Ubuntu日本語フォーラム

iwamura1041 · 2010-11-07 17:31:35

はじめまして。Linux初心者です。
Ubuntu 10.10 Netbook Editionをインストールして使っていますが、無線LANが非常に不安定でつかいものになりません。
無線LANはFRNU５０３内臓の「IEEE802.11 b/g対応」ですが、このLANでは接続できないのでしょうか？
MACやWindowsでは正常に接続できているので、ubuntuのせいだと思っています。

状態としては、「NetworkManager」で接続していますが、数分おきに接続が途切れ、つながったりつながらなかったりをくりかえしています。他のOSがはいったPC〔MAC　OSX　WindowsXP〕では正常に接続でき、途切れることはありません。

過去のスレッドも読んで試したり、検索もかけましたが、つながらない状況が続いています。
詳しい方助けてください。

tista · 2010-11-07 18:23:08

iwamura1041様

とりあえず下記のコマンドを「端末」から実行して出力結果を投稿して頂けますか？
（メニュー→アクセサリ→端末と辿って起動して下さい。）

コード:

sudo lshw -short | grep network

無線LANはFRNU５０３内臓の「IEEE802.11 b/g対応」ですが、このLANでは接続できないのでしょうか？

これだけではご使用の無線LANチップがわからないので上記コマンドの出力結果を見たいのです。

iwamura1041 · 2010-11-07 18:40:27

tista様

ご指導ありがとうございます。
早速ですが、sudo lshw -short | grep networkの結果です。

$ sudo lshw -short | grep network
PCI (sysfs)
/0/100/1c.1/0 eth0 network RTL8101E/RTL8102E PCI Express Fast Ethernet controller
/1 wlan0 network Wireless interface

Linuxは、本当に初めてで右も左もわからないのでよろしくお願いします。

tista · 2010-11-07 19:32:24

ご投稿ありがとう御座います。

上記結果から、2行目：

/1 wlan0 network Wireless interface

が無線LANデバイスに当たると推測できます。

しかし、詳細なチップ情報を得られていないため、適正なドライバが適応されていない可能性が高いでしょう。

ひとつご確認なのですが、メニュー→設定？ or システム管理？の中に「ハードウェアドライバ」というエントリがありますでしょうか？
ありましたらそれをクリックして頂くとウィンドウが起動し、お使いのハードウェアに適合する追加ドライバを検索してしてくれます。
まずはこれで無線LANドライバがヒットするか試してみて下さい。
ヒットしたならそのままインストールまで可能ですので、インストールして下さい。

ヒットしない場合、ちょっと面倒な手順を踏む必要があります。

iwamura1041 · 2010-11-07 19:40:28

tista様

ハードウェアドライバはありませんでしたが、追加のドライバがそれにあたると思います。
検索しましたが、ヒットしませんでした。

すいませんが、面倒な手順をご指導いただきましてもよろしいでしょうか？
このままですと、すごい不便ですのでよければ助けてください。

tista · 2010-11-07 20:41:57

では、下記のコマンドの出力結果を投稿して頂きたいのですが、注意が一点。
ともに行数が多く行も長いので、投稿する際のそれぞれの出力結果を

コード:

というタグでくくって下さい。そうするとページ内スクロールが効いて読みやすくなりますし、紙面を圧迫しないで済みます。

では、1つめ：

コード:

lspci

2つめ：

コード:

dmesg

また、投稿されたこれらを当方が読むのに時間がかかりますので、ご了承下さい。

tista · 2010-11-07 20:47:19

すいません。タグはこうです。

[ｃｏｄｅ]

[／ｃｏｄｅ]

※全角のところは半角に直して使って下さい。

iwamura1041 · 2010-11-07 21:00:44

ご丁寧に説明していただきありがとうございます。

早速ですが、lspciの結果です。

コード:

00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02)
00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02)
00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02)

次に、dmesgの結果です。

コード:

[    0.200234] ACPI: (supports S0 S3 S4 S5)
[    0.200313] ACPI: Using IOAPIC for interrupt routing
[    0.215617] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[    0.216274] ACPI: No dock devices found.
[    0.216287] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.218054] ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[    0.218076] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f701fdc8), AE_ALREADY_EXISTS
[    0.218099] ACPI: Marking method _OSC as Serialized because of AE_ALREADY_EXISTS error
[    0.218164] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.221162] pci_root PNP0A08:00: host bridge window [io  0x0000-0x0cf7]
[    0.221175] pci_root PNP0A08:00: host bridge window [io  0x0d00-0xffff]
[    0.221186] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[    0.221201] pci_root PNP0A08:00: host bridge window [mem 0x40000000-0xfebfffff]
[    0.221325] pci 0000:00:02.0: reg 10: [mem 0x54280000-0x542fffff]
[    0.221338] pci 0000:00:02.0: reg 14: [io  0x40c0-0x40c7]
[    0.221350] pci 0000:00:02.0: reg 18: [mem 0x40000000-0x4fffffff pref]
[    0.221362] pci 0000:00:02.0: reg 1c: [mem 0x54300000-0x5433ffff]
[    0.221430] pci 0000:00:02.1: reg 10: [mem 0x54200000-0x5427ffff]
[    0.221587] pci 0000:00:1b.0: reg 10: [mem 0x54340000-0x54343fff 64bit]
[    0.221671] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.221682] pci 0000:00:1b.0: PME# disabled
[    0.221819] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.221830] pci 0000:00:1c.0: PME# disabled
[    0.221970] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.221982] pci 0000:00:1c.1: PME# disabled
[    0.222090] pci 0000:00:1d.0: reg 20: [io  0x4080-0x409f]
[    0.222195] pci 0000:00:1d.1: reg 20: [io  0x4060-0x407f]
[    0.222298] pci 0000:00:1d.2: reg 20: [io  0x4040-0x405f]
[    0.222397] pci 0000:00:1d.3: reg 20: [io  0x4020-0x403f]
[    0.222488] pci 0000:00:1d.7: reg 10: [mem 0x54344400-0x543447ff]
[    0.222573] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.222585] pci 0000:00:1d.7: PME# disabled
[    0.222808] pci 0000:00:1f.0: quirk: [io  0x0400-0x047f] claimed by ICH6 ACPI/GPIO/TCO
[    0.222821] pci 0000:00:1f.0: quirk: [io  0x0500-0x053f] claimed by ICH6 GPIO
[    0.222839] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 4 PIO at 0068 (mask 0007)
[    0.222935] pci 0000:00:1f.2: reg 10: [io  0x0000-0x0007]
[    0.222951] pci 0000:00:1f.2: reg 14: [io  0x0000-0x0003]
[    0.222966] pci 0000:00:1f.2: reg 18: [io  0x0000-0x0007]
[    0.222983] pci 0000:00:1f.2: reg 1c: [io  0x0000-0x0003]
[    0.222999] pci 0000:00:1f.2: reg 20: [io  0x40a0-0x40af]
[    0.223055] pci 0000:00:1f.2: PME# supported from D3hot
[    0.223067] pci 0000:00:1f.2: PME# disabled
[    0.223159] pci 0000:00:1f.3: reg 20: [io  0x4000-0x401f]
[    0.223301] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[    0.223315] pci 0000:00:1c.0:   bridge window [io  0x3000-0x3fff]
[    0.223329] pci 0000:00:1c.0:   bridge window [mem 0x53100000-0x541fffff]
[    0.223347] pci 0000:00:1c.0:   bridge window [mem 0x50000000-0x50ffffff 64bit pref]
[    0.223496] pci 0000:02:00.0: reg 10: [io  0x1000-0x10ff]
[    0.223538] pci 0000:02:00.0: reg 18: [mem 0x51010000-0x51010fff 64bit pref]
[    0.223570] pci 0000:02:00.0: reg 20: [mem 0x51000000-0x5100ffff 64bit pref]
[    0.223592] pci 0000:02:00.0: reg 30: [mem 0xffff0000-0xffffffff pref]
[    0.223669] pci 0000:02:00.0: supports D1 D2
[    0.223678] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.223691] pci 0000:02:00.0: PME# disabled
[    0.228078] pci 0000:00:1c.1: PCI bridge to [bus 02-02]
[    0.228095] pci 0000:00:1c.1:   bridge window [io  0x1000-0x2fff]
[    0.228108] pci 0000:00:1c.1:   bridge window [mem 0x52100000-0x530fffff]
[    0.228125] pci 0000:00:1c.1:   bridge window [mem 0x51000000-0x520fffff 64bit pref]
[    0.228259] pci 0000:00:1e.0: PCI bridge to [bus 03-03] (subtractive decode)
[    0.228272] pci 0000:00:1e.0:   bridge window [io  0xf000-0x0000] (disabled)
[    0.228285] pci 0000:00:1e.0:   bridge window [mem 0xfff00000-0x000fffff] (disabled)
[    0.228301] pci 0000:00:1e.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.228312] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.228321] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.228330] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.228340] pci 0000:00:1e.0:   bridge window [mem 0x40000000-0xfebfffff] (subtractive decode)
[    0.228375] pci_bus 0000:00: on NUMA node 0
[    0.228398] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.228974] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
[    0.229424] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
[    0.229750] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
[    0.230332] ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[    0.230354] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f701fdc8), AE_ALREADY_EXISTS
[    0.247419] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
[    0.247747] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12)
[    0.248088] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
[    0.248410] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
[    0.248729] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[    0.249040] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[    0.249364] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[    0.249680] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[    0.249846] HEST: Table is not found!
[    0.250124] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.250153] vgaarb: loaded
[    0.250771] SCSI subsystem initialized
[    0.251031] libata version 3.00 loaded.
[    0.251255] usbcore: registered new interface driver usbfs
[    0.251311] usbcore: registered new interface driver hub
[    0.251407] usbcore: registered new device driver usb
[    0.251903] ACPI: WMI: Mapper loaded
[    0.251910] PCI: Using ACPI for IRQ routing
[    0.251920] PCI: pci_cache_line_size set to 64 bytes
[    0.252105] reserve RAM buffer: 0000000000002000 - 000000000000ffff 
[    0.252116] reserve RAM buffer: 000000000009fc00 - 000000000009ffff 
[    0.252125] reserve RAM buffer: 000000003f376000 - 000000003fffffff 
[    0.252462] NetLabel: Initializing
[    0.252469] NetLabel:  domain hash size = 128
[    0.252474] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.252511] NetLabel:  unlabeled traffic allowed by default
[    0.252628] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.252643] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.252658] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.256290] Switching to clocksource tsc
[    0.285751] AppArmor: AppArmor Filesystem Enabled
[    0.285792] pnp: PnP ACPI init
[    0.285841] ACPI: bus type pnp registered
[    0.290704] pnp: PnP ACPI: found 9 devices
[    0.290713] ACPI: ACPI bus type pnp unregistered
[    0.290725] PnPBIOS: Disabled by ACPI PNP
[    0.290762] system 00:01: [io  0x0200-0x020f] has been reserved
[    0.290774] system 00:01: [io  0x0600-0x060f] has been reserved
[    0.290783] system 00:01: [io  0x0610] has been reserved
[    0.290792] system 00:01: [io  0x0800-0x080f] has been reserved
[    0.290802] system 00:01: [io  0x0400-0x047f] has been reserved
[    0.290811] system 00:01: [io  0x0500-0x053f] has been reserved
[    0.290825] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved
[    0.290835] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.290845] system 00:01: [mem 0xfed14000-0xfed17fff] has been reserved
[    0.290855] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.290865] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.290876] system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.290887] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.331478] pci 0000:02:00.0: no compatible bridge window for [mem 0xffff0000-0xffffffff pref]
[    0.331572] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[    0.331586] pci 0000:00:1c.0:   bridge window [io  0x3000-0x3fff]
[    0.331602] pci 0000:00:1c.0:   bridge window [mem 0x53100000-0x541fffff]
[    0.331615] pci 0000:00:1c.0:   bridge window [mem 0x50000000-0x50ffffff 64bit pref]
[    0.331641] pci 0000:02:00.0: BAR 6: assigned [mem 0x51020000-0x5102ffff pref]
[    0.331651] pci 0000:00:1c.1: PCI bridge to [bus 02-02]
[    0.331661] pci 0000:00:1c.1:   bridge window [io  0x1000-0x2fff]
[    0.331674] pci 0000:00:1c.1:   bridge window [mem 0x52100000-0x530fffff]
[    0.331687] pci 0000:00:1c.1:   bridge window [mem 0x51000000-0x520fffff 64bit pref]
[    0.331704] pci 0000:00:1e.0: PCI bridge to [bus 03-03]
[    0.331710] pci 0000:00:1e.0:   bridge window [io  disabled]
[    0.331722] pci 0000:00:1e.0:   bridge window [mem disabled]
[    0.331732] pci 0000:00:1e.0:   bridge window [mem pref disabled]
[    0.331781]   alloc irq_desc for 16 on node -1
[    0.331788]   alloc kstat_irqs on node -1
[    0.331807] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.331820] pci 0000:00:1c.0: setting latency timer to 64
[    0.331843]   alloc irq_desc for 17 on node -1
[    0.331849]   alloc kstat_irqs on node -1
[    0.331861] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    0.331873] pci 0000:00:1c.1: setting latency timer to 64
[    0.331891] pci 0000:00:1e.0: setting latency timer to 64
[    0.331904] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.331912] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.331921] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.331930] pci_bus 0000:00: resource 7 [mem 0x40000000-0xfebfffff]
[    0.331939] pci_bus 0000:01: resource 0 [io  0x3000-0x3fff]
[    0.331947] pci_bus 0000:01: resource 1 [mem 0x53100000-0x541fffff]
[    0.331956] pci_bus 0000:01: resource 2 [mem 0x50000000-0x50ffffff 64bit pref]
[    0.331966] pci_bus 0000:02: resource 0 [io  0x1000-0x2fff]
[    0.331974] pci_bus 0000:02: resource 1 [mem 0x52100000-0x530fffff]
[    0.331983] pci_bus 0000:02: resource 2 [mem 0x51000000-0x520fffff 64bit pref]
[    0.331993] pci_bus 0000:03: resource 4 [io  0x0000-0x0cf7]
[    0.332001] pci_bus 0000:03: resource 5 [io  0x0d00-0xffff]
[    0.332010] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]
[    0.332018] pci_bus 0000:03: resource 7 [mem 0x40000000-0xfebfffff]
[    0.332131] NET: Registered protocol family 2
[    0.332327] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.333206] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.334331] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.334992] TCP: Hash tables configured (established 131072 bind 65536)
[    0.335007] TCP reno registered
[    0.335025] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.335054] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.335339] NET: Registered protocol family 1
[    0.335401] pci 0000:00:02.0: Boot video device
[    0.335740] PCI: CLS 0 bytes, default 64
[    0.335817] Simple Boot Flag value 0x5 read from CMOS RAM was invalid
[    0.335825] Simple Boot Flag at 0x44 set to 0x1
[    0.336437] cpufreq-nforce2: No nForce2 chipset.
[    0.336544] Scanning for low memory corruption every 60 seconds
[    0.337036] audit: initializing netlink socket (disabled)
[    0.337066] type=2000 audit(1289130738.332:1): initialized
[    0.361260] highmem bounce pool size: 64 pages
[    0.361279] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.366810] VFS: Disk quotas dquot_6.5.2
[    0.367036] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.369299] fuse init (API version 7.14)
[    0.369658] msgmni has been set to 1708
[    0.398290] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.398301] io scheduler noop registered
[    0.398308] io scheduler deadline registered
[    0.398369] io scheduler cfq registered (default)
[    0.398704] pcieport 0000:00:1c.0: setting latency timer to 64
[    0.398775]   alloc irq_desc for 40 on node -1
[    0.398782]   alloc kstat_irqs on node -1
[    0.398807] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
[    0.399071] pcieport 0000:00:1c.1: setting latency timer to 64
[    0.399135]   alloc irq_desc for 41 on node -1
[    0.399141]   alloc kstat_irqs on node -1
[    0.399160] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X
[    0.399486] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.399841] ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[    0.399862] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f701fdc8), AE_ALREADY_EXISTS
[    0.400210] ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[    0.400229] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f701fdc8), AE_ALREADY_EXISTS
[    0.400639] ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[    0.400660] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f701fdc8), AE_ALREADY_EXISTS
[    0.400992] ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS
[    0.401011] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f701fdc8), AE_ALREADY_EXISTS
[    0.401131] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.401476] intel_idle: MWAIT substates: 0x20220
[    0.401484] intel_idle: v0.4 model 0x1C
[    0.401490] intel_idle: lapic_timer_reliable_states 0x6
[    0.401511] Marking TSC unstable due to TSC halts in idle states deeper than C2
[    0.401889] Switching to clocksource hpet
[    0.402519] ACPI: AC Adapter [ACAD] (on-line)
[    0.402797] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[    0.402814] ACPI: Power Button [PWRB]
[    0.402973] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
[    0.403471] ACPI: Lid Switch [LID0]
[    0.403716] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[    0.403734] ACPI: Sleep Button [SLPB]
[    0.403930] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    0.403943] ACPI: Power Button [PWRF]
[    0.404703] ACPI: acpi_idle yielding to intel_idle
[    0.410065] thermal LNXTHERM:01: registered as thermal_zone0
[    0.410099] ACPI: Thermal Zone [THRM] (55 C)
[    0.410390] ERST: Table is not found!
[    0.411155] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.416132] brd: module loaded
[    0.417244] ACPI: Battery Slot [BAT1] (battery absent)
[    0.417290] isapnp: Scanning for PnP cards...
[    0.467686] loop: module loaded
[    0.468412] ata_piix 0000:00:1f.2: version 2.13
[    0.468454] ata_piix 0000:00:1f.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    0.468468] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[    0.468556] ata_piix 0000:00:1f.2: setting latency timer to 64
[    0.512327] scsi0 : ata_piix
[    0.556330] scsi1 : ata_piix
[    0.559396] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x40a0 irq 14
[    0.559408] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x40a8 irq 15
[    0.560878] Fixed MDIO Bus: probed
[    0.561053] PPP generic driver version 2.4.2
[    0.561257] tun: Universal TUN/TAP device driver, 1.6
[    0.561265] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[    0.561543] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.561609] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.561653] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    0.561664] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    0.561780] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    0.561833] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[    0.561855] ehci_hcd 0000:00:1d.7: debug port 1
[    0.565757] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[    0.565820] ehci_hcd 0000:00:1d.7: irq 16, io mem 0x54344400
[    0.600628] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    0.601070] hub 1-0:1.0: USB hub found
[    0.601087] hub 1-0:1.0: 8 ports detected
[    0.601295] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.601348] uhci_hcd: USB Universal Host Controller Interface driver
[    0.601438] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.601456] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    0.601467] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    0.601592] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    0.601643] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00004080
[    0.602016] hub 2-0:1.0: USB hub found
[    0.602030] hub 2-0:1.0: 2 ports detected
[    0.602183] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    0.602201] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    0.602210] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    0.602326] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    0.602402] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00004060
[    0.602770] hub 3-0:1.0: USB hub found
[    0.602784] hub 3-0:1.0: 2 ports detected
[    0.602937]   alloc irq_desc for 18 on node -1
[    0.602944]   alloc kstat_irqs on node -1
[    0.602961] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    0.602977] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    0.602986] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    0.603096] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    0.603162] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00004040
[    0.603529] hub 4-0:1.0: USB hub found
[    0.603542] hub 4-0:1.0: 2 ports detected
[    0.603685]   alloc irq_desc for 19 on node -1
[    0.603692]   alloc kstat_irqs on node -1
[    0.603705] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    0.603721] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    0.603730] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    0.603839] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    0.603903] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00004020
[    0.604315] hub 5-0:1.0: USB hub found
[    0.604329] hub 5-0:1.0: 2 ports detected
[    0.604644] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOUE] at 0x60,0x64 irq 1,12
[    0.605457] i8042.c: Warning: Keylock active.
[    0.614390] i8042.c: Detected active multiplexing controller, rev 1.1.
[    0.619490] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.619508] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    0.619613] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    0.619698] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    0.619788] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    0.620213] mice: PS/2 mouse device common for all mice
[    0.620749] rtc_cmos 00:03: RTC can wake from S4
[    0.620880] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    0.620936] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[    0.621323] device-mapper: uevent: version 1.0.3
[    0.621669] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: [email protected]
[    0.621885] device-mapper: multipath: version 1.1.1 loaded
[    0.621893] device-mapper: multipath round-robin: version 1.0.0 loaded
[    0.622305] EISA: Probing bus 0 at eisa.0
[    0.622314] EISA: Cannot allocate resource for mainboard
[    0.622323] Cannot allocate resource for EISA slot 1
[    0.622331] Cannot allocate resource for EISA slot 2
[    0.622338] Cannot allocate resource for EISA slot 3
[    0.622346] Cannot allocate resource for EISA slot 4
[    0.622354] Cannot allocate resource for EISA slot 5
[    0.622362] Cannot allocate resource for EISA slot 6
[    0.622370] Cannot allocate resource for EISA slot 7
[    0.622378] Cannot allocate resource for EISA slot 8
[    0.622384] EISA: Detected 0 cards.
[    0.622859] cpuidle: using governor ladder
[    0.623260] cpuidle: using governor menu
[    0.624183] TCP cubic registered
[    0.624635] NET: Registered protocol family 10
[    0.625673] lo: Disabled Privacy Extensions
[    0.626335] NET: Registered protocol family 17
[    0.627567] Using IPI No-Shortcut mode
[    0.627858] PM: Resume from disk failed.
[    0.627888] registered taskstats version 1
[    0.628402]   Magic number: 2:62:883
[    0.628552] rtc_cmos 00:03: setting system clock to 2010-11-07 11:52:19 UTC (1289130739)
[    0.628562] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.628567] EDD information not available.
[    0.644736] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[    0.720493] ata1.00: ATA-8: FUJITSU MHZ2160BH G2, 00000009, max UDMA/100
[    0.720504] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    0.737166] ata1.00: configured for UDMA/100
[    0.787809] isapnp: No Plug & Play device found
[    0.788219] scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MHZ2160B 0000 PQ: 0 ANSI: 5
[    0.788721] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    0.789053] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[    0.789286] sd 0:0:0:0: [sda] Write Protect is off
[    0.789297] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    0.789396] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.789983]  sda: sda1 sda2 < sda5 >
[    0.810876] sd 0:0:0:0: [sda] Attached SCSI disk
[    0.856585] Freeing initrd memory: 10516k freed
[    0.867501] Freeing unused kernel memory: 684k freed
[    0.868377] Write protecting the kernel text: 4932k
[    0.868455] Write protecting the kernel read-only data: 1976k
[    0.910594] udev[80]: starting version 163
[    0.969140] usb 1-5: new high speed USB device using ehci_hcd and address 3
[    1.218731] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    1.218792] r8169 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    1.218874] r8169 0000:02:00.0: setting latency timer to 64
[    1.218956]   alloc irq_desc for 42 on node -1
[    1.218963]   alloc kstat_irqs on node -1
[    1.218993] r8169 0000:02:00.0: irq 42 for MSI/MSI-X
[    1.248257] usb 1-7: new high speed USB device using ehci_hcd and address 4
[    1.273312] r8169 0000:02:00.0: eth0: RTL8102e at 0xf8022000, 00:23:8b:62:04:2f, XID 04a00000 IRQ 42
[    1.383037] EXT4-fs (sda1): INFO: recovery required on readonly filesystem
[    1.383048] EXT4-fs (sda1): write access will be enabled during recovery
[    1.632114] usb 2-1: new low speed USB device using uhci_hcd and address 2
[    1.850559] usbcore: registered new interface driver hiddev
[    1.867570] input:  I-Rocks Technology Co., LTD. Laser Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.0/input/input5
[    1.868020] generic-usb 0003:14A5:2003.0001: input,hidraw0: USB HID v1.11 Mouse [ I-Rocks Technology Co., LTD. Laser Mouse] on usb-0000:00:1d.0-1/input0
[    1.868134] usbcore: registered new interface driver usbhid
[    1.868141] usbhid: USB HID core driver
[    4.861950] EXT4-fs (sda1): orphan cleanup on readonly fs
[    4.861982] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6820069
[    4.862131] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6820039
[    4.862178] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7340074
[    4.862224] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7340073
[    4.862265] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7340072
[    4.862322] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6816091
[    4.862362] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6816086
[    4.862401] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6816085
[    4.862499] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6815781
[    4.862542] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6815990
[    4.862585] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 6816145
[    4.862622] EXT4-fs (sda1): 11 orphan inodes deleted
[    4.862630] EXT4-fs (sda1): recovery complete
[    5.436214] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[   16.395873] Adding 3068924k swap on /dev/sda5.  Priority:-1 extents:1 across:3068924k 
[   16.419282] udev[327]: starting version 163
[   16.509439] lp: driver loaded but no devices found
[   16.631500] intel_rng: FWH not detected
[   16.923447] leds_ss4200: no LED devices found
[   17.008838] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input6
[   17.009016] ACPI: Video Device [OVGA] (multi-head: yes  rom: yes  post: no)
[   17.026196] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[   17.081068] Linux agpgart interface v0.103
[   17.357509] agpgart-intel 0000:00:00.0: Intel 945GME Chipset
[   17.358047] agpgart-intel 0000:00:00.0: detected 7932K stolen memory
[   17.392587] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x40000000
[   17.394035] Linux video capture interface: v2.00
[   17.447460] uvcvideo: Found UVC 1.00 device USB 2.0 Camera (064e:a102)
[   17.565617] input: USB 2.0 Camera as /devices/pci0000:00/0000:00:1d.7/usb1/1-5/1-5:1.0/input/input7
[   17.565852] usbcore: registered new interface driver uvcvideo
[   17.565859] USB Video Class driver (v0.1.0)
[   17.715483] type=1400 audit(1289130756.582:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient3" pid=585 comm="apparmor_parser"
[   17.716513] type=1400 audit(1289130756.586:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=585 comm="apparmor_parser"
[   17.717042] type=1400 audit(1289130756.586:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=585 comm="apparmor_parser"
[   17.721422] cfg80211: Calling CRDA to update world regulatory domain
[   17.780930] cfg80211: World regulatory domain updated:
[   17.780941]     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   17.780952]     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   17.780962]     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   17.780972]     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   17.780982]     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   17.780991]     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   17.836681] [drm] Initialized drm 1.1.0 20060810
[   18.151365] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04771/0xa40000/0xa0000
[   18.205858] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input8
[   18.281359] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   18.281375] i915 0000:00:02.0: setting latency timer to 64
[   18.483275] type=1400 audit(1289130757.350:5): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=762 comm="apparmor_parser"
[   18.485406] type=1400 audit(1289130757.354:6): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient3" pid=763 comm="apparmor_parser"
[   18.486277] type=1400 audit(1289130757.354:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=763 comm="apparmor_parser"
[   18.486797] type=1400 audit(1289130757.354:8): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=763 comm="apparmor_parser"
[   18.507226] type=1400 audit(1289130757.374:9): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=766 comm="apparmor_parser"
[   18.545804] type=1400 audit(1289130757.414:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=772 comm="apparmor_parser"
[   18.547048] type=1400 audit(1289130757.414:11): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=772 comm="apparmor_parser"
[   18.550771] mtrr: no more MTRRs available
[   18.550782] [drm] MTRR allocation failed.  Graphics performance may suffer.
[   18.565454] [drm] set up 7M of stolen space
[   18.589526] r8169 0000:02:00.0: eth0: link down
[   18.590175] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   18.702660] phy0: Selected rate control algorithm 'minstrel'
[   18.706452] phy0: hwaddr 00:17:c4:68:8a:28, RTL8187BvE V0 + rtl8225z2, rfkill mask 2
[   18.735071] rtl8187: Customer ID is 0x00
[   18.735218] Registered led device: rtl8187-phy0::radio
[   18.735305] Registered led device: rtl8187-phy0::tx
[   18.735380] Registered led device: rtl8187-phy0::rx
[   18.739308] rtl8187: wireless switch is on
[   18.739430] usbcore: registered new interface driver rtl8187
[   18.827942] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[   18.828560] [drm] initialized overlay support
[   19.141111] Skipping EDID probe due to cached edid
[   19.571989] Console: switching to colour frame buffer device 128x36
[   19.579671] fb0: inteldrmfb frame buffer device
[   19.579678] drm: registered panic notifier
[   19.579687] Slow work thread pool: Starting up
[   19.579830] Slow work thread pool: Ready
[   19.579851] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[   19.579972] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   19.580116]   alloc irq_desc for 43 on node -1
[   19.580124]   alloc kstat_irqs on node -1
[   19.580180] HDA Intel 0000:00:1b.0: irq 43 for MSI/MSI-X
[   19.580251] HDA Intel 0000:00:1b.0: setting latency timer to 64
[   19.669367] hda_codec: ALC268: BIOS auto-probing.
[   19.700143] Skipping EDID probe due to cached edid
[   19.876487] ppdev: user-space parallel port driver
[   20.293294] Skipping EDID probe due to cached edid
[   20.324236] Skipping EDID probe due to cached edid
[   22.398595] Skipping EDID probe due to cached edid
[   22.437152] Skipping EDID probe due to cached edid
[   22.473197] Skipping EDID probe due to cached edid
[   22.512199] Skipping EDID probe due to cached edid
[   23.101980] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   25.331684] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[   29.670394] wlan0: authenticate with 00:0a:79:96:65:5f (try 1)
[   29.672638] wlan0: authenticated
[   29.751273] wlan0: associate with 00:0a:79:96:65:5f (try 1)
[   29.772156] Skipping EDID probe due to cached edid
[   29.835147] wlan0: RX AssocResp from 00:0a:79:96:65:5f (capab=0x401 status=0 aid=1)
[   29.835161] wlan0: associated
[   29.930093] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   29.930252] cfg80211: Calling CRDA for country: JP
[   29.957777] cfg80211: Received country IE:
[   29.957789] cfg80211: Regulatory domain: JP
[   29.957796]     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   29.957807]     (2402000 KHz - 2482000 KHz @ 40000 KHz), (10000 mBi, 1600 mBm)
[   29.957814] cfg80211: CRDA thinks this should applied:
[   29.957820] cfg80211: Regulatory domain: JP
[   29.957826]     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   29.957836]     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   29.957845]     (2457000 KHz - 2482000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[   29.957854]     (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[   29.957862]     (4910000 KHz - 4930000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   29.957871]     (4910000 KHz - 4990000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[   29.957880]     (4930000 KHz - 4950000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   29.957889]     (5030000 KHz - 5045000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   29.957897]     (5030000 KHz - 5090000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[   29.957906]     (5050000 KHz - 5060000 KHz @ 10000 KHz), (N/A, 2300 mBm)
[   29.957915]     (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   29.957924]     (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   29.957933]     (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2300 mBm)
[   29.957940] cfg80211: We intersect both of these and get:
[   29.957946] cfg80211: Regulatory domain: 98
[   29.957952]     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   29.957962]     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 1600 mBm)
[   29.957971]     (2457000 KHz - 2482000 KHz @ 20000 KHz), (N/A, 1600 mBm)
[   29.957980]     (2474000 KHz - 2482000 KHz @ 8000 KHz), (N/A, 1600 mBm)
[   29.957997] cfg80211: Disabling channel 2484 MHz on phy0 due to Country IE
[   29.958008] cfg80211: Current regulatory domain updated by AP to: JP
[   29.958015]     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   29.958024]     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 1600 mBm)
[   29.958033]     (2457000 KHz - 2482000 KHz @ 20000 KHz), (N/A, 1600 mBm)
[   29.958042]     (2474000 KHz - 2482000 KHz @ 8000 KHz), (N/A, 1600 mBm)
[   40.802688] wlan0: no IPv6 routers present

思ったよりも出力されてきて驚きました。
面倒そうで申し訳ございませんがよろしくお願いします。

tista · 2010-11-07 21:12:17

何度も投稿頂いて申し訳ないです。

dmesgから、

コード:

[   18.739308] rtl8187: wireless switch is on

が多分無線LANチップでしょう。これからこれに対するworkaroundを検索に行きますので、もう暫くお待ちを・・・。

iwamura1041 · 2010-11-07 21:14:15

ありがとうございます。
何もせずお任せしてしまってすいませんがよろしくお願いします。

tista · 2010-11-08 01:28:04

お時間頂いて申し訳ないです。

実は色々と案を考えたのですが、ビギナの方にいきなりkernel moduleをビルドさせるのも酷なので、
以下のURLに当方がビルドしたkernel moduleをupしておきました。
rtl8187 for Maverick kernel 2.6.35-22

PASSはtistaとして下さい（混雑の多いUploaderなんで気長に・・）。

無事にDL出来ましたら、いよいよ作業開始です。

1. DLしたr8187l.koを当該ディレクトリへコピーします（ホームディレクトリ以下の"ダウンロード"ディレクトリに保存した場合）。
　

コード:

sudo cp $HOME/ダウンロード/r8187l.ko /lib/modules/2.6.35-22-generic/kernel/drivers/net/wireless/rtl818x

2. 既存のrtl8187 kernel moduleを利用しないよう設定します（sudoと同じパスワードが必要です）。
　

コード:

gksu gedit /etc/modprobe.d/blacklist.conf

　としてエディタを開き、最終行へ以下のように追記します。
　

コード:

　blacklist rtl8187
　blacklist rtl8180

3. 新規に導入したr8187l kernel moduleを利用するよう設定します。
　

コード:

sudo depmod -a

　特にErrorもなく終了できたら起動時に利用できるように/etc/modulesへ追記します。
　

コード:

gksu gedit /etc/modules

　としてまたエディタを管理権限で開き、最終行へ
　

コード:

r8187l

　を追記します。

4. 再起動します。

これで正常に起動しましたら下記のコマンドで確認します。

コード:

sudo lshw -short | grep network

では、まずはこの手順でご確認下さい。

einundzwanzighundertsechs · 2010-11-08 02:20:29

tista さんによる投稿:
実は色々と案を考えたのですが、ビギナの方にいきなりkernel moduleをビルドさせるのも酷なので、
以下のURLに当方がビルドしたkernel moduleをupしておきました。

失礼ながら，他人からもらうプログラムには注意が，特にカーネル関係には警戒が必要です．
「誰がコンパイルしたのか分からないようなカーネル（モジュール）は使わない」
というのがセキュリティの基本だと思います．

iwamura1041 · 2010-11-08 02:23:14

遅い時間までありがとうございます。
早速手順を踏んでみました。

sudo lshw -short | grep networkの結果ですが
0/100/1c.1/0 eth0 network RTL8101E/RTL8102E PCI Express Fast Ethernet controller
/1 wlan0 network Wireless interface
で変わらずです。エラー等一切ありませんでした。

私の手順が違うのでしょうか？
遅くまでお付き合いいただきありがとうございます。

tista · 2010-11-08 02:52:59

einundzwanzighundertsechs様

仰る通りです。
では、今回の件なら、einundzwanzighundertsechs様はどのようなworkaroundが最も適切だとお考えでしょうか。

kmz · 2010-11-11 11:04:46

情報をオープンにするという意味では、まずはtistaさんの当てられたパッチの内容を投稿されるのはどうでしょうか。

tista · 2010-11-11 13:20:47

kmz様

ご提案ありがとう御座います。
今回のkernel moduleへは一切のpatchを当ててはおりません。
patchを適用する前にRealtek社のドライバページで配布されているものをそのまま当方の環境でbuildしたものです。

結果はどうであれ、今回の件は手技自体に問題があると思われますので、iwamura1041様へ以前の状態へ復元するよう指示致します。

iwamura1041様

ご連絡が遅れまして申し訳御座いませんでした。
上記のように、tistaのすべての指示を取り消させて頂きたいと思います。
ご迷惑をお掛けいたしまして重ねてお詫び申し上げます。

つきましては、当該のkernel moduleを削除し、元の状態へ復元したいと存じます。

1. 当方がbuildしたr8187lを削除します。
　

コード:

sudo rm -f /lib/modules/2.6.35-22-generic/kernel/drivers/net/wireless/rtl818x/r8187l.ko

2. blacklistを解除します。
　

コード:

gksu gedit /etc/modprobe.d/blacklist.conf

　にて追記した二行を消して下さい。

3. module指定を解除します。
　

コード:

gksu gedit /etc/modules

　にて追記した一行を消して下さい。

3. depmodを実行します。
　

コード:

sudo depmod -a

4. 再起動します。

これで元の状態へ復元して下さい。

Ubuntu日本語フォーラム

お知らせ

#1 2010-11-07 17:31:35

Ubuntu 10.10 Netbook Edition IEEE802.11 b/g

#2 2010-11-07 18:23:08

Re: Ubuntu 10.10 Netbook Edition IEEE802.11 b/g

コード:

#3 2010-11-07 18:40:27

Re: Ubuntu 10.10 Netbook Edition IEEE802.11 b/g

#4 2010-11-07 19:32:24

Re: Ubuntu 10.10 Netbook Edition IEEE802.11 b/g

#5 2010-11-07 19:40:28

Re: Ubuntu 10.10 Netbook Edition IEEE802.11 b/g

#6 2010-11-07 20:41:57

Re: Ubuntu 10.10 Netbook Edition IEEE802.11 b/g

コード:

コード:

コード:

#7 2010-11-07 20:47:19

Re: Ubuntu 10.10 Netbook Edition IEEE802.11 b/g

#8 2010-11-07 21:00:44

Re: Ubuntu 10.10 Netbook Edition IEEE802.11 b/g

コード:

コード:

#9 2010-11-07 21:12:17

Re: Ubuntu 10.10 Netbook Edition IEEE802.11 b/g

コード:

#10 2010-11-07 21:14:15

Re: Ubuntu 10.10 Netbook Edition IEEE802.11 b/g

#11 2010-11-08 01:28:04

Re: Ubuntu 10.10 Netbook Edition IEEE802.11 b/g

コード:

コード:

コード:

コード:

コード:

コード:

コード:

#12 2010-11-08 02:20:29

Re: Ubuntu 10.10 Netbook Edition IEEE802.11 b/g

tista さん による投稿:

#13 2010-11-08 02:23:14

Re: Ubuntu 10.10 Netbook Edition IEEE802.11 b/g

#14 2010-11-08 02:52:59

Re: Ubuntu 10.10 Netbook Edition IEEE802.11 b/g

#15 2010-11-11 11:04:46

Re: Ubuntu 10.10 Netbook Edition IEEE802.11 b/g

#16 2010-11-11 13:20:47

Re: Ubuntu 10.10 Netbook Edition IEEE802.11 b/g

コード:

コード:

コード:

コード:

Board footer

tista さんによる投稿: