733.000 MB/sec
[    4.348033] xor: using function: pIII_sse (1733.000 MB/sec)
[    4.354655] async_tx: api initialized (async)
[    4.444197] raid6: int32x1    282 MB/s
[    4.512039] raid6: int32x2    288 MB/s
[    4.580111] raid6: int32x4    226 MB/s
[    4.648042] raid6: int32x8    222 MB/s
[    4.716072] raid6: mmxx1      814 MB/s
[    4.784025] raid6: mmxx2     1000 MB/s
[    4.852045] raid6: sse1x1     709 MB/s
[    4.920040] raid6: sse1x2     973 MB/s
[    4.920048] raid6: using algorithm sse1x2 (973 MB/s)
[    4.920058] md: raid6 personality registered for level 6
[    4.920065] md: raid5 personality registered for level 5
[    4.920072] md: raid4 personality registered for level 4
[    5.008961] md: raid10 personality registered for level 10
[    6.212463] No dock devices found.
[    6.620396] SCSI subsystem initialized
[    7.173436] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[    7.212153] 8139cp 0000:02:0d.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
[    7.212168] 8139cp 0000:02:0d.0: Try the "8139too" driver instead.
[    7.224080] libata version 3.00 loaded.
[    7.274526] ata_piix 0000:00:1f.1: version 2.12
[    7.274668] ata_piix 0000:00:1f.1: setting latency timer to 64
[    7.285717] scsi0 : ata_piix
[    7.293407] 8139too Fast Ethernet driver 0.9.28
[    7.353466] scsi1 : ata_piix
[    7.355090] ata1: PATA max UDMA/66 cmd 0x1f0 ctl 0x3f6 bmdma 0xb800 irq 14
[    7.355100] ata2: PATA max UDMA/66 cmd 0x170 ctl 0x376 bmdma 0xb808 irq 15
[    7.386927] usbcore: registered new interface driver usbfs
[    7.386997] usbcore: registered new interface driver hub
[    7.391705] usbcore: registered new device driver usb
[    7.402126] USB Universal Host Controller Interface driver v3.0
[    7.415693] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[    7.426603] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.524572] ata1.00: ATA-7: Hitachi HDT725032VLAT80, V54OA42A, max UDMA/133
[    7.524586] ata1.00: 625142448 sectors, multi 16: LBA48 
[    7.524787] ata1.01: ATA-4: SAMSUNG SV2044D, MM200-49, max UDMA/66
[    7.524796] ata1.01: 39862368 sectors, multi 16: LBA 
[    7.540568] ata1.00: configured for UDMA/66
[    7.556451] ata1.01: configured for UDMA/66
[    7.834018] ata2.00: ATA-8: WDC WD5000AAKB-00H8A0, 05.04E05, max UDMA/133
[    7.834032] ata2.00: 976773168 sectors, multi 16: LBA48 
[    7.834098] ata2.01: ATAPI: 4424 CDRW, 2.6C, max MWDMA1
[    7.848851] ata2.00: configured for UDMA/66
[    7.864579] ata2.01: configured for MWDMA1
[    7.864906] scsi 0:0:0:0: Direct-Access     ATA      Hitachi HDT72503 V54O PQ: 0 ANSI: 5
[    7.865302] scsi 0:0:1:0: Direct-Access     ATA      SAMSUNG SV2044D  MM20 PQ: 0 ANSI: 5
[    7.865619] scsi 1:0:0:0: Direct-Access     ATA      WDC WD5000AAKB-0 05.0 PQ: 0 ANSI: 5
[    7.868117] scsi 1:0:1:0: CD-ROM            PHILIPS  4424 CDRW        2.6C PQ: 0 ANSI: 5
[    7.868615] uhci_hcd 0000:00:1f.2: PCI INT D -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
[    7.868637] uhci_hcd 0000:00:1f.2: setting latency timer to 64
[    7.868647] uhci_hcd 0000:00:1f.2: UHCI Host Controller
[    7.868760] uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
[    7.868804] uhci_hcd 0000:00:1f.2: irq 11, io base 0x0000b400
[    7.869286] usb usb1: configuration #1 chosen from 1 choice
[    7.869378] hub 1-0:1.0: USB hub found
[    7.869406] hub 1-0:1.0: 2 ports detected
[    8.076871] 8139too 0000:02:0d.0: enabling device (0004 -> 0007)
[    8.077844] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 9
[    8.077853] PCI: setting IRQ 9 as level-triggered
[    8.077862] 8139too 0000:02:0d.0: PCI INT A -> Link[LNKB] -> GSI 9 (level, low) -> IRQ 9
[    8.077885] 8139too 0000:02:0d.0: setting latency timer to 64
[    8.079048] eth0: RealTek RTL8139 at 0xd800, 00:e0:18:c6:2c:3a, IRQ 9
[    8.079056] eth0:  Identified 8139 chip type 'RTL-8139C'
[    8.079875] ohci1394 0000:02:0e.0: enabling device (0014 -> 0016)
[    8.080994] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
[    8.081006] ohci1394 0000:02:0e.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
[    8.081019] ohci1394 0000:02:0e.0: setting latency timer to 64
[    8.131967] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11]  MMIO=[d3800000-d38007ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[    8.140761] ohci_hcd 0000:02:0a.0: enabling device (0014 -> 0016)
[    8.140791] ohci_hcd 0000:02:0a.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
[    8.140827] ohci_hcd 0000:02:0a.0: setting latency timer to 64
[    8.140836] ohci_hcd 0000:02:0a.0: OHCI Host Controller
[    8.140986] ohci_hcd 0000:02:0a.0: new USB bus registered, assigned bus number 2
[    8.141033] ohci_hcd 0000:02:0a.0: irq 11, io mem 0xd5800000
[    8.703934] usb 1-2: new full speed USB device using uhci_hcd and address 2
[    8.708075] usb usb2: configuration #1 chosen from 1 choice
[    8.708166] hub 2-0:1.0: USB hub found
[    8.708195] hub 2-0:1.0: 3 ports detected
[    8.870200] usb 1-2: configuration #1 chosen from 1 choice
[    8.875950] hub 1-2:1.0: USB hub found
[    8.876775] hub 1-2:1.0: 2 ports detected
[    9.224834] ohci_hcd 0000:02:0a.1: enabling device (0014 -> 0016)
[    9.224861] ohci_hcd 0000:02:0a.1: PCI INT B -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
[    9.224896] ohci_hcd 0000:02:0a.1: setting latency timer to 64
[    9.224905] ohci_hcd 0000:02:0a.1: OHCI Host Controller
[    9.224978] ohci_hcd 0000:02:0a.1: new USB bus registered, assigned bus number 3
[    9.225024] ohci_hcd 0000:02:0a.1: irq 11, io mem 0xd5000000
[    9.794446] usb usb3: configuration #1 chosen from 1 choice
[    9.794545] hub 3-0:1.0: USB hub found
[    9.794575] hub 3-0:1.0: 2 ports detected
[    9.852417] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[08004603005ea653]
[   10.308764] ehci_hcd 0000:02:0a.2: enabling device (0014 -> 0016)
[   10.308791] ehci_hcd 0000:02:0a.2: PCI INT C -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[   10.308824] ehci_hcd 0000:02:0a.2: setting latency timer to 64
[   10.308833] ehci_hcd 0000:02:0a.2: EHCI Host Controller
[   10.308910] ehci_hcd 0000:02:0a.2: new USB bus registered, assigned bus number 4
[   10.332078] ehci_hcd 0000:02:0a.2: irq 11, io mem 0xd4800000
[   10.344041] ehci_hcd 0000:02:0a.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004
[   10.345230] usb usb4: configuration #1 chosen from 1 choice
[   10.345352] hub 4-0:1.0: USB hub found
[   10.345383] hub 4-0:1.0: 5 ports detected
[   10.533623] scsi 0:0:0:0: Attached scsi generic sg0 type 0
[   10.533754] scsi 0:0:1:0: Attached scsi generic sg1 type 0
[   10.533866] scsi 1:0:0:0: Attached scsi generic sg2 type 0
[   10.533976] scsi 1:0:1:0: Attached scsi generic sg3 type 5
[   10.838012] Driver 'sd' needs updating - please use bus_type methods
[   10.838349] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[   10.838401] sd 0:0:0:0: [sda] Write Protect is off
[   10.838409] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   10.838491] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   10.838672] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[   10.838719] sd 0:0:0:0: [sda] Write Protect is off
[   10.838728] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   10.838807] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   10.838821]  sda: sda1 sda2
[   10.855321] sd 0:0:0:0: [sda] Attached SCSI disk
[   10.855573] sd 0:0:1:0: [sdb] 39862368 512-byte hardware sectors (20410 MB)
[   10.855626] sd 0:0:1:0: [sdb] Write Protect is off
[   10.855635] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[   10.855721] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   10.855888] sd 0:0:1:0: [sdb] 39862368 512-byte hardware sectors (20410 MB)
[   10.855936] sd 0:0:1:0: [sdb] Write Protect is off
[   10.855945] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[   10.856065] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   10.856078]  sdb:<4>Driver 'sr' needs updating - please use bus_type methods
[   10.873567]  sdb1 sdb2 sdb3
[   10.911571] sd 0:0:1:0: [sdb] Attached SCSI disk
[   10.911803] sd 1:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[   10.911856] sd 1:0:0:0: [sdc] Write Protect is off
[   10.911865] sd 1:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[   10.911950] sd 1:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   10.912177] sd 1:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[   10.912225] sd 1:0:0:0: [sdc] Write Protect is off
[   10.912234] sd 1:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[   10.912318] sd 1:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   10.912331]  sdc: sdc1
[   10.920357] sd 1:0:0:0: [sdc] Attached SCSI disk
[   10.952059] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[   10.952075] Uniform CD-ROM driver Revision: 3.20
[   10.952371] sr 1:0:1:0: Attached scsi CD-ROM sr0
[   12.008783] PM: Starting manual resume from disk
[   12.008798] PM: Resume from partition 8:18
[   12.008803] PM: Checking hibernation image.
[   12.009293] PM: Resume from disk failed.
[   12.110874] kjournald starting.  Commit interval 5 seconds
[   12.110919] EXT3-fs: mounted filesystem with ordered data mode.
[   23.266554] prism2usb_init: prism2_usb.o: 0.2.9 Loaded
[   23.266566] prism2usb_init: dev_info is: prism2_usb
[   23.266626] usbcore: registered new interface driver prism2_usb
[   23.483342] ip_tables: (C) 2000-2006 Netfilter Core Team
[   23.671922] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[   23.672434] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Plase use
[   23.672443] nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
[   23.672451] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[   24.391750] udevd version 124 started
[   26.332446] Linux agpgart interface v0.103
[   26.533525] agpgart-intel 0000:00:00.0: Intel i815 Chipset
[   26.537910] agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0xe4000000
[   26.624417] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   26.702794] intel_rng: FWH not detected
[   26.829314] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   27.028387] iTCO_vendor_support: vendor-support=0
[   27.100409] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[   27.102289] iTCO_wdt: Found a ICH TCO device (Version=1, TCOBASE=0xe460)
[   27.102670] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   27.850577] input: PC Speaker as /devices/platform/pcspkr/input/input2
[   28.027634] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[   28.044091] ACPI: Power Button (FF) [PWRF]
[   28.044445] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
[   28.056070] ACPI: Power Button (CM) [PWRB]
[   30.270156] Yenta: CardBus bridge found at 0000:02:0b.0 [13e0:0810]
[   30.407097] Yenta: ISA IRQ mask 0x0000, PCI irq 11
[   30.407110] Socket status: ffffffff
[   30.407119] Yenta: Raising subordinate bus# of parent bus (#02) from #02 to #06
[   30.407135] pcmcia: parent PCI bridge I/O window: 0xd000 - 0xdfff
[   30.407144] cs: IO port probe 0xd000-0xdfff: clean.
[   30.407634] pcmcia: parent PCI bridge Memory window: 0xd3000000 - 0xd5ffffff
[   30.407643] pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x37ffffff
[   30.464464] Yenta: CardBus bridge found at 0000:02:0b.1 [13e0:0810]
[   30.592760] Yenta: ISA IRQ mask 0x0000, PCI irq 11
[   30.592773] Socket status: ffffffff
[   30.592781] Yenta: Raising subordinate bus# of parent bus (#02) from #06 to #0a
[   30.592797] pcmcia: parent PCI bridge I/O window: 0xd000 - 0xdfff
[   30.592865] cs: IO port probe 0xd000-0xdfff: clean.
[   30.593355] pcmcia: parent PCI bridge Memory window: 0xd3000000 - 0xd5ffffff
[   30.593363] pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x37ffffff
[   31.052337] parport_pc 00:09: reported by Plug and Play ACPI
[   31.052388] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[   32.136391] input: GenPS/2 Genius Mouse as /devices/platform/i8042/serio1/input/input5
[   35.135801] Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 9 (level, low) -> IRQ 9
[   35.135845] Intel ICH 0000:00:1f.5: setting latency timer to 64
[   35.460162] intel8x0_measure_ac97_clock: measured 55836 usecs
[   35.460258] intel8x0: clocking to 48000
[   39.181012] cs: IO port probe 0x100-0x3af: excluding 0x208-0x20f 0x330-0x337
[   39.182793] cs: IO port probe 0x3e0-0x4ff: clean.
[   39.183594] cs: IO port probe 0x820-0x8ff: clean.
[   39.184485] cs: IO port probe 0xc00-0xcf7: clean.
[   39.185567] cs: IO port probe 0xa00-0xaff: clean.
[   39.193056] cs: IO port probe 0x100-0x3af: excluding 0x208-0x20f 0x330-0x337
[   39.194840] cs: IO port probe 0x3e0-0x4ff: clean.
[   39.195639] cs: IO port probe 0x820-0x8ff: clean.
[   39.196500] cs: IO port probe 0xc00-0xcf7: clean.
[   39.197577] cs: IO port probe 0xa00-0xaff: clean.
[   40.960555] lp0: using parport0 (interrupt-driven).
[   41.134736] ndiswrapper version 1.53 loaded (smp=yes, preempt=no)
[   41.196831] usbcore: registered new interface driver ndiswrapper
[   42.125897] Adding 1927792k swap on /dev/sdb2.  Priority:-1 extents:1 across:1927792k
[   42.221212] Adding 1927792k swap on /dev/sdb3.  Priority:-2 extents:1 across:1927792k
[   87.605409] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
[   87.606407] EXT3 FS on sda2, internal journal
[  105.518664] kjournald starting.  Commit interval 5 seconds
[  105.524482] EXT3 FS on sda1, internal journal
[  105.524497] EXT3-fs: mounted filesystem with ordered data mode.
[  105.902096] kjournald starting.  Commit interval 5 seconds
[  105.903524] EXT3 FS on sdc1, internal journal
[  105.903540] EXT3-fs: mounted filesystem with ordered data mode.
[  106.762008] type=1505 audit(1232537672.203:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=5023
[  107.390685] type=1505 audit(1232537672.831:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=5028
[  107.391658] type=1505 audit(1232537672.831:4): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=5028
[  108.828190] NET: Registered protocol family 17
[  109.509692] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[  111.238879] NET: Registered protocol family 10
[  111.240730] lo: Disabled Privacy Extensions
[  113.110311] warning: `ntpd' uses 32-bit capabilities (legacy support in use)
[  114.184180] ACPI: WMI: Mapper loaded
[  118.794384] apm: BIOS version 1.2 Flags 0x0b (Driver version 1.16ac)
[  118.794398] apm: overridden by ACPI.
[  119.490856] ppdev: user-space parallel port driver
[  120.656932] type=1503 audit(1232537686.102:5): operation="inode_permission" requested_mask="w::" denied_mask="w::" fsuid=0 name="/etc/krb5.conf" pid=6047 profile="/usr/sbin/cupsd"
[  121.264041] eth0: no IPv6 routers present
[  126.097151] peercast[6253]: segfault at 6e4070 ip b7ceaf20 sp bfb602e0 error 4 in libc-2.8.90.so[b7c84000+158000]

koisan1949 · 2009-01-21 23:33:15

TosaOTAKさん　dmesgの最初の部分の３行目に、Linux version 2.6.27-11-genericとありますので、
現況はやはり不具合が出そうです。

因みに私のマシンの場合、ごちゃごちゃ操作していた名残か、意図しないLinux version 2.6.27-9-server
に変わっていました。問題ないし、めんどうなのでそのままにします。参考までに提示します。

コード:

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.27-9-server (buildd@rothera) (gcc version 4.3.2 (Ubuntu 4.3.2-1ubuntu11) ) #1 SMP Thu Nov 20 22:53:41 UTC 2008 (Ubuntu 2.6.27-9.19-server)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
[    0.000000]  BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[    0.000000] last_pfn = 0x1fff0 max_arch_pfn = 0x1000000
[    0.000000] kernel direct mapping tables up to 1fff0000 @ 7000-d000
[    0.000000] RAMDISK: 1f806000 - 1ffdffaf
[    0.000000] DMI 2.2 present.
[    0.000000] ACPI: RSDP 000F6360, 0014 (r0 AOPEN )
以下　省略

カーネルソースの場所は、↓ここです。ここからdownloadして、/usr/src/にコピーしてください。
http://packages.ubuntu.com/intrepid/lin … -9-generic
ps. Xに不具合があると、上記URLでは目的のソースまで行き着けないので、直接のdebianファイル
　のURLです。http://security.ubuntu.com/ubuntu/pool/ … 9_i386.deb

それか、NVIDIAのドライバー・ユーティリティをdownloadして、カーネル2.6.27-11-genericの基で
ドライバー・モジュールを作成して入れ替えるかです。場所は、ここにあります96.43.09の中です。
ftp://download.nvidia.com/XFree86/Linux-x86/
実行の仕方は、http://forums.ubuntulinux.jp/viewtopic. … 282#p24282
ps. 1/22追記
　念のため、この方法でドライバーを入れ替えて再起動すると、起動途中は表示されますが、
　X画面には何も写りません。Xが立ち上がってないと間違った判断をしそうな状態になります。
　めげずに、ctrl+alt+F5でログインできます。(理由は不明ですが、ctrl+alt+F2を受け付けません)
　それから、xorg.confをvi等で修正し、再起動すれば正常な画面になります。

最後の編集者: koisan1949 (2009-01-22 08:13:42)

hir0 · 2009-01-22 03:55:13

ある日突然Xが起動しなくなり、CUIしか使えません。

原因を絞り込んで行くことが解決に近づくと思います。

「GeForce2カードの場合、nvidia-glxパッケージのアップグレード後にnvidia_new.koがロードされるようになるため、Xが起動しなくなる」　と言う記事もあります。

えっと、、、ログですね。カーネルオプションでVGAを指定して、Xサーバーでnvidia-glx、カーネルでvesafdを読み込んでCUIで起動。
これが順番に行われてXが起動しないのか、バラバラに読み込んでいるのかは、私では判断すら出来ません。

あっ、一つ電源？ACPIで変な記述が。でもエラーも警告も無かったので関係ないかも。

ログで解決出来る人が現れるの待つのも一つの方法ですが、もし差し支え無ければいくつか質問が有るのですが。

１、今のカーネルバージョンは手動で導入されたのですか？
２、起動オプションにVGAと書かれているのはOSインストール時に必要だったからですか？
３、8.10はクリーンインストールですか、アップデートですか？
４、PCの電源はいつも入ったままでしょうか？
５、NVIDIAのドライバはどのタイミングで導入されたのでしょうか？
６、今のドライバで通常の起動は出来ていたのでしょうか？

理由はディスプレイドライバが関係しているかどうか、他。
１、現在使用している？ドライバの導入時に勝手にインストールされるとの情報有り。＃８
２、最初の状況と5番の質問へ
３、アップデートならOSのバージョンによる不具合の可能性も。
４、ドライバ及び設定などの変更し２〜３日して再起動したら大変な事になった経験が。その時は「突然」って感じでした。

５、６、が普通なら問題は別の所に有る可能性が大。

すみません。
ログが読めないので想像で色々考えちゃって、、、

もしドライバをインストールした事が原因なら＃８と酷似しているんですが。

カーネルバージョンが変わる。
バグ？　で違うディレクトリのドライバを読み込む。
Xが起動しない。
で＃１０の方法になるんですが。

でもXが起動出来なかった時のエラーが出ていないですよね？
# dmesg | grep NVIDIA

TosaOTAK · 2009-01-25 22:28:58

何とかX起動できました。完全では有りませんが
xinit連打で何回に1回起動できます

avidya · 2009-01-25 23:16:27

　素朴な疑問ですが #1 の

2.6.27-11-generic

と Xorg.0.log のカーネルのバージョン

コード:

Build Operating System: Linux 2.6.24-19-server i686 Ubuntu

と、まったく異なるのは何故何でしょうか？
　たしかカーネル 2.6.24 は hardy で採用されていたカーネルじゃありませんでしたっけ？私の勘違い？
　私には単純に hardy から intrepid へのバージョンアップに失敗しているように見えます。

最後の編集者: avidya (2009-01-25 23:32:12)

koisan1949 · 2009-01-26 00:21:11

avidya による投稿:
Build Operating System: Linux 2.6.24-19-server i686 Ubuntu
たしかカーネル 2.6.24 は hardy で採用されていたカーネルじゃありませんでしたっけ？

仰せの通りです。
でも、カーネルソースコードを更新する毎に、全てのソースコードをダウンロードしていたのでは、たまりません。
そこで、ベースとなる旧ソースからの差分で、新しいバージョンを作成したと読めますが。。。

すなわち、Linux 2.6.24-19-server i686 Ubuntu　を基本ソースコードを利用して、
現在のカーネルである Linux fairy-desktop 2.6.27-11-generic を作成したと解釈してます。
間違っていたら、ごめんなさい。

ps. 1/26追記　Ubuntu 8.10をクリーン・インストールした最初のカーネルバージョンは、2.6.27-9 genericです。
　synapticのリポジトリーを操作した覚えはないのですが、私の場合、http://forums.ubuntulinux.jp/viewtopic. … 264#p24264で、教えてもらうまで気にしてませんでした。
　自動的にダウンロードされ、カーネルのバージョンが上がってしまいました。
　（2.6.27-9 generic　→　2.6.27-10 generic　→　2.6.27-11 generic）

最後の編集者: koisan1949 (2009-01-26 09:05:57)

avidya · 2009-01-26 05:57:02

koisan1949さんによる投稿:
仰せの通りです。
でも、カーネルソースコードを更新する毎に、全てのソースコードをダウンロードしていたのでは、たまりません。
そこで、ベースとなる旧ソースからの差分で、新しいバージョンを作成したと読めますが。。。

すなわち、Linux 2.6.24-19-server i686 Ubuntu　を基本ソースコードを利用して、
現在のカーネルである Linux fairy-desktop 2.6.27-11-generic を作成したと解釈してます。
間違っていたら、ごめんなさい。

　すいません、TosaOTAK さんの書き込みにはカーネルを再構築した話はひとつもでてませんが。それに samba のサーバが入っているからといって、Ubuntu Server を使っているとも限りませんし。
　私は単純に hardy から intrepid へのバージョンアップに失敗してるのでは？と思っているのですが。だから kiyoshi さんの

kiyoshiさんによる投稿:
sudo apt-get dist-upgrade

が正解かなと思うのですが。当然
/etc/apt/sources.list
の内容をチェックするのを前提で。

　ただどちらにせよ、私も推測で書いているので hir0 さんの質問に対して、TosaOTAK さんに答えていただくのが先決かと。

最後の編集者: avidya (2009-01-26 06:03:05)

hir0 · 2009-01-26 12:36:29

返事が無いと言うことは、もう試したもしくは試すまでもない。と言う事でNVIDIAドライバ説はボツ。
次は指摘のあった　synapticのリポジトリー　http://forums.ubuntulinux.jp/viewtopic.php?pid=24264#p24264
と　sudo apt-get dist-upgrade　ですね。　

ただどちらにせよ、私も推測で書いているので hir0 さんの質問に対して、TosaOTAK さんに答えていただくのが先決かと。

いやぁ〜質問には答えなくても大丈夫ですよ。
ただ何かアクションを起こしていただけないと、、、

TosaOTAK さんによる投稿

ある日突然Xが起動しなくなり、CUIしか使えません。

Xorg.0.logの内容です

一応2.6.27-8（2.6.27-9無いので）で起動してみましたが、
同じでした。他のカーネルも試しましたが変わりませんでした
一応dmesgの出力です

何とかX起動できました。完全では有りませんが
xinit連打で何回に1回起動できます

う〜ん、よくわかrない。
上級者の方々が顔を出してきたので何かアクションを起こすことが解決に繋がると思いますよ。
と言うことで初心者は退散します。

最後の編集者: hir0 (2009-01-26 12:39:57)

jackalope · 2009-01-26 16:51:24

koisan1949さんによる投稿:
カーネルソースの場所は、↓ここです。

Synapticでインストール可能なカーネルをインストールするのになぜカーネルソースが必要なのかな？
おまけに、リンク先の物はカーネルヘッダーですよ。

avidyaさんによる投稿:
素朴な疑問ですが #1 の

Build Operating System:はX Server 1.5.2をビルドした環境です。

koisan1949さんによる投稿:
カーネルソースコードを更新する毎に、全てのソースコードをダウンロードしていたのでは、たまりません。

通常、カーネルソースもパッケージでインストールしますので、更新があればパッケージごと入れ替えになりますよ。

koisan1949さんによる投稿:
すなわち、Linux 2.6.24-19-server i686 Ubuntu　を基本ソースコードを利用して、
現在のカーネルである Linux fairy-desktop 2.6.27-11-generic を作成したと解釈してます。
間違っていたら、ごめんなさい。

間違いです。

”すでに最新バージョンです”のメッセージがでるような気がしますが。。。
Intrepidならとりあえず、sudo apt-get install linux-image-2.6.27-9-genericかな。

avidya · 2009-01-26 17:27:03

　jackalope さん、突っ込みありがとうございます。

jackalopeさんによる投稿:
avidyaさんによる投稿:
素朴な疑問ですが #1 の
Build Operating System:はX Server 1.5.2をビルドした環境です。

　ちょっと後学のために私にも教えていただけないでしょうか。"kernel 2.6.24-19-server" でビルドした X の環境は、"kernel 2.6.27-11-generic" でも正常に動作することは担保されているのですか？

jackalope · 2009-01-27 12:07:16

端末からログインすると、Ubuntu comes with ABSOLUTELY NO WARRANTY などの表示がでますので、担保＝保証の意味でお使いなのであれば、”いいえ”でしょうね。

TosaOTAK · 2009-02-17 08:26:06

PCの相手出来ないほど忙しかったので遅れましたが、

koisan1949 による投稿:
すなわち、Linux 2.6.24-19-server i686 Ubuntu　を基本ソースコードを利用して、
現在のカーネルである Linux fairy-desktop 2.6.27-11-generic を作成したと解釈してます。
間違っていたら、ごめんなさい。

koisan1949さんの投稿を見てもしかしたら、でserver関連のkernel packageを消してXを再installしました。
そしたら正常に動作しました。
しかし何を消したかはっきり覚えていません。
皆さん数々の助言ありがとうございました。
私のグダグダにつき合わせてごめんなさい。

Ubuntu日本語フォーラム

お知らせ

#1 2009-01-19 21:49:10

突然Xが起動しなくなりました

#2 2009-01-20 01:39:32

Re: 突然Xが起動しなくなりました

#3 2009-01-20 07:12:07

Re: 突然Xが起動しなくなりました

#4 2009-01-20 08:04:49

Re: 突然Xが起動しなくなりました

#5 2009-01-20 17:46:27

Re: 突然Xが起動しなくなりました

#6 2009-01-20 20:27:34

Re: 突然Xが起動しなくなりました

#7 2009-01-20 20:38:44

Re: 突然Xが起動しなくなりました

コード:

#8 2009-01-20 22:19:04

Re: 突然Xが起動しなくなりました

#9 2009-01-21 20:52:23

Re: 突然Xが起動しなくなりました

コード:

#10 2009-01-21 23:33:15

Re: 突然Xが起動しなくなりました

コード:

#11 2009-01-22 03:55:13

Re: 突然Xが起動しなくなりました

#12 2009-01-25 22:28:58

Re: 突然Xが起動しなくなりました

#13 2009-01-25 23:16:27

Re: 突然Xが起動しなくなりました

コード:

#14 2009-01-26 00:21:11

Re: 突然Xが起動しなくなりました

avidya による投稿:

#15 2009-01-26 05:57:02

Re: 突然Xが起動しなくなりました

koisan1949さん による投稿:

kiyoshiさん による投稿:

#16 2009-01-26 12:36:29

Re: 突然Xが起動しなくなりました

#17 2009-01-26 16:51:24

Re: 突然Xが起動しなくなりました

koisan1949さん による投稿:

avidyaさん による投稿:

koisan1949さん による投稿:

koisan1949さん による投稿:

#18 2009-01-26 17:27:03

Re: 突然Xが起動しなくなりました

jackalopeさん による投稿:

avidyaさん による投稿:

#19 2009-01-27 12:07:16

Re: 突然Xが起動しなくなりました

#20 2009-02-17 08:26:06

Re: 突然Xが起動しなくなりました

koisan1949 による投稿:

Board footer

koisan1949さんによる投稿:

kiyoshiさんによる投稿:

koisan1949さんによる投稿:

avidyaさんによる投稿:

koisan1949さんによる投稿:

koisan1949さんによる投稿:

jackalopeさんによる投稿:

avidyaさんによる投稿: