下記のシステムでubuntu8.10を稼働中ですが、今回新品のSATA HDDを増設しましたところGPartedで正常に認識しません。
ただ、起動10回に1回位の割で不定期に認識することがあり、そのときパーティーションを切ろうとすると失敗し、その後認識
しなくなります。コネクタ接続、ケーブル交換等点検しましたが同じです。BIOSでは既存のHDD及び増設のHDDともに認識して
います。8.10のライブCDでも認識しません。

　　稼働中のシステム

　　　　MB       :GA-K8VM800M
         CPU      :AMD Athlon64
         Memory :1GB
         HDD      :ATA8GB QUANTUM FIREBALL A05
       　増設または取り替えようとしているHDD:SATA 160GB 　Hitachi HDT721016SLA380

当方初心者でメッセージ内容等理解できません。どなたか対処の仕方のアドバイスを求めます。
よろしくお願いします。




起動時に次のメッセージが出ることがありロックします。再起動すると正常に起動します。

********************ここから************************************
Boot from (hd0,0) ext3   71199a7c-5f05-4cec-9c90-2858fd22e7a8

Starting up...

Loading , please wait...

Gave up waiting for root device , common probrems!

-Boot args (cat/proc/cmdline)

  -check root delay =(did the system wait long enough?)

  -check root =(did the system wait for the right device?)

-Missing modules (cat/proc/moduls;ls/dev)

ALERT! /dev/disk/by-uuid/71199a7e-5f05-4cec-9c90-2858fd22e7a8

does not exist. Dropping to a shell!

Busy Box v1.10.2(ubuntu1.1.10.2-ubuntu7)built-in shell(ash)

Enter 'help'for a list of built-in commands,

(init ramfs) [34,944009] ata3:SRST failed(errno=-16)

[44.956005] ata3:SRST failed ((errno=-16)

[80.000006] ata3:SRST failed ((errno=-16)

[85.028005] ata3:SRST failed ((errno=-16)

[85.028052] ata3:SRST failed ((errno=-16)

     reset failed , giving up
********************ここまで**************************************

つぎは長くて申し訳ありませんがdmesgの全内容です。

********************ここから**************************************
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 259727
[    0.000000] Kernel command line: root=UUID=71199a7c-5f05-4cec-9c90-2858fd22e7a8 ro quiet splash
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] TSC: PIT calibration confirmed by PMTIMER.
[    0.000000] TSC: using PIT calibration value
[    0.000000] Detected 2304.504 MHz processor.
[    0.004000] Console: colour VGA+ 80x25
[    0.004000] console [tty0] enabled
[    0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.004000] Memory: 1024732k/1048512k available (2576k kernel code, 22996k reserved, 1165k data, 424k init, 131008k highmem)
[    0.004000] virtual kernel memory layout:
[    0.004000]     fixmap  : 0xffc77000 - 0xfffff000   (3616 kB)
[    0.004000]     pkmap   : 0xff400000 - 0xff800000   (4096 kB)
[    0.004000]     vmalloc : 0xf8800000 - 0xff3fe000   ( 107 MB)
[    0.004000]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
[    0.004000]       .init : 0xc04ad000 - 0xc0517000   ( 424 kB)
[    0.004000]       .data : 0xc03840da - 0xc04a7680   (1165 kB)
[    0.004000]       .text : 0xc0100000 - 0xc03840da   (2576 kB)
[    0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[    0.004000] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.004011] Calibrating delay loop (skipped), value calculated using timer frequency.. 4609.00 BogoMIPS (lpj=9218016)
[    0.004031] Security Framework initialized
[    0.004039] SELinux:  Disabled at boot.
[    0.004064] AppArmor: AppArmor initialized
[    0.004071] Mount-cache hash table entries: 512
[    0.004226] Initializing cgroup subsys ns
[    0.004230] Initializing cgroup subsys cpuacct
[    0.004232] Initializing cgroup subsys memory
[    0.004245] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[    0.004248] CPU: L2 Cache: 512K (64 bytes/line)
[    0.004261] Checking 'hlt' instruction... OK.
[    0.020388] SMP alternatives: switching to UP code
[    0.024019] Freeing SMP alternatives: 11k freed
[    0.024022] ACPI: Core revision 20080609
[    0.025453] ACPI: Checking initramfs for custom DSDT
[    0.319642] ENABLING IO-APIC IRQs
[    0.319934] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0
[    0.359629] CPU0: AMD Athlon(tm) 64 Processor 3000+ stepping 00
[    0.360022] Brought up 1 CPUs
[    0.360022] Total of 1 processors activated (4609.00 BogoMIPS).
[    0.360022] CPU0 attaching NULL sched-domain.
[    0.360022] net_namespace: 840 bytes
[    0.360022] Booting paravirtualized kernel on bare hardware
[    0.360022] Time:  8:58:02  Date: 03/11/09
[    0.360022] NET: Registered protocol family 16
[    0.360022] EISA bus registered
[    0.360022] ACPI: bus type pci registered
[    0.363435] PCI: PCI BIOS revision 2.10 entry at 0xfb140, last bus=1
[    0.363438] PCI: Using configuration type 1 for base access
[    0.364577] ACPI: EC: Look up EC in DSDT
[    0.369756] ACPI: Interpreter enabled
[    0.369764] ACPI: (supports S0 S1 S4 S5)
[    0.369779] ACPI: Using IOAPIC for interrupt routing
[    0.374830] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.374897] PCI: 0000:00:00.0 reg 10 32bit mmio: [e8000000, ebffffff]
[    0.375069] pci 0000:00:01.0: supports D1
[    0.375096] PCI: 0000:00:0a.0 reg 10 io port: [9000, 901f]
[    0.375122] pci 0000:00:0a.0: supports D1
[    0.375124] pci 0000:00:0a.0: supports D2
[    0.375143] PCI: 0000:00:0b.0 reg 10 32bit mmio: [ee000000, ee00ffff]
[    0.375148] PCI: 0000:00:0b.0 reg 14 io port: [9400, 9407]
[    0.375172] pci 0000:00:0b.0: PME# supported from D0
[    0.375176] pci 0000:00:0b.0: PME# disabled
[    0.375198] PCI: 0000:00:0f.0 reg 10 io port: [9800, 9807]
[    0.375204] PCI: 0000:00:0f.0 reg 14 io port: [9c00, 9c03]
[    0.375209] PCI: 0000:00:0f.0 reg 18 io port: [a000, a007]
[    0.375214] PCI: 0000:00:0f.0 reg 1c io port: [a400, a403]
[    0.375220] PCI: 0000:00:0f.0 reg 20 io port: [a800, a80f]
[    0.375225] PCI: 0000:00:0f.0 reg 24 io port: [ac00, acff]
[    0.375270] PCI: 0000:00:0f.1 reg 20 io port: [b000, b00f]
[    0.375323] PCI: 0000:00:10.0 reg 20 io port: [b400, b41f]
[    0.375339] pci 0000:00:10.0: supports D1
[    0.375340] pci 0000:00:10.0: supports D2
[    0.375342] pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.375345] pci 0000:00:10.0: PME# disabled
[    0.375376] PCI: 0000:00:10.1 reg 20 io port: [b800, b81f]
[    0.375392] pci 0000:00:10.1: supports D1
[    0.375393] pci 0000:00:10.1: supports D2
[    0.375395] pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.375398] pci 0000:00:10.1: PME# disabled
[    0.375429] PCI: 0000:00:10.2 reg 20 io port: [bc00, bc1f]
[    0.375445] pci 0000:00:10.2: supports D1
[    0.375446] pci 0000:00:10.2: supports D2
[    0.375448] pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.375451] pci 0000:00:10.2: PME# disabled
[    0.375481] PCI: 0000:00:10.3 reg 20 io port: [c000, c01f]
[    0.375497] pci 0000:00:10.3: supports D1
[    0.375499] pci 0000:00:10.3: supports D2
[    0.375501] pci 0000:00:10.3: PME# supported from D0 D1 D2 D3hot D3cold
[    0.375504] pci 0000:00:10.3: PME# disabled
[    0.375523] PCI: 0000:00:10.4 reg 10 32bit mmio: [ee010000, ee0100ff]
[    0.375551] pci 0000:00:10.4: supports D1
[    0.375552] pci 0000:00:10.4: supports D2
[    0.375554] pci 0000:00:10.4: PME# supported from D0 D1 D2 D3hot D3cold
[    0.375557] pci 0000:00:10.4: PME# disabled
[    0.375603] HPET not enabled in BIOS. You might try hpet=force boot option
[    0.375634] PCI: 0000:00:12.0 reg 10 io port: [c400, c4ff]
[    0.375639] PCI: 0000:00:12.0 reg 14 32bit mmio: [ee011000, ee0110ff]
[    0.375663] pci 0000:00:12.0: supports D1
[    0.375665] pci 0000:00:12.0: supports D2
[    0.375667] pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.375670] pci 0000:00:12.0: PME# disabled
[    0.375736] PCI: 0000:01:00.0 reg 10 32bit mmio: [ec000000, ecffffff]
[    0.375740] PCI: 0000:01:00.0 reg 14 32bit mmio: [e0000000, e7ffffff]
[    0.375750] PCI: 0000:01:00.0 reg 30 32bit mmio: [0, 1ffff]
[    0.375778] PCI: bridge 0000:00:01.0 32bit mmio: [ec000000, edffffff]
[    0.375782] PCI: bridge 0000:00:01.0 32bit mmio pref: [e0000000, e7ffffff]
[    0.375787] bus 00 -> node 0
[    0.375793] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.414030] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12)
[    0.414189] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
[    0.414352] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 *11 12)
[    0.414515] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *5
[    0.414652] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
[    0.414782] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
[    0.414913] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
[    0.415048] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
[    0.415240] ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0
[    0.415435] ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0
[    0.415651] ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0
[    0.415845] ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0
[    0.415979] Linux Plug and Play Support v0.97 (c) Adam Belay
[    0.416006] pnp: PnP ACPI init
[    0.416012] ACPI: bus type pnp registered
[    0.419438] pnp: PnP ACPI: found 13 devices
[    0.419441] ACPI: ACPI bus type pnp unregistered
[    0.419444] PnPBIOS: Disabled by ACPI PNP
[    0.419730] PCI: Using ACPI for IRQ routing
[    0.419836] NET: Registered protocol family 8
[    0.419836] NET: Registered protocol family 20
[    0.419836] NetLabel: Initializing
[    0.419836] NetLabel:  domain hash size = 128
[    0.419836] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.419836] NetLabel:  unlabeled traffic allowed by default
[    0.420212] tracer: 772 pages allocated for 65536 entries of 48 bytes
[    0.420214]    actual entries 65620
[    0.420383] AppArmor: AppArmor Filesystem Enabled
[    0.420398] ACPI: RTC can wake from S4
[    0.420427] system 00:00: iomem range 0xd0000-0xd7fff has been reserved
[    0.420430] system 00:00: iomem range 0xf0000-0xf7fff could not be reserved
[    0.420432] system 00:00: iomem range 0xf8000-0xfbfff could not be reserved
[    0.420435] system 00:00: iomem range 0xfc000-0xfffff could not be reserved
[    0.420438] system 00:00: iomem range 0x3fff0000-0x3fffffff could not be reserved
[    0.420441] system 00:00: iomem range 0xffff0000-0xffffffff could not be reserved
[    0.420443] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[    0.420446] system 00:00: iomem range 0x100000-0x3ffeffff could not be reserved
[    0.420449] system 00:00: iomem range 0xfec00000-0xfec00fff could not be reserved
[    0.420452] system 00:00: iomem range 0xfee00000-0xfee00fff could not be reserved
[    0.420455] system 00:00: iomem range 0xfff80000-0xfffeffff has been reserved
[    0.420461] system 00:02: ioport range 0x4000-0x407f has been reserved
[    0.420463] system 00:02: ioport range 0x40f0-0x40ff has been reserved
[    0.420466] system 00:02: ioport range 0x5000-0x500f has been reserved
[    0.420472] system 00:03: ioport range 0x4d0-0x4d1 has been reserved
[    0.420474] system 00:03: ioport range 0x290-0x29f has been reserved
[    0.420477] system 00:03: ioport range 0x800-0x805 has been reserved
[    0.455398] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[    0.455401] pci 0000:00:01.0:   IO window: disabled
[    0.455405] pci 0000:00:01.0:   MEM window: 0xec000000-0xedffffff
[    0.455409] pci 0000:00:01.0:   PREFETCH window: 0x000000e0000000-0x000000e7ffffff
[    0.455420] pci 0000:00:01.0: setting latency timer to 64
[    0.455423] bus: 00 index 0 io port: [0, ffff]
[    0.455425] bus: 00 index 1 mmio: [0, ffffffff]
[    0.455427] bus: 01 index 0 mmio: [0, 0]
[    0.455429] bus: 01 index 1 mmio: [ec000000, edffffff]
[    0.455431] bus: 01 index 2 mmio: [e0000000, e7ffffff]
[    0.455433] bus: 01 index 3 mmio: [0, 0]
[    0.455444] NET: Registered protocol family 2
[    0.455550] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.455855] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.456820] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.457330] TCP: Hash tables configured (established 131072 bind 65536)
[    0.457333] TCP reno registered
[    0.457432] NET: Registered protocol family 1
[    0.457563] checking if image is initramfs... it is
[    0.956073] Switched to high resolution mode on CPU 0
[    1.069807] Freeing initrd memory: 8008k freed
[    1.070454] audit: initializing netlink socket (disabled)
[    1.070472] type=2000 audit(1236761882.068:1): initialized
[    1.075697] highmem bounce pool size: 64 pages
[    1.075703] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    1.077479] VFS: Disk quotas dquot_6.5.1
[    1.077546] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.077631] msgmni has been set to 1761
[    1.077734] io scheduler noop registered
[    1.077736] io scheduler anticipatory registered
[    1.077738] io scheduler deadline registered
[    1.077748] io scheduler cfq registered (default)
[    1.077763] PCI: VIA PCI bridge detected.Disabling DAC.
[    1.077842] pci 0000:01:00.0: Boot video device
[    1.078106] isapnp: Scanning for PnP cards...
[    1.431477] isapnp: No Plug & Play device found
[    1.460751] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[    1.460858] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.460977] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[    1.461469] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.461719] 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[    1.463124] brd: module loaded
[    1.463183] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[    1.463278] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[    1.463281] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[    1.463400] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.463740] mice: PS/2 mouse device common for all mice
[    1.463849] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[    1.463881] rtc0: alarms up to one year, y3k
[    1.463980] EISA: Probing bus 0 at eisa.0
[    1.463997] Cannot allocate resource for EISA slot 4
[    1.463999] Cannot allocate resource for EISA slot 5
[    1.464024] EISA: Detected 0 cards.
[    1.464027] cpuidle: using governor ladder
[    1.464029] cpuidle: using governor menu
[    1.464453] TCP cubic registered
[    1.464479] Using IPI No-Shortcut mode
[    1.464637] registered taskstats version 1
[    1.464739]   Magic number: 1:97:978
[    1.464756] tty ttyc5: hash matches
[    1.464905] rtc_cmos 00:05: setting system clock to 2009-03-11 08:58:03 UTC (1236761883)
[    1.464908] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    1.464910] EDD information not available.
[    1.465241] Freeing unused kernel memory: 424k freed
[    1.465293] Write protecting the kernel text: 2580k
[    1.465324] Write protecting the kernel read-only data: 940k
[    1.486936] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[    1.705218] fuse init (API version 7.9)
[    1.918436] processor ACPI0007:00: registered as cooling_device0
[    2.516185] No dock devices found.
[    2.559935] SCSI subsystem initialized
[    2.645337] libata version 3.00 loaded.
[    2.653104] usbcore: registered new interface driver usbfs
[    2.653129] usbcore: registered new interface driver hub
[    2.670047] usbcore: registered new device driver usb
[    2.678911] sata_via 0000:00:0f.0: version 2.3
[    2.679211] ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0, using IRQ 20
[    2.679213] ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
[    2.679220] sata_via 0000:00:0f.0: PCI INT B -> Link[ALKA] -> GSI 20 (level, low) -> IRQ 20
[    2.679258] sata_via 0000:00:0f.0: routed to hard irq line 11
[    2.681281] scsi0 : sata_via
[    2.692124] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[    2.700043] scsi1 : sata_via
[    2.700114] ata1: SATA max UDMA/133 cmd 0x9800 ctl 0x9c00 bmdma 0xa800 irq 20
[    2.700117] ata2: SATA max UDMA/133 cmd 0xa000 ctl 0xa400 bmdma 0xa808 irq 20
[    2.717108] USB Universal Host Controller Interface driver v3.0
[    2.904083] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    3.068197] ata1.00: ATA-8: Hitachi HDT721016SLA380, ST1OA31B, max UDMA/133
[    3.068202] ata1.00: 268435455 sectors, multi 16: LBA NCQ (depth 0/17)
[    3.084180] ata1.00: model number mismatch 'Hitachi HDT721016SLA380' != 'HitachA002T721K8EBLA38'
[    3.084185] ata1.00: revalidation failed (errno=-19)
[    3.084191] ata1.00: limiting speed to UDMA/133:PIO3
[    8.264010] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    8.436178] ata1.00: n_sectors mismatch 268435455 != 5144164111204062831
[    8.436181] ata1.00: revalidation failed (errno=-19)
[    8.436185] ata1.00: disabled
[    8.640009] ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
[    8.640109] pata_via 0000:00:0f.1: version 0.3.3
[    8.640127] pata_via 0000:00:0f.1: PCI INT A -> Link[ALKA] -> GSI 20 (level, low) -> IRQ 20
[    8.640255] scsi2 : pata_via
[    8.640601] scsi3 : pata_via
[    8.642209] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xb000 irq 14
[    8.642212] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xb008 irq 15
[    8.812292] ata3.00: HPA unlocked: 16511951 -> 16514064, native 16514064
[    8.812298] ata3.00: ATA-4: QUANTUM FIREBALLlct08 08, A05.0X00, max UDMA/66
[    8.812301] ata3.00: 16514064 sectors, multi 16: LBA
[    8.828450] ata3.00: configured for UDMA/66
[    9.000299] ata4.00: ATAPI: HL-DT-ST DVDRAM GSA-4120B, A110, max UDMA/33
[    9.000319] ata4.01: ATAPI: FUJITSU MCC3064AP, 0051, max MWDMA2
[    9.016196] ata4.00: configured for UDMA/33
[    9.032192] ata4.01: configured for MWDMA2
[    9.032284] scsi 2:0:0:0: Direct-Access     ATA      QUANTUM FIREBALL A05. PQ: 0 ANSI: 5
[    9.036211] scsi 3:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-4120B A110 PQ: 0 ANSI: 5
[    9.037393] scsi 3:0:1:0: Optical Device    FUJITSU  M25-MCC3064AP    0051 PQ: 0 ANSI: 5
[    9.037766] ACPI: PCI Interrupt Link [ALKB] BIOS reported IRQ 0, using IRQ 21
[    9.037768] ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
[    9.037775] uhci_hcd 0000:00:10.0: PCI INT A -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[    9.037785] uhci_hcd 0000:00:10.0: UHCI Host Controller
[    9.037823] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[    9.037854] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000b400
[    9.038007] usb usb1: configuration #1 chosen from 1 choice
[    9.038030] hub 1-0:1.0: USB hub found
[    9.038039] hub 1-0:1.0: 2 ports detected
[    9.247171] uhci_hcd 0000:00:10.1: PCI INT A -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[    9.247183] uhci_hcd 0000:00:10.1: UHCI Host Controller
[    9.247216] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[    9.247239] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000b800
[    9.247360] usb usb2: configuration #1 chosen from 1 choice
[    9.247384] hub 2-0:1.0: USB hub found
[    9.247392] hub 2-0:1.0: 2 ports detected
[    9.452235] uhci_hcd 0000:00:10.2: PCI INT B -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[    9.452247] uhci_hcd 0000:00:10.2: UHCI Host Controller
[    9.452267] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[    9.452289] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000bc00
[    9.452375] usb usb3: configuration #1 chosen from 1 choice
[    9.452401] hub 3-0:1.0: USB hub found
[    9.452409] hub 3-0:1.0: 2 ports detected
[    9.660596] uhci_hcd 0000:00:10.3: PCI INT B -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[    9.660610] uhci_hcd 0000:00:10.3: UHCI Host Controller
[    9.660806] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[    9.660829] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000c000
[    9.661685] usb usb4: configuration #1 chosen from 1 choice
[    9.661895] hub 4-0:1.0: USB hub found
[    9.661904] hub 4-0:1.0: 2 ports detected
[    9.868660] ehci_hcd 0000:00:10.4: PCI INT C -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[    9.868674] ehci_hcd 0000:00:10.4: EHCI Host Controller
[    9.868698] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
[    9.868733] ehci_hcd 0000:00:10.4: irq 21, io mem 0xee010000
[    9.980011] usb 4-1: new full speed USB device using uhci_hcd and address 2
[    9.992006] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    9.992429] usb usb5: configuration #1 chosen from 1 choice
[    9.992672] hub 5-0:1.0: USB hub found
[    9.992683] hub 5-0:1.0: 8 ports detected
[   10.048034] hub 4-0:1.0: unable to enumerate USB device on port 1
[   10.201038] ACPI: PCI Interrupt Link [ALKD] BIOS reported IRQ 0, using IRQ 23
[   10.201042] ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
[   10.201049] via-rhine 0000:00:12.0: PCI INT A -> Link[ALKD] -> GSI 23 (level, low) -> IRQ 23
[   10.201307] eth0: VIA Rhine II at 0xee011000, 00:16:e6:44:bf:19, IRQ 23.
[   10.201923] eth0: MII PHY found at address 1, status 0x7869 advertising 05e1 Link 41e1.
[   10.216048] scsi 2:0:0:0: Attached scsi generic sg0 type 0
[   10.216081] scsi 3:0:0:0: Attached scsi generic sg1 type 5
[   10.216111] scsi 3:0:1:0: Attached scsi generic sg2 type 7
[   10.320210] Driver 'sd' needs updating - please use bus_type methods
[   10.320318] sd 2:0:0:0: [sda] 16514064 512-byte hardware sectors (8455 MB)
[   10.320333] sd 2:0:0:0: [sda] Write Protect is off
[   10.320335] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   10.320354] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   10.320411] sd 2:0:0:0: [sda] 16514064 512-byte hardware sectors (8455 MB)
[   10.320422] sd 2:0:0:0: [sda] Write Protect is off
[   10.320424] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   10.320442] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   10.320446]  sda:<4>Driver 'sr' needs updating - please use bus_type methods
[   10.335292]  sda1 sda2 < sda5 >
[   10.356541] sd 2:0:0:0: [sda] Attached SCSI disk
[   10.365980] sd 3:0:1:0: [sdb] Attached SCSI removable disk
[   10.387149] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[   10.387154] Uniform CD-ROM driver Revision: 3.20
[   10.387243] sr 3:0:0:0: Attached scsi CD-ROM sr0
[   10.560028] usb 4-1: new full speed USB device using uhci_hcd and address 3
[   10.710602] usb 4-1: configuration #1 chosen from 1 choice
[   10.712763] hub 4-1:1.0: USB hub found
[   10.715912] hub 4-1:1.0: 4 ports detected
[   10.818561] PM: Starting manual resume from disk
[   10.818566] PM: Resume from partition 8:5
[   10.818567] PM: Checking hibernation image.
[   10.818892] PM: Resume from disk failed.
[   10.877266] kjournald starting.  Commit interval 5 seconds
[   10.877278] EXT3-fs: mounted filesystem with ordered data mode.
[   20.868887] udevd version 124 started
[   21.559822] Linux agpgart interface v0.103
[   21.640164] agpgart-amd64 0000:00:00.0: AGP bridge [1106/0204]
[   21.642548] agpgart-amd64 0000:00:00.0: AGP aperture is 64M @ 0xe8000000
[   21.688169] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   21.732212] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   22.076255] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[   22.088051] ACPI: Power Button (FF) [PWRF]
[   22.088160] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
[   22.108031] ACPI: Power Button (CM) [PWRB]
[   22.588218] parport_pc 00:0b: reported by Plug and Play ACPI
[   22.588256] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[   23.612136] nvidia: module license 'NVIDIA' taints kernel.
[   23.949523] input: PC Speaker as /devices/platform/pcspkr/input/input4
[   24.000643] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   24.000888] NVRM: loading NVIDIA UNIX x86 Kernel Module  173.14.12  Thu Jul 17 18:11:36 PDT 2008
[   24.337748] CA0106 0000:00:0a.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[   24.337778] snd-ca0106: Model 1006 Rev 00000000 Serial 10061102
[   25.850530] lp0: using parport0 (interrupt-driven).
[   25.953598] Adding 393552k swap on /dev/sda5.  Priority:-1 extents:1 across:393552k
[   26.609054] EXT3 FS on sda1, internal journal
[   27.831497] type=1505 audit(1236761910.110:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=3941
[   28.026568] type=1505 audit(1236761910.306:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=3946
[   28.026833] type=1505 audit(1236761910.306:4): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=3946
[   28.197470] ip_tables: (C) 2000-2006 Netfilter Core Team
[   28.767517] ACPI: WMI: Mapper loaded
[   29.196178] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3000+ processors (1 cpu cores) (version 2.20.00)
[   29.196202] ACPI Exception (processor_perflib-0266): AE_NOT_FOUND, Evaluating _PSS [20080609]
[   29.201568] powernow-k8: BIOS error - no PSB or ACPI _PSS objects
[   29.222804] ACPI Exception (processor_perflib-0266): AE_NOT_FOUND, Evaluating _PSS [20080609]
[   30.020733] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[   30.121015] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[   30.121021] apm: overridden by ACPI.
[   30.319986] ppdev: user-space parallel port driver
[   33.216194] Bluetooth: Core ver 2.13
[   33.217781] NET: Registered protocol family 31
[   33.217785] Bluetooth: HCI device and connection manager initialized
[   33.217789] Bluetooth: HCI socket layer initialized
[   33.253233] Bluetooth: L2CAP ver 2.11
[   33.253237] Bluetooth: L2CAP socket layer initialized
[   33.261515] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   33.261519] Bluetooth: BNEP filters: protocol multicast
[   33.297796] Bridge firewalling registered
[   33.314764] Bluetooth: SCO (Voice Link) ver 0.6
[   33.314769] Bluetooth: SCO socket layer initialized
[   33.469838] Bluetooth: RFCOMM socket layer initialized
[   33.470159] Bluetooth: RFCOMM TTY layer initialized
[   33.470163] Bluetooth: RFCOMM ver 1.10
[   37.580957] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[   37.927734] NET: Registered protocol family 17
[   38.723639] agpgart-amd64 0000:00:00.0: AGP 3.0 bridge
[   38.723651] agpgart-amd64 0000:00:00.0: putting AGP V3 device into 8x mode
[   38.723706] nvidia 0000:01:00.0: putting AGP V3 device into 8x mode
[   44.033043] NET: Registered protocol family 10
[   44.034755] lo: Disabled Privacy Extensions
[   50.033103] usb 4-1.1: new low speed USB device using uhci_hcd and address 4
[   50.183053] usb 4-1.1: configuration #1 chosen from 1 choice
[   50.267979] usbcore: registered new interface driver hiddev
[   50.285500] input: Elecom PRUMIE series (RF) Elecom PRUMIE series (RF) as /devices/pci0000:00/0000:00:10.3/usb4/4-1/4-1.1/4-1.1:1.0/input/input5
[   50.287165] input,hidraw0: USB HID v1.11 Mouse [Elecom PRUMIE series (RF) Elecom PRUMIE series (RF)] on usb-0000:00:10.3-1.1
[   50.288238] usbcore: registered new interface driver usbhid
[   50.288782] usbhid: v2.6:USB HID core driver
[  137.896012] usb 5-5: new high speed USB device using ehci_hcd and address 3
[  138.041821] usb 5-5: configuration #1 chosen from 1 choice
[  138.144612] usbcore: registered new interface driver libusual
[  138.156229] Initializing USB Mass Storage driver...
[  138.159334] scsi4 : SCSI emulation for USB Mass Storage devices
[  138.160419] usbcore: registered new interface driver usb-storage
[  138.161024] USB Mass Storage support registered.
[  138.161592] usb-storage: device found at 3
[  138.161595] usb-storage: waiting for device to settle before scanning
[  143.160141] usb-storage: device scan complete
[  143.161120] scsi 4:0:0:0: Direct-Access     A-DATA   USB Flash Drive  0.00 PQ: 0 ANSI: 2
[  143.162233] sd 4:0:0:0: [sdc] 7897088 512-byte hardware sectors (4043 MB)
[  143.167638] sd 4:0:0:0: [sdc] Write Protect is off
[  143.167643] sd 4:0:0:0: [sdc] Mode Sense: 00 00 00 00
[  143.167646] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[  143.189143] sd 4:0:0:0: [sdc] 7897088 512-byte hardware sectors (4043 MB)
[  143.191189] sd 4:0:0:0: [sdc] Write Protect is off
[  143.191195] sd 4:0:0:0: [sdc] Mode Sense: 00 00 00 00
[  143.191198] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[  143.191635]  sdc: sdc1
[  143.834633] sd 4:0:0:0: [sdc] Attached SCSI removable disk
[  143.834987] sd 4:0:0:0: Attached scsi generic sg3 type 0
[  165.638865] ppdev0: registered pardevice
[  165.688018] ppdev0: unregistered pardevice
[  165.980195] ppdev0: registered pardevice
[  166.028210] ppdev0: unregistered pardevice
[  166.629640] ppdev0: registered pardevice
[  166.676134] ppdev0: unregistered pardevice
[  220.433670] usb 5-5: USB disconnect, address 3
[  236.317866] usb 4-1.1: USB disconnect, address 4
[  255.665095] usb 4-1.1: new low speed USB device using uhci_hcd and address 5
[  255.809282] usb 4-1.1: configuration #1 chosen from 1 choice
[  255.833492] input: Elecom PRUMIE series (RF) Elecom PRUMIE series (RF) as /devices/pci0000:00/0000:00:10.3/usb4/4-1/4-1.1/4-1.1:1.0/input/input6
[  255.860168] input,hidraw0: USB HID v1.11 Mouse [Elecom PRUMIE series (RF) Elecom PRUMIE series (RF)] on usb-0000:00:10.3-1.1
[ 1300.460541] NVRM: Xid (0001:00): 13, 0000 01019700 00003497 00001a04 01010200 00000002
[ 1300.545621] NVRM: Xid (0001:00): 13, 0000 01016100 0000008a 00000400 ffffff38 00004000
[ 1363.480343] NVRM: Xid (0001:00): 6, PE0000 140c 00106400 0000fdbc 000000ff 00106400
[ 1363.504129] NVRM: Xid (0001:00): 13, 0000 01016100 0000008a 00000400 fff2eeeb 00004000
************************ここまで*********************************************************