Ubuntu日本語フォーラム
ログインしていません。
お知らせ
#1 2009-04-22 15:15:07
- taka35
- 新しいメンバ
- 登録日: 2009-04-22
デュアルディスプレイ表示の問題
はじめまして、最近ubuntuを使い始めたものです。
デュアルディプレイ表示にする方法を教えて頂きたく、投稿しました。
いろいろ調べて行ったことを以下に記載します。
ハード 及び ソフト
OS : utuntu 8.10
CPU : pentium4
グラボ : ATI X1600
ドライバ : ATI/AMD proprietary FGLRX graphics driver
※ati-driver-installer-9-3-x86.x86_64.runでインストールしたものと思っています。＾＾；
モニター: 1280x1024 ディスプレイ2台
状況その１
1. 上記のドライバをインストール。
2. 「sudo aticonfig --initial --input=/etc/X11/xorg.conf」 を実行 (あまり意味ない？)
3. 「sudo aticonfig --initial --dtop=horiontal --screen-layout=right」 を実行
4. 再起動 しました
5. 「ユーザ名:」の入力画面では、左モニターのみに入力欄が表示されます。右モニターにはバックグランド画面のみ表示(明るい土色)
6. ログイン後は、左右のモニターにまったく同じものが表示されます。（クローンモードと思われます）
7. 端末を開いて、「vi /etc/X11/xorg.conf」後、設定を見ましたが理解できずに閉じました。(「:q!」実行)
8. 失敗ですね
と、ここまでが第１段階です。つぎに、いろいろ調べていうちにインストーラーの存在を知り、以下の作業をしました
状況その2(11.より開始)
11. ドライバーと思ってダウンロードした 'ati-driver-installer-9-3-x86.x86_64.run ' を、 /etc/X11/ にコピーして 「./ati-drive~」を実行
12. 英語がほとんど理解できないながらも勝手に解釈してすすんでいくと、GUIのインストーラーが起動しました
13. あとは自分の目的にあわせた設定を行い、インストーラー画面をとじる
14. この段階では、きちんとしたデュアルディスプレイとして動作しています
15. 再起動 しました
16. (状況その１ の 5. と同様)
17. (状況その１ の 6. と同様)
18. xorg.conf は (状況その１ の 7.) のものと同じで変更はされていませんでした
19. 14.の段階では成功ですが、最終的には失敗？
そして、新たな展開がありました。(状況その2 の 18.)は、rootでログインしていないためではないかと考え、
rootでログインできるように設定(方法はこのフォーラムより参照)し、以下の作業をすると・・・
状況その3(21.より開始)
21. (状況その１ の 5. と同様)
22. ログインしたら、なんと(状況その2 の 14.)とおなじ画面が表示され、アプリケーションも正常に動きます
23. etc/X11/xorg.conf は,この状況でも (状況その１ の 7.) のものと同じで変更はされていませんでした
24. root 専用の xorg.conf が、他に存在していないか検索しましたが、それらしいものは見つけることができませんでした
25. root以外では、失敗です。そもそも、rootログイン自体が反則？ ＾＾；
以上が、いままでの状況です。 root以外のログインでも、正常に表示されるようにしたいのですが、行き詰まっています。
どなたか、ご指導ください。お願いします。
オフライン
#2 2009-04-22 21:35:48
- STGSAGWAN
- ゲスト
Re: デュアルディスプレイ表示の問題
一般ユーザで、
$ sudo ./ati-driver-installer-9-3-x86.x86_64.run
は試されましたか？
#3 2009-04-23 01:11:49
- taka35
- 新しいメンバ
- 登録日: 2009-04-22
Re: デュアルディスプレイ表示の問題
はい。以下の2ヶ所の段階で作業しました。
・状況その1 1. 上記のドライバをインストール
・状況その2 11. (こちらの記述漏れです.次の表現が正しいです)「sudo ./ati-drive~」を実行
それから、状況その2 13〜15に関連することですが、ATIの設定アプリケーション以外でも
デュアルディスプレイ表示になることを確認しました。
それは以下の方法です。
1. 端末をひらく
2. 「grandr」もしくは「lxrandr」を起動する
3. modes(grandrの場合) か Resolition(lxrandrの場合) を 2560x1024 に設定する
4. デュアルディスプレイ表示(2画面で2560x1024)が正常に表示される
5. 再起動すると 1280x1024 のクローン画面に戻っている
このことから、ドライバーのインストールもさることながら、
設定した情報が再起動後に、root以外では認識されていない
のではないかと思われます。
引き続き、みなさまのご指導をお待ちします。よろしく、お願い致します。
オフライン
#4 2009-04-23 09:13:21
- LinuxBeginner
- メンバ
- 登録日: 2008-02-18
Re: デュアルディスプレイ表示の問題
私はeeePCの1024×600に、外付けで1280×1024のLCDパネルを接続して使っています。
条件は違いますが、「5. 再起動すると（ 1280x1024 の）クローン画面に戻っている」は同じように悩みまして、
結果、下記の対策でとりあえず解決したため、ご参考まで。
【xorg.confの編集】
$ sudo gedit /etc/X11/xorg.conf
Section "Screen"
Identifier "Default Screen"
Monitor "Configured Monitor"
Device "Configured Video Device"
Subsection "Display" ←ここから
Virtual 2304 1624 ← （ここの値はディスプレイの表示領域の合計を超えていればOK）
EndSubsection ←ここまでを追加
EndSection
【詳細】 http://d.hatena.ne.jp/rx7/20081009/p2
なお、ディスプレイの設定は、標準メニューの システム→設定→画面の解像度 で行っています。
最後の編集者: LinuxBeginner (2009-04-23 09:14:31)
オフライン
#5 2009-04-24 00:01:15
- taka35
- 新しいメンバ
- 登録日: 2009-04-22
Re: デュアルディスプレイ表示の問題
情報ありがとうございます。
早速、設定して再起動しました。
そして、ログイン画面で「ｕｂｕｎｔｕ」の文字がチラつきなら(水平同期があっていないのかな)4個並んで
表示されてフリーズ状態。
気を取り直して、CUIモードで、xorg.confを元に戻して、再起動すると、ログイン画面が真っ黒・・・・
たまに、バックグランド画面と同じ色の線がチラチラ表示される状態・・・・
その後、xorg.confの設定ををいろいろ変更して再起動しましたが、状況は変わりませんでした。
結局、再インストールしてもう一度設定しました。
そして、無事希望どおりの画面が表示され解決しました。^^
その時の手順を以下に記載します。ただし、私の環境だけでかもしれませんのでご注意を。
1. ubuntuを再インストールする
2. ATIの最新ドライバ(最初のページに記載しているもの)をダウンロードする
3. 'ati-driver-installer-9-3-x86.x86_64.run ' を、 /etc/X11/ にコピーして 「sudo ./ati-drive-installer-9-3-x86.x86_64.run」を実行
4. ドライバをインストールする。(表示されたメニューをよく見てくださいね)
5. ドライバのインストール終了
6. もう一度、「sudo ./ati-drive-installer-9-3-x86.x86_64.run」を実行(GUIの画面設定アプリケーションをインストールするため)
7. 画面設定アプリケーションをインストールする。(表示されたメニューをよく見てくださいね。ドライバかパッケージかの二択になっています)
8. 画面を進めていくうちに、Linuxの種類をきいてきますがubuntuがないので、わたしは「RedHat 5〜」を選択しました（結果はOK）
9. 画面設定アプリケーションのインストール終了
10. 再起動
11. アプリケーションメニューに「ATI Catalyst Control Center」が追加されています。(sudo用もできるかも知れませんが、私は削除しました)
12. そのアプリケーションを開いて、設定します
13. 再起動
14. デュアルディスプレイ表示になりました
ここに至までに、試行錯誤の連続でしたがその過程で得た知識は私の貴重な財産になったと思います。
ご指導いただきましたみなさん、並びにインターネットに情報を提供していただいているみなさんに感謝します。
オフライン
#6 2009-04-24 01:13:59
- koisan1949
- メンバ
- From: Hyogo, Japan
- 登録日: 2007-11-11
Re: デュアルディスプレイ表示の問題
私のUbuntu8.04, P4 , 2Gb , Aopen s661FXm-US, PowerColor ATI radeon X-1650(AGP ×8)では、
downloadしたディレクトリーから実行して、問題なく設定できました。
$ sudo sh ./ati-driver-installer-9-1-x86.x86_64.run
note: これでATI Proprietary Linux Driver setupが起動し、表示に従えば簡単にインストールできました。
セッティングしたのが、何ヶ月か前だったので、私の場合、ATI Catalyst9.1が作成され、何ら支障なく動作しています。
(メニューバーのアプリケーションをクリックすると、最終項目にATI Catalyst9.1のアイコンがあります。)
コード:
参考までに、私の環境です。
# xorg.conf (X.Org X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the xorg.conf manual page.
# (Type "man xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
# sudo dpkg-reconfigure -phigh xserver-xorg
Section "InputDevice"
Identifier "Generic Keyboard"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "jp106"
Option "XkbLayout" "jp,jp"
Option "XkbOptions" "grp:alt_shift_toggle,grp_led:scroll"
Option "XkbVariant" "106,kana"
EndSection
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "CorePointer"
EndSection
Section "Device"
Identifier "Configured Video Device"
Driver "fglrx"
EndSection
Section "Monitor"
Identifier "Configured Monitor"
VendorName "Iiyama"
ModelName "Iiyama MF-8617E/T, VisionMaster"
HorizSync 27.0 - 86.0
VertRefresh 50.0 - 160.0
Gamma 1
ModeLine "640x480@60" 25.2 640 656 752 800 480 490 492 525 -hsync -vsync
ModeLine "640x480@75" 31.5 640 656 720 840 480 481 484 500 -hsync -vsync
ModeLine "640x480@85" 36.0 640 696 752 832 480 481 484 509 -hsync -vsync
ModeLine "800x600@60" 40.0 800 840 968 1056 600 601 605 628 +hsync +vsync
ModeLine "800x600@72" 50.0 800 856 976 1040 600 637 643 666 +hsync +vsync
ModeLine "800x600@75" 49.5 800 816 896 1056 600 601 604 625 +hsync +vsync
ModeLine "800x600@85" 56.3 800 832 896 1048 600 601 604 631 +hsync +vsync
ModeLine "832x624@75" 57.3 832 864 928 1152 624 625 628 667 -hsync -vsync
ModeLine "1024x768@85" 94.5 1024 1072 1168 1376 768 769 772 808 +hsync +vsync
ModeLine "1024x768@75" 78.8 1024 1040 1136 1312 768 769 772 800 +hsync +vsync
ModeLine "1024x768@70" 75.0 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
ModeLine "1024x768@60" 65.0 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
ModeLine "1152x864@75" 108.0 1152 1216 1344 1600 864 865 868 900 +hsync +vsync
ModeLine "1280x1024@75" 135.0 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync
ModeLine "1280x960@60" 102.1 1280 1360 1496 1712 960 961 964 994 -hsync +vsync
ModeLine "1280x960@85" 148.5 1280 1344 1504 1728 960 961 964 1011 +hsync +vsync
ModeLine "1280x1024@60" 108.0 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync
ModeLine "1280x960@75" 129.9 1280 1368 1504 1728 960 961 964 1002 -hsync +vsync
ModeLine "1400x1050@60" 122.6 1400 1488 1640 1880 1050 1051 1054 1087 -hsync +vsync
ModeLine "1400x1050@75" 155.8 1400 1496 1648 1896 1050 1051 1054 1096 -hsync +vsync
ModeLine "1600x1200@65" 175.5 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync
ModeLine "1600x1200@60" 162.0 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync
ModeLine "1792x1344@60" 204.8 1792 1920 2120 2448 1344 1345 1348 1394 -hsync +vsync
ModeLine "1856x1392@60" 218.3 1856 1952 2176 2528 1392 1393 1396 1439 -hsync +vsync
EndSection
Section "Screen"
Identifier "Default Screen"
Monitor "Configured Monitor"
Device "Configured Video Device"
Defaultdepth 24
Option "NoLogo" "True"
SubSection "Display"
Virtual 800 600
Depth 24
Modes "1152x864@70" "1152x864@60" "1280x1024@70" "1280x1024@60" "1024x768@70" "1024x768@60" "1280x960@70" "1024x960@60" "800x600@70" "800x600@60" "1400x1050@60" "1400x1050@70" "1600x1200@70" "1600x1200@60" "1792x1344@60" "1856x1392@60" "640x480@70" "640x480@60"
EndSubSection
EndSection
Section "ServerLayout"
Identifier "Default Layout"
screen "Default Screen"
EndSection
Section "Module"
Load "glx"
EndSectionコード:
var/log/dmesgです。 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.24-23-generic (buildd@palmer) (gcc version 4.2.4 (Ubuntu 4.2.4-1ubuntu3)) #1 SMP Wed Apr 1 21:47:28 UTC 2009 (Ubuntu 2.6.24-23.52-generic) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f400 (usable) [ 0.000000] BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000007fef0000 (usable) [ 0.000000] BIOS-e820: 000000007fef0000 - 000000007fef3000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data) [ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) [ 0.000000] 1150MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at 000f5a90 [ 0.000000] Entering add_active_range(0, 0, 524016) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 524016 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 524016 [ 0.000000] On node 0 totalpages: 524016 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 2301 pages used for memmap [ 0.000000] HighMem zone: 292339 pages, LIFO batch:31 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] DMI 2.2 present. [ 0.000000] ACPI: RSDP signature @ 0xC00F7400 checksum 0 [ 0.000000] ACPI: RSDP 000F7400, 0014 (r0 AWARD ) [ 0.000000] ACPI: RSDT 7FEF3000, 002C (r1 AWARD AWRDACPI 42302E31 AWRD 0) [ 0.000000] ACPI: FACP 7FEF3040, 0074 (r1 AWARD AWRDACPI 42302E31 AWRD 0) [ 0.000000] ACPI: DSDT 7FEF30C0, 396B (r1 AWARD AWRDACPI 1000 MSFT 100000E) [ 0.000000] ACPI: FACS 7FEF0000, 0040 [ 0.000000] ACPI: APIC 7FEF6A40, 0068 (r1 AWARD AWRDACPI 42302E31 AWRD 0) [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 15:3 APIC version 20 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) [ 0.000000] Processor #1 15:3 APIC version 20 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 20, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 80000000 (gap: 7ff00000:7ed00000) [ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519923 [ 0.000000] Kernel command line: root=UUID=c46e2baa-9367-4ab0-a437-752b86f41349 ro quiet splash [ 0.000000] mapped APIC to ffffb000 (fee00000) [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Detected 2806.525 MHz processor. [ 17.925801] Console: colour VGA+ 80x25 [ 17.925806] console [tty0] enabled [ 17.926415] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 17.926874] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 18.063110] Memory: 2065680k/2096064k available (2179k kernel code, 29116k reserved, 1008k data, 368k init, 1178560k highmem) [ 18.063121] virtual kernel memory layout: [ 18.063122] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB) [ 18.063123] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 18.063124] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 18.063125] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 18.063126] .init : 0xc0423000 - 0xc047f000 ( 368 kB) [ 18.063127] .data : 0xc0320c78 - 0xc041cdc4 (1008 kB) [ 18.063128] .text : 0xc0100000 - 0xc0320c78 (2179 kB) [ 18.063131] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 18.063194] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1 [ 18.143031] Calibrating delay using timer specific routine.. 5617.15 BogoMIPS (lpj=11234310) [ 18.143071] Security Framework initialized [ 18.143081] SELinux: Disabled at boot. [ 18.143102] AppArmor: AppArmor initialized [ 18.143108] Failure registering capabilities with primary security module. [ 18.143119] Mount-cache hash table entries: 512 [ 18.143309] Initializing cgroup subsys ns [ 18.143315] Initializing cgroup subsys cpuacct [ 18.143331] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000041d 00000000 00000000 00000000 [ 18.143342] monitor/mwait feature present. [ 18.143344] using mwait in idle threads. [ 18.143351] CPU: Trace cache: 12K uops, L1 D cache: 16K [ 18.143354] CPU: L2 cache: 1024K [ 18.143358] CPU: Physical Processor ID: 0 [ 18.143361] CPU: After all inits, caps: bfebfbff 00000000 00000000 00043180 0000041d 00000000 00000000 00000000 [ 18.143376] Compat vDSO mapped to ffffe000. [ 18.143398] Checking 'hlt' instruction... OK. [ 18.159535] SMP alternatives: switching to UP code [ 18.161718] Early unpacking initramfs... done [ 18.495643] ACPI: Core revision 20070126 [ 18.495703] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. [ 18.624696] CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 03 [ 18.624720] SMP alternatives: switching to SMP code [ 18.625691] Booting processor 1/1 eip 3000 [ 18.635844] Initializing CPU#1 [ 18.713674] Calibrating delay using timer specific routine.. 5613.14 BogoMIPS (lpj=11226287) [ 18.713686] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000041d 00000000 00000000 00000000 [ 18.713694] monitor/mwait feature present. [ 18.713702] CPU: Trace cache: 12K uops, L1 D cache: 16K [ 18.713705] CPU: L2 cache: 1024K [ 18.713707] CPU: Physical Processor ID: 0 [ 18.713710] CPU: After all inits, caps: bfebfbff 00000000 00000000 00043180 0000041d 00000000 00000000 00000000 [ 18.714102] CPU1: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 03 [ 18.714149] Total of 2 processors activated (11230.29 BogoMIPS). [ 18.714250] ENABLING IO-APIC IRQs [ 18.714427] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 18.861497] checking TSC synchronization [CPU#0 -> CPU#1]: passed. [ 18.881469] Brought up 2 CPUs [ 18.881500] CPU0 attaching sched-domain: [ 18.881504] domain 0: span 03 [ 18.881507] groups: 01 02 [ 18.881511] domain 1: span 03 [ 18.881513] groups: 03 [ 18.881516] CPU1 attaching sched-domain: [ 18.881518] domain 0: span 03 [ 18.881520] groups: 02 01 [ 18.881524] domain 1: span 03 [ 18.881526] groups: 03 [ 18.881843] net_namespace: 64 bytes [ 18.881852] Booting paravirtualized kernel on bare hardware [ 18.882644] Time: 19:18:56 Date: 04/23/09 [ 18.882675] NET: Registered protocol family 16 [ 18.882984] EISA bus registered [ 18.882993] ACPI: bus type pci registered [ 18.904875] PCI: PCI BIOS revision 2.10 entry at 0xfb4f0, last bus=1 [ 18.904878] PCI: Using configuration type 1 [ 18.904884] Setting up standard PCI resources [ 18.913871] ACPI: EC: Look up EC in DSDT [ 18.918059] ACPI: Interpreter enabled [ 18.918063] ACPI: (supports S0 S3 S4 S5) [ 18.918081] ACPI: Using IOAPIC for interrupt routing [ 18.923855] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 18.924814] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 18.940548] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 14 15) [ 18.940666] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 14 15) *0, disabled. [ 18.940781] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 14 15) [ 18.940894] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 14 15) *0, disabled. [ 18.941009] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 14 15) [ 18.941127] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 14 15) [ 18.941250] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *9 10 11 14 15) [ 18.941366] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 14 15) [ 18.941539] Linux Plug and Play Support v0.97 (c) Adam Belay [ 18.941587] pnp: PnP ACPI init [ 18.941597] ACPI: bus type pnp registered [ 18.941845] pnpacpi: exceeded the max number of mem resources: 12 [ 18.944905] pnp: PnP ACPI: found 13 devices [ 18.944908] ACPI: ACPI bus type pnp unregistered [ 18.944913] PnPBIOS: Disabled by ACPI PNP [ 18.945300] PCI: Using ACPI for IRQ routing [ 18.945306] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 18.969263] NET: Registered protocol family 8 [ 18.969266] NET: Registered protocol family 20 [ 18.969362] AppArmor: AppArmor Filesystem Enabled [ 18.973073] Time: tsc clocksource has been installed. [ 18.985269] system 00:00: iomem range 0xd0000-0xd3fff has been reserved [ 18.985273] system 00:00: iomem range 0xf0000-0xf7fff could not be reserved [ 18.985276] system 00:00: iomem range 0xf8000-0xfbfff could not be reserved [ 18.985279] system 00:00: iomem range 0xfc000-0xfffff could not be reserved [ 18.985283] system 00:00: iomem range 0x7ff00000-0x7fffffff has been reserved [ 18.985286] system 00:00: iomem range 0x7fef0000-0x7fefffff could not be reserved [ 18.985289] system 00:00: iomem range 0xffff0000-0xffffffff could not be reserved [ 18.985292] system 00:00: iomem range 0x0-0x9ffff could not be reserved [ 18.985295] system 00:00: iomem range 0x100000-0x7feeffff could not be reserved [ 18.985298] system 00:00: iomem range 0xffee0000-0xffefffff could not be reserved [ 18.985301] system 00:00: iomem range 0xfffe0000-0xfffeffff could not be reserved [ 18.985305] system 00:00: iomem range 0xfec00000-0xfecfffff could not be reserved [ 18.985313] system 00:02: ioport range 0x4d0-0x4d1 has been reserved [ 18.985316] system 00:02: ioport range 0x800-0x805 has been reserved [ 18.985319] system 00:02: ioport range 0x290-0x297 has been reserved [ 19.015883] PCI: Bridge: 0000:00:01.0 [ 19.015888] IO window: d000-dfff [ 19.015894] MEM window: e0000000-e1ffffff [ 19.015899] PREFETCH window: d0000000-dfffffff [ 19.015923] NET: Registered protocol family 2 [ 19.053147] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 19.053511] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 19.054269] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 19.054775] TCP: Hash tables configured (established 131072 bind 65536) [ 19.054778] TCP reno registered [ 19.065280] checking if image is initramfs... it is [ 19.515795] Switched to high resolution mode on CPU 0 [ 19.515953] Switched to high resolution mode on CPU 1 [ 19.724371] Freeing initrd memory: 7726k freed [ 19.725516] audit: initializing netlink socket (disabled) [ 19.725537] audit(1240514336.420:1): initialized [ 19.725859] highmem bounce pool size: 64 pages [ 19.728649] VFS: Disk quotas dquot_6.5.1 [ 19.728754] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 19.728939] io scheduler noop registered [ 19.728942] io scheduler anticipatory registered [ 19.728944] io scheduler deadline registered [ 19.728957] io scheduler cfq registered (default) [ 19.811061] Boot video device is 0000:01:00.0 [ 19.811450] isapnp: Scanning for PnP cards... [ 20.164460] isapnp: No Plug & Play device found [ 20.205289] Real Time Clock Driver v1.12ac [ 20.205432] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 20.205568] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 20.205725] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 20.206587] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 20.206960] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 20.208177] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 20.208269] input: Macintosh mouse button emulation as /devices/virtual/input/input0 [ 20.208421] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 20.208741] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 20.208749] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 20.230259] mice: PS/2 mouse device common for all mice [ 20.230433] EISA: Probing bus 0 at eisa.0 [ 20.230441] Cannot allocate resource for EISA slot 1 [ 20.230452] Cannot allocate resource for EISA slot 4 [ 20.230470] EISA: Detected 0 cards. [ 20.230475] cpuidle: using governor ladder [ 20.230477] cpuidle: using governor menu [ 20.230583] NET: Registered protocol family 1 [ 20.230620] Using IPI No-Shortcut mode [ 20.230664] registered taskstats version 1 [ 20.230758] Magic number: 5:4:345 [ 20.230873] hash matches device tty62 [ 20.230911] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 20.230913] EDD information not available. [ 20.231301] Freeing unused kernel memory: 368k freed [ 20.231334] Write protecting the kernel read-only data: 806k [ 20.256537] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 [ 21.511524] fuse init (API version 7.9) [ 21.531268] ACPI: Fan [FAN] (on) [ 21.540480] ACPI: Thermal Zone [THRM] (33 C) [ 21.742848] SCSI subsystem initialized [ 21.784421] usbcore: registered new interface driver usbfs [ 21.784478] usbcore: registered new interface driver hub [ 21.784552] libata version 3.00 loaded. [ 21.798301] usbcore: registered new device driver usb [ 21.815897] pata_sis 0000:00:02.5: version 0.5.2 [ 21.815967] ACPI: PCI Interrupt 0000:00:02.5[A] -> GSI 16 (level, low) -> IRQ 16 [ 21.826213] scsi0 : pata_sis [ 21.840232] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 21.842295] scsi1 : pata_sis [ 21.843380] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x4000 irq 14 [ 21.843385] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x4008 irq 15 [ 21.895044] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) [ 22.019662] ata1.00: ATA-7: Maxtor 6L160P0, BAJ41G20, max UDMA/133 [ 22.019669] ata1.00: 320173056 sectors, multi 16: LBA48 [ 22.020647] ata1.01: ATA-5: WDC WD400EB-11CPF0, 06.04G06, max UDMA/100 [ 22.020653] ata1.01: 78165360 sectors, multi 16: LBA [ 22.039718] ata1.00: configured for UDMA/133 [ 22.058910] ata1.01: configured for UDMA/100 [ 22.229951] Floppy drive(s): fd0 is 1.44M [ 22.252849] FDC 0 is a post-1991 82077 [ 22.381209] ata2.00: ATAPI: PIONEER DVD-RW DVR-116D, 1.03, max UDMA/66 [ 22.552818] ata2.00: configured for UDMA/66 [ 22.553077] scsi 0:0:0:0: Direct-Access ATA Maxtor 6L160P0 BAJ4 PQ: 0 ANSI: 5 [ 22.553332] scsi 0:0:1:0: Direct-Access ATA WDC WD400EB-11CP 06.0 PQ: 0 ANSI: 5 [ 22.559624] scsi 1:0:0:0: CD-ROM PIONEER DVD-RW DVR-116D 1.03 PQ: 0 ANSI: 5 [ 22.565591] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 17 [ 22.565614] ohci_hcd 0000:00:03.0: OHCI Host Controller [ 22.565982] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1 [ 22.566016] ohci_hcd 0000:00:03.0: irq 17, io mem 0xe2000000 [ 22.626507] usb usb1: configuration #1 chosen from 1 choice [ 22.626565] hub 1-0:1.0: USB hub found [ 22.626581] hub 1-0:1.0: 3 ports detected [ 22.729142] ACPI: PCI Interrupt 0000:00:03.1[b] -> GSI 21 (level, low) -> IRQ 18 [ 22.729171] ohci_hcd 0000:00:03.1: OHCI Host Controller [ 22.729213] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2 [ 22.729236] ohci_hcd 0000:00:03.1: irq 18, io mem 0xe2001000 [ 22.787028] usb usb2: configuration #1 chosen from 1 choice [ 22.787073] hub 2-0:1.0: USB hub found [ 22.787084] hub 2-0:1.0: 3 ports detected [ 22.888716] ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 19 [ 22.888743] ohci_hcd 0000:00:03.2: OHCI Host Controller [ 22.888785] ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3 [ 22.888816] ohci_hcd 0000:00:03.2: irq 19, io mem 0xe2002000 [ 22.945561] usb usb3: configuration #1 chosen from 1 choice [ 22.945604] hub 3-0:1.0: USB hub found [ 22.945618] hub 3-0:1.0: 2 ports detected [ 23.047457] 8139cp 0000:00:0e.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip [ 23.047465] 8139cp 0000:00:0e.0: Try the "8139too" driver instead. [ 23.050353] ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 20 [ 23.050373] ehci_hcd 0000:00:03.3: EHCI Host Controller [ 23.050422] ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4 [ 23.050466] PCI: cache line size of 128 is not supported by device 0000:00:03.3 [ 23.050480] ehci_hcd 0000:00:03.3: irq 20, io mem 0xe2003000 [ 23.051340] 8139too Fast Ethernet driver 0.9.28 [ 23.060156] ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 23.060366] usb usb4: configuration #1 chosen from 1 choice [ 23.060411] hub 4-0:1.0: USB hub found [ 23.060423] hub 4-0:1.0: 8 ports detected [ 23.164223] ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 18 (level, low) -> IRQ 21 [ 23.165109] eth0: RealTek RTL8139 at 0xe800, 00:01:80:6b:4d:69, IRQ 21 [ 23.165115] eth0: Identified 8139 chip type 'RTL-8100B/8139D' [ 23.186964] Driver 'sd' needs updating - please use bus_type methods [ 23.187136] sd 0:0:0:0: [sda] 320173056 512-byte hardware sectors (163929 MB) [ 23.187165] sd 0:0:0:0: [sda] Write Protect is off [ 23.187170] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 23.187211] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 23.187302] sd 0:0:0:0: [sda] 320173056 512-byte hardware sectors (163929 MB) [ 23.187323] sd 0:0:0:0: [sda] Write Protect is off [ 23.187327] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 23.187364] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 23.187372] sda:<4>Driver 'sr' needs updating - please use bus_type methods [ 23.206292] sda1 sda2 < sda5 sda6 sda7 > [ 23.262517] sd 0:0:0:0: [sda] Attached SCSI disk [ 23.262620] sd 0:0:1:0: [sdb] 78165360 512-byte hardware sectors (40021 MB) [ 23.262655] sd 0:0:1:0: [sdb] Write Protect is off [ 23.262660] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00 [ 23.262700] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 23.262779] sd 0:0:1:0: [sdb] 78165360 512-byte hardware sectors (40021 MB) [ 23.262801] sd 0:0:1:0: [sdb] Write Protect is off [ 23.262806] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00 [ 23.262852] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 23.262859] sdb: sdb1 [ 23.366676] sd 0:0:1:0: [sdb] Attached SCSI disk [ 23.376417] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 23.376459] sd 0:0:1:0: Attached scsi generic sg1 type 0 [ 23.376495] sr 1:0:0:0: Attached scsi generic sg2 type 5 [ 23.411803] sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray [ 23.411812] Uniform CD-ROM driver Revision: 3.20 [ 23.411909] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 23.979093] Attempting manual resume [ 23.979098] swsusp: Resume From Partition 8:7 [ 23.979100] PM: Checking swsusp image. [ 23.993051] PM: Resume from disk failed. [ 24.073571] kjournald starting. Commit interval 5 seconds [ 24.073594] EXT3-fs: mounted filesystem with ordered data mode. [ 31.615833] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 31.647499] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 31.682903] Linux agpgart interface v0.102 [ 31.791153] agpgart: Detected SiS chipset - id:1633 [ 31.808583] agpgart: AGP aperture is 256M @ 0xc0000000 [ 32.183674] input: Power Button (FF) as /devices/virtual/input/input2 [ 32.208954] ACPI: Power Button (FF) [PWRF] [ 32.209107] input: Power Button (CM) as /devices/virtual/input/input3 [ 32.240836] ACPI: Power Button (CM) [PWRB] [ 32.240971] input: Sleep Button (CM) as /devices/virtual/input/input4 [ 32.264776] ACPI: Sleep Button (CM) [FUTS] [ 32.632028] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 33.056364] [fglrx] Maximum main memory to use for locked dma buffers: 1898 MBytes. [ 33.056426] [fglrx] vendor: 1002 device: 7291 count: 1 [ 33.056524] [fglrx] ioport: bar 1, base 0xd000, size: 0x100 [ 33.056554] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 33.057380] [fglrx] Driver built-in PAT support is enabled successfully [ 33.057422] [fglrx] module loaded - fglrx 8.57.2 [Jan 14 2009] with 1 minors [ 33.678545] input: PC Speaker as /devices/platform/pcspkr/input/input5 [ 34.132571] ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 21 [ 34.456446] intel8x0_measure_ac97_clock: measured 55728 usecs [ 34.456452] intel8x0: clocking to 48000 [ 34.485647] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input6 [ 34.546242] parport_pc 00:0a: reported by Plug and Play ACPI [ 34.546325] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA] [ 35.888230] lp0: using parport0 (interrupt-driven). [ 35.959955] Adding 5245180k swap on /dev/sda7. Priority:-1 extents:1 across:5245180k [ 36.529814] EXT3 FS on sda6, internal journal [ 36.730620] device-mapper: uevent: version 1.0.3 [ 36.730677] device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: [email protected] [ 37.619699] kjournald starting. Commit interval 5 seconds [ 37.623858] EXT3 FS on sdb1, internal journal [ 37.623865] EXT3-fs: mounted filesystem with ordered data mode. [ 38.162794] ip_tables: (C) 2000-2006 Netfilter Core Team
オフライン
2007年10月11日以降の投稿は、クリエイティブ・コモンズ-表示-継承-3.0 (Cc-by-sa-3.0)で提供されます。
著作権等の他者の権利を不当に侵害するような投稿、特定の個人や団体などへの誹謗中傷を含む投稿、個人情報を含む投稿など、違法性のある投稿は行わないでください。
Ubuntu and Canonical are registered trademarks of Canonical Ltd.